Re: Ken's 1953 Packard Clipper Deluxe Touring Sedan

Posted by kens53clip On 2009/11/25 12:38:53

On Labor Day, 2009, I removed the front and rear seats cushions from the Packard to try to determine if they were original to the car. Several of them had 2662 stamped on them (which is the model of the car, Clipper Deluxe touring sedan). One had 2 codes on it, one starting 2662 and one starting 2692 which is the plain Clipper touring sedan. Did somebody make a mistake in marking it 2692 (the upholstery matches the other seats)? I am under the impression that the same type of fabric was not supposed to be used in both models. The Clipper Deluxe used striped Bedford cloth. The Clipper used striped broadcloth. The bottom front seat cushion has original fabric and piping which looks very similar if not identical to the rest but really does not fit into the seat frame well, being a bit too wide from front to back. Perhaps the bottom front seat cushion may come from a different year or model Packard?

When the back seat had been removed I discovered that the rear package shelf cover could be lifted off. After lifting off the rear package shelf, I was able to discover for the first time what was in the car's trunk (not having a key to the trunk). In leaning against the fiberboard separating the passenger compartment and the trunk, I unintentionally popped a couple of the fasteners, discovering that the fiberboard was not fastened very firmly. I then popped the remainder of the fasteners, which were not very firmly attached, and removed the fiberboard, allowing better access to the trunk.

What do you think was in the trunk??
(a) Gold Doubloons and Pieces of Eight?
(b) Jimmy Hoffa?
(c) a Crosley convertible emergency vehicle?
(d) car parts?

If you guessed (d) you were correct. Most parts appeared to be used but some might still be usable. Here's what was in the trunk:

1. Two Trico Rainbow wiper blade RB 11 boxes, containing metal part of Trico wiper blades and a small portion of the original rubber blades.

2. One Trico Rainbow wiper blade RB 12 box containing Trico wiper blade metal parts.

3. One AC PCV valve CV609C (with box). I may not be a mechanical genius but I know my Packard did not have this (given the road tube and the breather oil cap). Anybody know what this goes to?

4. One GE sealed beam headlight M150

5. One box for a Niehoff AL-130 6 volt solenoid

6. One used (six volt?) solenoid marked 1465

7. One used Champion Sparkplug J-11

8. One Delco-Remy condenser box marked D-203 192811 and three used condensers, one marked 2D020, one marked Echlin, and the other unmarked

9. Two used distributor rotors, one an Echlin RR-159, the other unmarked

10. Two pushbutton door light switches (interior light comes on when door opens and button is no longer pushed in)

11. Two point sets, one marked Delco-Remy, the other marked Echlin

12. Key ignition switch labeled "starter" in chrome (I know it is not from this car)

13. Echlin RR-158 distributor cap box and an unmarked distributor cap

14. GE 1155 bulb

15. Used brake spring

16. Used fuel line hose

17. Used heater hose and clamps

15. 1154 bulb

16. Used 6 volt battery from Nationwise Auto Parts

17. Wheel and tire with 1950's looking medium width whitewall tire

19. One 1950's looking wheel trim ring

20. Jack that looks original to car

21. Battery hold-down frame that looks original to car

22. A green plastic door lock push down knob matching others in the car

23. A ratty flannel blanket

24. A soup tureen

25. Part of an Atlanta, Georgia newspaper from 1996

The PCV valve, the key ignition switch, and any 12 inch windshield wiper parts are not proper for my car. I believe most other car parts were installed or are installable on my car but I do not know for sure. Since a lot of these parts are ignition parts, I should state that my car uses a Delco-Remy Distributor No. 1110841 which was used late in 1953 according to the Automotive Electric Association, and, according to the 1951-1954 Packard service manual, on at least some 1954 models.

I had hoped to be able to crawl in the trunk to change the burned out taillights but the steel X cross member across the trunk was fairly sharp metal and did not offer much space in which I could easily crawl so I decided to wait on the locksmith. I was able to get some of the parts out with the help of a broom. I had to use a rake to get the used battery out.