Happy Easter and welcome to Packard Motor Car Information! If you're new here, please register for a free account.  
Login
Username:

Password:

Remember me



Lost Password?

Register now!
FAQ's
Main Menu
Recent Forum Topics
Who is Online
121 user(s) are online (74 user(s) are browsing Forums)

Members: 0
Guests: 121

more...
Helping out...
PackardInfo is a free resource for Packard Owners that is completely supported by user donations. If you can help out, that would be great!

Donate via PayPal
Video Content
Visit PackardInfo.com YouTube Playlist

Donate via PayPal



« 1 (2) 3 4 5 ... 22 »

Re: Joe's '49 Club Sedan
#11
Home away from home
Home away from home

Joe Wareham
See User information
Finished the dash wiring using a 9-circuit fuse panel modified to work with the 6 volt car. All the circuits are now individually fused rather than spliced to a circuit breaker. Since all the wire was replaced anyway, I think this is a better arrangement. Under hood wiring will be completed once the fenders are back on.

Attach file:



jpg  (120.58 KB)
8531_59529f884cd8a.jpg 800X1422 px

jpg  (81.62 KB)
8531_59529faccd7c2.jpg 1024X576 px

jpg  (77.50 KB)
8531_59529fd030c3b.jpg 1024X576 px

Posted on: 2017/6/27 13:12
 Top  Print 
 


Re: Joe's '49 Club Sedan
#12
Home away from home
Home away from home

Joe Wareham
See User information
I'm getting ready to start assembling the front sheetmetal on my Packard. There are an awful lot of parts involved, not including the fenders themselves. I'm going to try putting it together a piece at a time with the fenders last rather than all at once like at the factory. Probably test fit it to make sure I know where everything goes.

Attach file:



jpg  (65.32 KB)
8531_596b868a0dc8a.jpg 1024X768 px

Posted on: 2017/7/16 10:30
 Top  Print 
 


Re: Joe's '49 Club Sedan
#13
Just can't stay away
Just can't stay away

zougeride
See User information
Dear Tinman:

Re: Joe's '49 Club Sedan. Could you explain the modifications to the fuse panel so that I may copy your effort?

Again, I have enjoyed all of your postings on another forum.

Zougeride

Posted on: 2017/7/16 15:15
 Top  Print 
 


Re: Joe's '49 Club Sedan
#14
Home away from home
Home away from home

Joe Wareham
See User information
I removed the flasher. It was setup for both turn signals and hazard. The base was 5 or 6 pin with an LED-capable flasher. The original turn signal flasher was wired using power from one of the fused circuits. There was a horn relay wired directly to the panel. It was 12 volt and used a 3-pin relay. Removed the relay and the wire from the panel and will use the original horn relay connected to a fused circuit. The panel came with a 30A fuse in the panel. I replaced the fuse with a 30A circuit breaker wired to the original headlight switch which also has a 30A CB. It wasn't too difficult to merge the 12V fuse panel to the original wiring diagram, being careful that the wire gauges were sufficient for a 6V system. Since only the firewall back has been finished, I haven't cleaned up my wiring notes yet. Here's the link to the wiring diagram for the kit I used.

http://www.americanautowire.com/PDFLink/92971504%20510625%20IN%202.0.pdf

Someone asked me about the switch in the fog light position in the picture, it's the starter button.

Posted on: 2017/7/17 13:03
 Top  Print 
 


Re: Joe's '49 Club Sedan
#15
Home away from home
Home away from home

Joe Wareham
See User information
My '49 Packard project has been slowed down somewhat by the extreme heat here in Florida and a torn meniscus in my knee. I've been going through the thousands of pictures I've taken since this adventure began in 2013 and put together a summary of the progress of the project over the last 4 years.

Packard Project Summary 2013

I purchased the car in May 2013 after seeing it sitting in a gas station in St. Petersburg, FL. The previous owner took it to the gas station to have the brakes worked on. The costs were getting out of control and he threw in the towel and put the car up for sale. The engine ran but the car was rusted badly. I was actually looking for an early 50s Mercury but when I saw this car I loved the design and thought it make a nice driver that would be different from the vast number of Fords and Chevys around. I knew it could never be a show car because every piece of chrome on the car with the exception of the bumpers was shot.

Fortunately, sometime in the past, the front fenders and hood were replaced from a rust-free Series 22. The doors, rockers, quarters and trunk were badly rusted and that was the first task to repair. The trunk and rockers were replaced with new sheetmetal purchased on ebay. Patches were fabricated for the bottom of the doors and both quarter panels. The broken passenger window glass was replaced with a piece made by a local glass shop. The car was starting to look much better and my watching ebay for replacement parts was starting to pay off. I was able to replace all of the interior chrome and the entire front grille and associated trim from ebay at a reasonable price. At this point, I figured the car might have a brighter future than originally envisioned. I like to do upholstery, so for a change of pace, I rebuilt the front and rear door panels and started on a sewing a new headliner. So ended 2013.

Attach file:



jpg  (414.22 KB)
8531_5978d96f1c99c.jpg 1920X1440 px

jpg  (295.77 KB)
8531_5978d986a9545.jpg 1920X1440 px

jpg  (243.85 KB)
8531_5978d9a203b73.jpg 1920X1440 px

jpg  (284.56 KB)
8531_5978d9b50dded.jpg 1920X1440 px

jpg  (294.96 KB)
8531_5978d9c678588.jpg 1920X1440 px

jpg  (217.55 KB)
8531_5978d9daa9f61.jpg 1920X1440 px

jpg  (245.29 KB)
8531_5978d9fa97c67.jpg 1920X1440 px

jpg  (290.79 KB)
8531_5978da1399712.jpg 1920X1440 px

jpg  (65.64 KB)
8531_5978da2d75225.jpg 1024X768 px

jpg  (278.72 KB)
8531_5978da57bd89d.jpg 1920X1440 px

jpg  (227.99 KB)
8531_5978da714d7a2.jpg 1920X1440 px

jpg  (170.64 KB)
8531_5978da85482cb.jpg 1920X1440 px

jpg  (165.51 KB)
8531_5978da96e0afe.jpg 1920X1440 px

jpg  (163.75 KB)
8531_5978daa9d600e.jpg 1920X1440 px

Posted on: 2017/7/26 13:09
 Top  Print 
 


Re: Joe's '49 Club Sedan
#16
Home away from home
Home away from home

Joe Wareham
See User information
Packard Project Summary 2014

Coming to my senses after New Year's, I put the upholstery aside and got back to the less desirable job of bodywork. The car was stripped of the grille trim and bumpers. The areas around the taillights were badly rusted and poorly repaired. Someone had slapped fiberglass cloth right a large rust hole! Peeled it out, cut out the bad section and welded in a patch, filled, sanded and primed. Rusted areas of the floor by the rockers cut out and patched. At this point, the worst rusted parts of the body were repaired and it was time to work on the rest of the pieces. The hood, front fenders and the body were prepped and primed.

The body was unbolted, removed from the chassis, placed on a body dolly and put aside while the drivetrain and chassis were addressed. The engine and transmission were removed from the chassis and the chassis was stripped bare. It was cleaned, primed and painted. Likewise, all the chassis components, the front and rear suspension, pedals and linkages were also cleaned and painted. As the year came to a close, the reassembly of the chassis began and new fuel and brake lines were mocked up.

Attach file:



jpg  (73.10 KB)
8531_597a1b8b10411.jpg 1024X768 px

jpg  (59.53 KB)
8531_597a1b972c488.jpg 1024X768 px

jpg  (70.12 KB)
8531_597a1ba461ea3.jpg 1024X768 px

jpg  (55.48 KB)
8531_597a1bb349fb9.jpg 1024X768 px

jpg  (88.17 KB)
8531_597a1bc124c9a.jpg 1024X768 px

jpg  (73.24 KB)
8531_597a1bce79f7a.jpg 1024X768 px

jpg  (50.79 KB)
8531_597a1be1156ca.jpg 1024X768 px

jpg  (59.86 KB)
8531_597a1bf1af526.jpg 1024X768 px

jpg  (51.83 KB)
8531_597a1c084983f.jpg 1024X768 px

jpg  (83.80 KB)
8531_597a1c221749e.jpg 1024X768 px

jpg  (57.35 KB)
8531_597a1c380afa1.jpg 1024X768 px

jpg  (63.67 KB)
8531_597a1c4c66807.jpg 1024X768 px

jpg  (90.62 KB)
8531_597a1c5ecaf3f.jpg 1024X768 px

jpg  (103.91 KB)
8531_597a1c7439065.jpg 1024X768 px

jpg  (102.90 KB)
8531_597a1c9cbdb7f.jpg 1024X768 px

jpg  (88.51 KB)
8531_597a1cb06755f.jpg 1024X768 px

jpg  (96.58 KB)
8531_597a1cc06eff0.jpg 1024X768 px

jpg  (104.87 KB)
8531_597a1cd814c32.jpg 1024X768 px

jpg  (100.27 KB)
8531_597a1ce7eda44.jpg 1024X768 px

jpg  (86.83 KB)
8531_597a1cfb54ba8.jpg 1024X768 px

Posted on: 2017/7/27 12:07
 Top  Print 
 


Re: Joe's '49 Club Sedan
#17
Home away from home
Home away from home

Joe Wareham
See User information
Packard Project Summary 2015 - Part 1

With most of the work on the chassis was completed, attention turned to the engine and transmission. The engine ran well and the transmission shifted fine but the overdrive was inoperative and there was a massive rear main oil leak and the clutch was slipping and chattering.

I decided to go ahead and rebuild the engine. Once the transmission was removed, it was obvious why the clutch was malfunctioning. The oil from the engine caused the disk to slip and burn the surfaces of the flywheel and pressure plate. As well, there were broken springs in the pressure plate that contributed to the problems. A clutch shop in Tampa resurfaced the flywheel, completely rebuilt the pressure plate with all new springs and rebuilt the original disk with new friction material at a very reasonable cost.

To work on the engine, I built an engine stand out a hoist and pieces of another traditional engine stand. There were 3 different front mounts for the engine stand so it could be worked on right side up, upside down or sideways. It is absolutely the heaviest thing I've ever worked on. The engine was in very good shape. It was disassembled and thoroughly cleaned and flushed. It got a new set of standard rings and rod and main bearings and gasket set from Egge. No machine work was necessary just the cylinders honed and valves ground. After reassembly, it was masked up, primed and painted. The transmission was inspected and was free of damage or worn-out parts. It was cleaned and flushed and reassembled.

At this point, the engine and transmission were ready to go back in the chassis.

Attach file:



jpg  (49.98 KB)
8531_597b5ed38ae91.jpg 800X600 px

jpg  (56.17 KB)
8531_597b5edd7030d.jpg 640X480 px

jpg  (42.20 KB)
8531_597b5eeb8f130.jpg 640X480 px

jpg  (40.17 KB)
8531_597b5f056c8e1.jpg 640X480 px

jpg  (44.21 KB)
8531_597b5f1692ee3.jpg 640X480 px

jpg  (42.18 KB)
8531_597b5f2029061.jpg 640X480 px

jpg  (57.35 KB)
8531_597b5f2ccbd86.jpg 640X480 px

jpg  (48.41 KB)
8531_597b5f3c77522.jpg 640X480 px

jpg  (40.79 KB)
8531_597b5f4e3451b.jpg 640X480 px

jpg  (52.94 KB)
8531_597b5f59a20db.jpg 640X480 px

jpg  (48.66 KB)
8531_597b5f69f3f42.jpg 640X480 px

jpg  (51.18 KB)
8531_597b5f8d0d1d7.jpg 640X480 px

jpg  (46.53 KB)
8531_597b5fa3b1f35.jpg 640X480 px

jpg  (48.53 KB)
8531_597b5fbf84405.jpg 640X480 px

jpg  (49.29 KB)
8531_597b5fe330623.jpg 640X480 px

jpg  (45.30 KB)
8531_597b601e1ae1c.jpg 640X480 px

jpg  (48.76 KB)
8531_597b603303ebe.jpg 640X480 px

jpg  (44.76 KB)
8531_597b6046ef574.jpg 640X480 px

jpg  (53.59 KB)
8531_597b605b6b3b5.jpg 640X480 px

jpg  (41.63 KB)
8531_597b60766ef6c.jpg 640X480 px

Posted on: 2017/7/28 11:06
 Top  Print 
 


Re: Joe's '49 Club Sedan
#18
Home away from home
Home away from home

Joe Wareham
See User information
Packard Project Summary 2015 - Part 2


The engine and transmission were placed back in the chassis. The header pipe from the exhaust manifold to muffler was in good shape and was re-used and a generic Walker muffler of the right size was added. A new tailpipe was made from patterns and bent by a local muffler shop for $35.

The engine was temporarily wired to start and was run for several 20 minute periods at various speeds to break-in the new components. Distributor uses a 6V electronic module rather than points and condenser along with a new 6V coil. The engine ran very smoothly, good oil pressure, no overheating problems, temperature was monitored with a non-contract thermometer during break-in. The engine and chassis were covered up and put aside so that the final bodywork could begin.

As the year ended, the firewall and cowl were stripped and primed. Then the underside of the body was undercoated.

Attach file:



jpg  (55.51 KB)
8531_597cc1503d709.jpg 640X480 px

jpg  (45.63 KB)
8531_597cc16378519.jpg 640X480 px

jpg  (39.39 KB)
8531_597cc178c4269.jpg 640X480 px

jpg  (47.25 KB)
8531_597cc18a3af93.jpg 640X480 px

jpg  (61.07 KB)
8531_597cc1a287c04.jpg 640X480 px

jpg  (54.71 KB)
8531_597cc1b49b01b.jpg 640X480 px

jpg  (40.55 KB)
8531_597cc1c4d3a4e.jpg 640X480 px

jpg  (49.07 KB)
8531_597cc1d3a66e4.jpg 640X480 px

jpg  (41.23 KB)
8531_597cc1e64ae57.jpg 640X480 px

jpg  (56.92 KB)
8531_597cc1f534428.jpg 640X480 px

Posted on: 2017/7/29 12:13
 Top  Print 
 


Re: Joe's '49 Club Sedan
#19
Forum Ambassador
Forum Ambassador

HH56
See User information
The oil lines are a neat install. They appear to follow the late 1948 SC but am curious if anyone knows how long that implementation was in effect. Wonder if they did it that way on all solid lifter cars or if it just went to the early 49s until the optional hydraulic lifters became more the standard.

At some point they changed the early routing thru the filter and then to the lifters. By at least 51 it appears those 288/327 blocks had gone full flow to lifters all the time with the bypass to the filter. That was done by reinstating use of the small curved pigtail and using a 4 way fitting on the lower port. Filtered oil was dumped into the crankcase via a port on the lower edge of block.

The low flow after the filter was OK for solid lifters but much like the 356 engines they found issues on cars with hydraulic lifters as the filters got dirty.

Posted on: 2017/7/29 12:57
Howard
 Top  Print 
 


Re: Joe's '49 Club Sedan
#20
Home away from home
Home away from home

Joe Wareham
See User information
Howard,

The production number on the car is 5128 in the Series 23. Probably fairly early in the Series 23 run. Plus it's a 288 in a Packard 8 with solid lifters.

Posted on: 2017/7/31 13:09
 Top  Print 
 




« 1 (2) 3 4 5 ... 22 »




Search
Recent Photos
Photo of the Day
Recent Registry
Website Comments or Questions?? Click Here Copyright 2006-2024, PackardInfo.com All Rights Reserved