Packard Literature and Manuals
Packard Forums
Packard Service Index
Packard Photo Archive
Packard Model Info
Packard Owner Registry
Packard Dealerships
Packard Parts List
Packard Directory
Packard Parts X-Ref
Packard Paint X-Ref
Packard Bookshelf
All Posts (Riki)
Re: RIk's 56 ultramatic |
||
|---|---|---|
|
Home away from home
 
Joined:
2012/4/10 19:35 From San Diego, CA USA
Posts:
1544
|
Buna rubber gasket holding so far.
Attach file:  20200628_203813.jpg (700.16 KB)
Posted on: Yesterday 1:12:35
|
|
|
_________________
Riki |
||
 Transfer
|
|
|
Re: Rear flange seal. |
||
|---|---|---|
|
Home away from home
Joined:
2012/4/10 19:35 From San Diego, CA USA
Posts:
1544
|
Job complete. Torqued it 150lbs. Which is where my marks lined up.
Did have to use a cheater to remove the nut. But wasn't that tight.. Ross said it comes off. And it did.
Posted on: 7/11 23:42:33
|
|
|
_________________
Riki |
||
|
Transfer
|
|
|
Re: RIk's 56 ultramatic |
||
|---|---|---|
|
Home away from home
Joined:
2012/4/10 19:35 From San Diego, CA USA
Posts:
1544
|
My rear flange tool.
Attach file: 20200710_181207.jpg (458.28 KB) 20200710_181202.jpg (507.95 KB) 20200710_181127.jpg (503.56 KB)
Posted on: 7/10 19:38:16
|
|
|
_________________
Riki |
||
|
Transfer
|
|
|
Re: Rear flange seal. |
||
|---|---|---|
|
Home away from home
Joined:
2012/4/10 19:35 From San Diego, CA USA
Posts:
1544
|
My tool
Attach file: 20200710_181207.jpg (458.28 KB) 20200710_181202.jpg (507.95 KB) 20200710_181127.jpg (503.56 KB)
Posted on: 7/10 19:35:02
|
|
|
_________________
Riki |
||
|
Transfer
|
|
|
Re: Rear flange seal. |
||
|---|---|---|
|
Home away from home
Joined:
2012/4/10 19:35 From San Diego, CA USA
Posts:
1544
|
Ok. I'll give it a try. The book and the seal tool looks like the tool fits in the groove of seal.
But the one on my flange is like the trans seal. Thanks Ross. Ps. Just got done milling 1/2 flat cold roll (the ground will hold it) It will bolt to flange. 3 feet long. Then I hope I can loosen nut.
Posted on: 7/9 22:49:14
|
|
|
_________________
Riki |
||
|
Transfer
|
|
|
Rear flange seal. |
||
|---|---|---|
|
Home away from home
Joined:
2012/4/10 19:35 From San Diego, CA USA
Posts:
1544
|
Is this the right seal.?
Mine looks like regular seal. Attach file: 20200709_151930.jpg (646.40 KB) 20200709_152039.jpg (480.15 KB) 20200709_151939.jpg (650.83 KB)
Posted on: 7/9 15:28:34
|
|
|
_________________
Riki |
||
|
Transfer
|
|
|
Re: RIk's 56 ultramatic |
||
|---|---|---|
|
Home away from home
Joined:
2012/4/10 19:35 From San Diego, CA USA
Posts:
1544
|
Hefty bushing. Trans back in car. Was a battle .
Torque converter slipped right in. Have to button up things. And broke wires off limit switch. So. Have to remove it and try to solder wire. Attach file: 20200624_201724_HDR.jpg (606.83 KB)
Posted on: 7/2 0:19:14
|
|
|
_________________
Riki |
||
|
Transfer
|
|
|
Re: Identification of part |
||
|---|---|---|
|
Home away from home
Joined:
2012/4/10 19:35 From San Diego, CA USA
Posts:
1544
|
I have not seen that on a 56.
Posted on: 6/27 16:12:43
|
|
|
_________________
Riki |
||
|
Transfer
|
|
|
Re: RIk's 56 ultramatic |
||
|---|---|---|
|
Home away from home
Joined:
2012/4/10 19:35 From San Diego, CA USA
Posts:
1544
|
Rebuilt check up. Uk dd doesn't have taper on dd.
Plate looks barely worn. Maybe a thou or 2 miles on it. Attach file: 20200622_203952_HDR.jpg (805.81 KB) 20200622_210356_HDR.jpg (749.07 KB)
Posted on: 6/22 23:06:48
|
|
|
_________________
Riki |
||
|
Transfer
|
|
|
Re: Ford fuel pump |
||
|---|---|---|
|
Home away from home
Joined:
2012/4/10 19:35 From San Diego, CA USA
Posts:
1544
|
Arms. Don't match.
So next move. The ford uses 2 heavy springs. Might change arm spring with Carter it's lighter. And remove that spring on arm. But still gave worn spot on ford arm. Attach file: 20200621_175159(1).jpg (564.92 KB) 20200621_174452.jpg (447.04 KB)
Posted on: 6/21 18:04:30
|
|
|
_________________
Riki |
||
|
Transfer
|
|
|
