1941-47 Clipper (19th->21st Series) - CLUTCH
|
| Subject | Application | Document |
Chatter, Clutch low, reverse - motor supports, stabilizer (snubber), clutch plate condition | (all models) | |
Data, Special Clutch - Correction column names incorrect - revised chart | 21st | |
Data, Special Clutch alternate source - identification, adjustments, parts reference | 21st | |
Data, Special Clutch alternate sources, not interchangeable - identification, part number reference | 21st | |
Diagnosis, Correct chatter, slip, spin | (all models) | |
Driven Plates and Friction Lag braking/damping action, noise reduction - identification, parts reference | 21st | |
Electromatic: Adjusting...the Clutch common mistakes - linkage stops, spool rod, body plug | 19th-20th | |
Electromatic: Adjustment engagement characteristics - preferred settings | 19th | |
Electromatic: Aero-Drive Indicator Light on when standing - fuse check | 19th-20th | |
Electromatic: Carburetor Control Linkage Equipment choke, start switch, clutch issues - lost motion, service parts kit (all models) | 20th | |
Electromatic: Carburetor Control Linkage Equipment choke, start switch, clutch issues - lost motion, service parts kit | 20th | |
Electromatic: Clutch new model information - improved design, adjustments | 21st | |
Electromatic: Clutch Cable Adjustment crankshaft main bearing wear, end play - operation and checks | 21st | |
Electromatic: Clutch Control Cable Adjustment excessive crankshaft end play - checks, modifications | 21st | |
Electromatic: Clutch Instructions superseded, discard - illustrations renumbered, adjustments/checks revised | 19th | |
Electromatic: Clutch Screw Driver and Wrench new special tool - first/reverse solenoid | 19th | |
Electromatic: Clutch Screw Driver and Wrench redesigned for new taper head screw | 19th | |
Electromatic: Clutch Valve Adjustment erratic performance, sticky spool rod/sleeve - clean, never lubricate | 19th-20th | |
Electromatic: Clutch Valve Adjustment lost motion - install valve linkage spring, clean spool rod | 19th-20th | |
Electromatic: Clutch Valve Poppet Valve Seat - new type identification - installation | 21st-23rd | |
Electromatic: Clutch, Packard... - Owner's Instructions instructions, theory of operation - schematic, adjustments/checks | 19th | |
Electromatic: Control Valve Kit, Additional Parts for Repairing valve spring, seat details - now available | 21st-22nd; (23rd) | |
Electromatic: Control Valve Repair Kit new kit facilitates reconditioning - other details | 21st-22nd; (23rd) | |
Electromatic: Disengagement sticking in high gear, decelerating - governor switch | 19th | |
Electromatic: Engagement sharp engagement, low idle - increasingmotor speed | 1951 | |
Electromatic: Failure to Release stalling - governor circuit switch checks and adjustments | 19th-20th | |
Electromatic: No-Rol, ...and incompatibilities - not recommended together | 19th | |
Electromatic: Red Pedal Pads back in stock - easy equipment identification | 19th-21st | |
Electromatic: Wiring constant battery drain - governor/ignition switch wires | 19th | |
Electromatic: Wiring Diagram new model information - Clipper | 2000-01-03-06-10-11 | |
Electromatic: Wiring Diagrams new model information - Clipper | 1951 | |
Finger Adjustment Dimensions, Clutch reference - special tool | 120B-138CD; 115C; 15th-20th | |
Flat Rate Manual 1941-49, Changes and Corrections in clutch pedal booster spring | 19th-23rd | |
Pedal Adjustment, Clutch slippage, sticking in gear - free play | (all models) | |
Pedal Shaft Lubrication, Clutch and Brake frame damage - inaccessible grease fitting, proper position | 21st | |
Pedal to Relay Lever Link, Clutch superseded part - 23rd Series type, installation | 1951; 2000-01-03-06-10-11; 21st-22nd | |
Pedal: Failure of Clutch...to Return over-stretched booster spring - proper installation | 2100-01-11 | |
Pressure Spring, Clutch parts reference - identification | 7th-20th | |
Splasher, Frame mud/ice, linkage interference - new part, location | 2000-01-03-06-10-11 | |
Splasher, Frame mud/ice, linkage interference - reiterated | 2000-01-03-06-10-11 | |
Throwout Lever, Clutch - Taxicabs failure, new design coming - reinforcing present lever | 2130 | |
Throwout Lever, Clutch - Taxicabs Supplement new heavier design available - modifications | 2130 |
SC = Service Counselor | SL = Service Letter | STB = Service Technical Bulletin | SSB = Studebaker Service Bulletin |
NOTE: These PDFs were created from High Quality Scans. It is recommended that you Right Click on the link(s) above and do a "Save Target As". This will download the PDF to your machine rather than trying to open and view it over the web.
Disclosures & Disclaimers
Though previously published elsewhere, this work is provided with my full permission for display on the PackardInfo.com website and the personal use of visitors to that site. Any other unauthorized use, however, is expressly prohibited and may be subject to prosecution.
Also, because this index was compiled from documents published by the factory, neither the author nor PackardInfo.com are responsible for errors in content arising from source information.
