Packard Forum Index » Project Blogs

Topic: RIk's 56 ultramatic

Bottom

Previous Topic

Next Topic Register To Post

« 1 (2) 3 4 5 ... 71 »

R H

Re: RIk's 56 ultramatic

#11

Home away from home

planetary alum bronze bushing ready for sizing

Attach file:

(59.56 KB)

(68.46 KB)

Posted on: 2013/9/30 22:41

Riki

R H

Re: RIk's 56 ultramatic

#12

Home away from home

rear pump ready for sizing

Attach file:

(147.88 KB)

Posted on: 2013/10/3 23:49

Riki

R H

Re: RIk's 56 ultramatic

#13

Home away from home

today remote filler, also made stainless cap

tomorrow hook it up,,

then bleed brakes,

Attach file:

(75.05 KB)

(96.71 KB)

(80.02 KB)

(85.67 KB)

Posted on: 2013/10/6 0:16

Riki

R H

Re: RIk's 56 ultramatic

#14

Home away from home

remote filler done,,took awhile to get air out, now on to bleeding brakes,

Thanks Ross,

so far no leaks

Attach file:

(71.83 KB)

Posted on: 2013/10/6 12:32

Riki

R H

Re: RIk's 56 ultramatic

#15

Home away from home

high range clutch bushing, rear pump bushing planetary bushing sized and ready to go.

used a # 4 thread to give oil grooves,,put the other bushings to show the change.

one more bushing to make reactor shaft bushing.

Attach file:

(89.94 KB)

(88.81 KB)

(77.71 KB)

Posted on: 2013/10/19 20:32

Riki

R H

Re: RIk's 56 ultramatic

#16

Home away from home

bronze cam bearings alum bronze

# 5 cam bearing going in first, tool my dad made, ft part has bearing in it

adapter goes into bushing, another on the opposite side to center the rod and bushing.

turn the nut and it goes on in, takes a little time, but better than beating them in, like shops do.

next up . putting cam in, then crank, then pistons.

Attach file:

(60.77 KB)

(84.29 KB)

(79.78 KB)

(47.37 KB)

Posted on: 2013/12/15 1:17

Riki

R H

Re: RIk's 56 ultramatic

#17

Home away from home

je piston,, 4-3/16ths, and fel pro bs 40613 main seal

.093 piston ring

Attach file:

(45.89 KB)

(54.50 KB)

(37.58 KB)

(35.05 KB)

(38.07 KB)

(47.91 KB)
4498_52ddaf4955936.jpg 480X640 px

Posted on: 2014/1/20 18:05

Riki

R H

Re: RIk's 56 ultramatic

#18

Home away from home

pistons in, # 6, last one

Attach file:

(53.86 KB)

(45.34 KB)

(45.73 KB)

(40.33 KB)

Posted on: 2014/1/27 1:11

Riki

Peter Packard

Re: RIk's 56 ultramatic

#19

Home away from home

The seal at the front of the converter is for exhaust pressure from the converter only. The needle roller cage looks great but you are still going to need a lipped seal there. Good luck Peter Toet

Posted on: 2014/1/27 7:17

I like people, Packards and old motorbikes