Packard Motor Car Information

Re: Henry's 55 Constellation

Posted by Cli55er On 2010/9/12 20:45:57

Quote:

Ross wrote:
Switching back to torque convertor world: presumably, the end play was at least functional before disassembly, and you have not changed any of the components that control end play, soooooo it should snap back together. I know, I know.

Anyway be sure the thrust washers shown if figures 59, 60, and 63 of the shop manual are not sitting cocked, or perhaps have their locating tangs on top of instead of next to a bolt head. It is a little tricky to get the reactor rear washer settled in the right place. Check it out and make sure its tangs have not somehow gotten bent. Without your o-ring, the two halves of the convertor should kiss without resort to force.

Ross you are 100% right, the tangs on that one washer were lined up wit the bolts and not between the bolts when i put it together......then i tightened it all down on top of that and crushed the crap out of that piece. i was able to pound it back out flat, but i wont use it...i'll seek a NOS or a good used. i have asked Mike Dotson if he had any. if anyone else has that part and it is in good shape i sure could use it. you can see it in the pictures. i think it is group 3.6173...the one with the prongs.

i took out the old one from my old TC....but it was crap on the bottom, so i couldn't use it. you can see the that someone decided to cut off the top of that reactor shaft on my old one....rendering it worthless...man they really did jack up that old TC.

well i flattened out the one i bent and got it lined up right and BAM it went together without any problems and i was able to turn the reactor shaft both was without any issues. the bearing that i brushed is still not right because before i brushed it i couldn't move the reactor shaft just by putting it in the converter pump housing itself and trying to turn it from top or bottom. so i think a new bushing is needed, i asked Mike Dotson about that one too.

Mike Franko let me borrow his Kent Moore end play tool.....and it was perfect....fyi all you need is one that is 1" diameter and it is perfect. THANKS MIKE FRANKO!!! you da man!! i tightened up the Converter with the four bolts and i hooked up my dial and i was getting inbetween .007 to .009....that could have been from the bent washer that i banged back flat....or it could just not be enough and i need to adjust the thrust washer with a thinner one.

with the converter tightened i was able to turn the reactor shaft by hand in both directions and i was able to put it in the transmission without issue and it turned very easy in both directions without moving the tailshaft. so i am on the right track, just got to get few parts that got messed up from living and learning and i will be good to go.

i also worked on getting the waterpump apart.....i got it with a bit of effort. the rebuild kits from Max have the pulley mount off already, so i am guessing in will have to press of that piece and put it on the new shaft.....but looked into the hole on the pump....it looks really worn out....what do you guys think about water pump housing itself....looks worn bad.

my son threw on some gloves and dug into it with me today too. it was fun ;0)

i also got a GREAT gift from Mike Franko too....some pieces that belonged to my Grandfather. things that were about the 1937 Limo 138cd. even the title all the way back to 1973 and the owners name before 1973. a complete ledger of all things bought and done to the car. the original ad posted by my Grandmother when my Grandfather died.

my Grandfather was was an architect and he loved to drawl his renditions of Packard cars.

I also have letter from PMCC date 1948 from the advertising dept.

the vibratory machine told me never to add any kind of fluid to the material, maybe the eastwood one is different design. idk.

Hank

Attach file: