Happy Easter and welcome to Packard Motor Car Information! If you're new here, please register for a free account.  
Login
Username:

Password:

Remember me



Lost Password?

Register now!
FAQ's
Main Menu
Recent Forum Topics
Who is Online
108 user(s) are online (68 user(s) are browsing Forums)

Members: 0
Guests: 108

more...
Helping out...
PackardInfo is a free resource for Packard Owners that is completely supported by user donations. If you can help out, that would be great!

Donate via PayPal
Video Content
Visit PackardInfo.com YouTube Playlist

Donate via PayPal



« 1 2 (3) 4 »

Re: In-Car Rebuild
#21
Home away from home
Home away from home

Packard Don
See User information
There is much information on the Internet about this process, one if which is here.

Posted on: 2020/9/30 18:45
 Top  Print 
 


Re: In-Car Rebuild
#22
Home away from home
Home away from home

JeromeSolberg
See User information
This is a good Youtube Video, but there are lots of them out there:

https://www.youtube.com/watch?v=j3IIoSm1eJY

Here's Evapo-Rust vs. Electrolysis:

https://www.youtube.com/watch?v=8dtDLQHjHBc

And a nice web-page:

https://antique-engines.com/electrol.asp

You can use it for tools, parts, pretty much anything. In my experience (and also according to theory) it doesn't affect the machined surfaces, other than removing whatever rust exists on those.

I haven't had a chance to try my wooden dowels out yet, though my initial look said it might work, but again any tips on how to get the pistons out from the bottom for Cylinders #1 and #2 would be appreciated. I don't want to get started and not get them out.

Thanks in advance.

Posted on: 2020/9/30 23:23
 Top  Print 
 


Re: In-Car Rebuild
#23
Home away from home
Home away from home

Packard Don
See User information
I seem to recall that I had to (with a wood dowl) tap gently on the surface where the rod bolts come through, making sure not to let the top of the rod get jammed against the bottom of the block. You'll either need to remove the bearing or take steps to keep it from falling out. Without the rod bearing, you can even tap lightly on the bore of the rod. Whichever way I did it, I don't recall it being difficult and they came right out.

Posted on: 2020/10/1 1:41
 Top  Print 
 


Re: In-Car Rebuild
#24
Home away from home
Home away from home

Steve
See User information
Dang! How did I get to be 77 years old, enjoying my old cars for the last 50 years and learn something totally new...to me...about rust removal, 12V power, anodes and the rest of the process. I guess if you stop learning you die.
Thank you for keeping me alive.

Posted on: 2020/10/1 9:14
Steve
Old cars are my passion

1951 Packard 200
1953 Packard Clipper Custom Touring Sedan
1955 Dodge Custom Royal Lancer Tri-tone
1966 Rambler Classic 770 Convertible
 Top  Print 
 


Re: In-Car Rebuild
#25
Home away from home
Home away from home

JeromeSolberg
See User information
Well, after a bit more than 2 hours of struggle, I was able to get Pistons #1 and #2 removed. I put rubber tubing over the rod studs as recommended, and used some thin (1/2") oak dowels. It was not fun or easy, and there is barely enough room, but I was able to get it done without any adverse effects. After I got it past the first ring, I could with very little pressure lever it out. Pistons look o.k., they have new-style 3-piece oil control rings, the ring grooves are seemingly in good shape, not much carbon buildup evident. Cylinder bores after more inspection look better than I thought. Bottom rod bearing for Cylinder #2 doesn't look so hot, but I plan on replacing those. Pictures and measurements over the weekend. Pistons #3-#8 should be simple as pie after that, cross your fingers.

Thanks again everyone.

Posted on: 2020/10/2 0:47
 Top  Print 
 


Re: In-Car Rebuild
#26
Home away from home
Home away from home

JeromeSolberg
See User information
I was able to get all the pistons out. Here is what I have learned so far:d

To get the pistons out from cylinders #1 and #2 (which took me a bit of time last night) I used a 1/2" diameter oak wooden dowel, cut down to 21" long, which turned out to be just barely long enough. It could have been longer but I have the car up on riser ramps, so I only have limited clearance below the car.

All the pistons actually "look" good, in that I don't find any significant scoring or other damage, and they aren't loaded up with carbon deposits They look like the original pistons. They should be easy to clean up if I was able to re-use them.

The main observations are this:

The top ring groove-to-ring clearance, measuring a few pistons, is larger than spec (< 0.006" in the service manual), it is on the order of 0.008" to 0.009" using feeler gauges.

Piston #8 has a small "burr" on the bottom of the top ring groove.

Most of the rod bearings look "good", but there are a few with some obvious imperfections. Probably makes sense to fit new rod bearing.

I have been working on trying to measure the pistons skirts, they are somewhere between 3.500 and 3.498 at their widest point, I have a friend with better measuring equipment who is going to help with this tomorrow.

So it looks like I will need new pistons, which is disappointing because it appears these are the original pistons. Are the pistons from Kanter of the same intricate design? Of course one of the other issues is what is the bore of the cylinders, which I am going to work on measuring with the assistance of my friend tomorrow.

The other thing I did was clean out the combustion chambers from the head, using mostly a brass brush on my drill. I am getting ready to use electrolysis on this as well.

Thanks for your interest.

Attach file:



jpg  (208.29 KB)
148538_5f79671bae371.jpg 1920X1080 px

jpg  (188.86 KB)
148538_5f79672f4d6cb.jpg 1920X1081 px

jpg  (159.53 KB)
148538_5f7967453ff1e.jpg 1920X1080 px

jpg  (203.56 KB)
148538_5f79676474fbf.jpg 1920X1079 px

jpg  (101.50 KB)
148538_5f79678c3c32e.jpg 1920X1080 px

jpg  (117.69 KB)
148538_5f7967b7c049f.jpg 1920X1080 px

jpg  (261.07 KB)
148538_5f79680d97a5e.jpg 1741X979 px

jpg  (115.89 KB)
148538_5f796848b9f38.jpg 1920X1080 px

jpg  (176.10 KB)
148538_5f7968690dd7f.jpg 1920X1081 px

jpg  (176.10 KB)
148538_5f796878d3241.jpg 1920X1081 px

jpg  (230.65 KB)
148538_5f796893dc9b4.jpg 1920X1080 px

jpg  (221.13 KB)
148538_5f7968a7588dd.jpg 1774X998 px

jpg  (232.67 KB)
148538_5f7968b9e2aee.jpg 1765X993 px

Posted on: 2020/10/4 1:17
 Top  Print 
 


Re: In-Car Rebuild
#27
Home away from home
Home away from home

JWL
See User information
Those piston rings look to have huge gaps. I'll bet it had lots of blow by and consumed lots of oil.

Posted on: 2020/10/4 11:53
We move toward
And make happen
What occupies our mind... (W. Scherer)
 Top  Print 
 


Re: In-Car Rebuild
#28
Home away from home
Home away from home

JeromeSolberg
See User information
It did consume a lot of oil, and there was a lot of oil and carbon deposits in the combustion chamber.

Posted on: 2020/10/4 17:17
 Top  Print 
 


Re: In-Car Rebuild
#29
Forum Ambassador
Forum Ambassador

Owen_Dyneto
See User information
To your question about Kanter's pistons for your engine, last time I inquired (about a year ago) they were of the autothermic strut design and I assume they still are but it just takes a phone call to them to verify.

Posted on: 2020/10/4 19:34
 Top  Print 
 


Re: In-Car Rebuild
#30
Home away from home
Home away from home

jfrom@kanter
See User information
The pistons that we offer still use the strut designed as describe by Owen_Dyneto. If you have any questions on any of our products please feel free to shoot me a PM.

Thanks
James From
Kanter Auto Products

Posted on: 2020/10/5 7:52
 Top  Print 
 




« 1 2 (3) 4 »




Search
Recent Photos
Photo of the Day
Recent Registry
Website Comments or Questions?? Click Here Copyright 2006-2024, PackardInfo.com All Rights Reserved