Re: need info on how to remove front seat frame from 38 Packard 4 door club sedan
|
||||
---|---|---|---|---|
Just can't stay away
|
There is not any spring attached to the floorboard or seat frame. I finally got the seat to m9ve forwa4d and found two bolts holding frame t9 floofm. Got everyth8ng out and seat moved back.
Posted on: 2017/6/9 9:44
|
|||
|
Clutch adjustment 38 V127
|
||||
---|---|---|---|---|
Just can't stay away
|
The clutch on my V12 does not engage until it is less than 1/2
inch from the top of its travel. It does not slip or chatter this usually means you need to loosen the clutch adjustment rod so you have more free play. When you do this the clutch does not engave properly and the gears grind when you shift gears. Is this an indication of the clutch disc being worn out? I do not hear the throwout bearing making any noise at either adjustment point. I think the pressure plate is ok. Any ideas what is going on?
Posted on: 2017/5/26 12:16
|
|||
|
Re: need info on how to remove front seat frame from 38 Packard 4 door club sedan
|
||||
---|---|---|---|---|
Just can't stay away
|
I found 4 bolts holding the frame to seat rails. They are 5/16 by about 1 inch long. I removed them but there is still something holding the frame from coming out. I looked under floor boards and found two bolts on each side of frame Tried removing these but evidently you have to put a backup wrench
on the head of the bolt. Cannot see head of bolt because that rail is obstructing my view. Any idea how to get to the heads of these bolts? I think these four bolts are the ones that must come out but not sure.
Posted on: 2017/5/26 11:36
|
|||
|
need info on how to remove front seat frame from 38 Packard 4 door club sedan
|
||||
---|---|---|---|---|
Just can't stay away
|
Am unable to get front seat frame out of my 38 4 foor club sedan. Removing bottom cushion is not a problem. The seat will not move forward or backwardm. Need to remove seat frame
to adjust so seat will move. Any help is appreciated.
Posted on: 2017/5/24 21:00
|
|||
|
how to remove the front sear from a 1938 4 door club sedan.
|
||||
---|---|---|---|---|
Just can't stay away
|
I need help on how to remove the front seat frame from my 38 4 door club sedan. I have no problem getting the lower seat cushion out. The seat adjustment is frozen and I cannot move the seat forward or backward. The frame needs to come out ti free up the adjustment. Any help is appreciated.
Posted on: 2017/5/24 20:05
|
|||
|
New 1941 convertible coupe top
|
||||
---|---|---|---|---|
Just can't stay away
|
I am looking for a source for a new 1941 haartz stayfast canvas top. I want a high quality top
Posted on: 2016/10/18 21:29
|
|||
|
How to break lose front seat adjusters on front seat of 38 four door club sedan
|
||||
---|---|---|---|---|
Just can't stay away
|
I have raised up on the seat adjusting lever and it feels like it is releasing. Have lubricated the cog wheels on each side of seat with penetrating oil. Had a friend get in car with me and almost shoved our feet through floor boa4ds and cant get the seat to move. Looks like the seat should move back about 1 inch Any ideas about how to move seat back. It will not move in either direction.
Posted on: 2016/5/15 10:26
|
|||
|
Re: electric fuel pump to assist starting?
|
||||
---|---|---|---|---|
Just can't stay away
|
I have a 41 120 and fought vapor lock car alledgedly had a nos new pump on it. I ordered rebuild kit from then and now automotive installed and still vapor lock
Put six volt ac pump sold by great pla8ns Packard on car r8ght in front of rear axle with filter before pump. Ran wirinv through toggle zwitch on dash to ign switch. Took all guts out of pump Xcept gaskets. Made block off plate and also took out pump actuating arm. Pump on engine has fuel flowing through it but is a dummy. My vapor lock problems are over. The toggle switch Is a safety feature.
Posted on: 2016/5/15 9:04
|
|||
|
Re: 1940 packard 110 master cylinder
|
||||
---|---|---|---|---|
Just can't stay away
|
Guys
The key thing to remember is make sure the bore size of the replacement is the same as the orig8nal. I have a 41 120 and the bore siz3 is 1 inch diameter there are a lot of units out there that will work.
Posted on: 2016/5/15 8:28
|
|||
|