LED Bulb Wrap-up, 22nd/23rd Series
Posted by Joe On 2024/6/12 21:46:38
Hey gang. I finally decided to get into changing the rest of my bulbs in my 2302. I've shared videos of my park and tail lights on YouTube - those are an excellent upgrade and highly recommended.
Inside, the courtesy lights are wonderful. I decided to keep my incandescent for my dome light because the 82 LED bulbs only illuminate in one direction. Because the socket is on the side, it very obviously only lights half the dome light. It looked goofy, though it is very bright.
I also got my trunk light going again. For this, I purchased the reproduction tilt switch light you can get from any Ford parts supplier (C2RZ-15A700-A) - $26 from Dennis Carpenter. It's the exact same dimensions as our Hobbs mercury switch lights (even the screw holes are in the same place), but the housing is taller and the socket is larger than OE for us. For this, I put in a 6v 1129 LED bulb, which illuminates all around the bulb. Perfect fit, illuminates beautifully, and the tilt switch works exactly as it should. Cheap and easy.
One very important thing, though - LED bulbs are NOT compatible with the black light filters and Flite-Glo lighting for the dash. I hooked four in with the intent of taking a comparison photo... not even worth it. 0% luminescent. The bulbs were shining - they're bright, but not a lick of light made it through the filter. So, incandescent bulbs only for the eight bulbs that light the Flite-Glo dash. There's a 6v 3w speedometer bulb advertised for Honda motorcycles on Amazon - that's what I'm using in the photo attached here (my speedometer needle is there... the rebuilder put tape on the needle, so it doesn't glow at the moment... will fix).
Hope this helps!
Attach file:
20240612_212730.jpg (3,424.24 KB)
20240612_212428.jpg (3,680.93 KB)
20240424_013247.jpg (2,720.33 KB)
Inside, the courtesy lights are wonderful. I decided to keep my incandescent for my dome light because the 82 LED bulbs only illuminate in one direction. Because the socket is on the side, it very obviously only lights half the dome light. It looked goofy, though it is very bright.
I also got my trunk light going again. For this, I purchased the reproduction tilt switch light you can get from any Ford parts supplier (C2RZ-15A700-A) - $26 from Dennis Carpenter. It's the exact same dimensions as our Hobbs mercury switch lights (even the screw holes are in the same place), but the housing is taller and the socket is larger than OE for us. For this, I put in a 6v 1129 LED bulb, which illuminates all around the bulb. Perfect fit, illuminates beautifully, and the tilt switch works exactly as it should. Cheap and easy.
One very important thing, though - LED bulbs are NOT compatible with the black light filters and Flite-Glo lighting for the dash. I hooked four in with the intent of taking a comparison photo... not even worth it. 0% luminescent. The bulbs were shining - they're bright, but not a lick of light made it through the filter. So, incandescent bulbs only for the eight bulbs that light the Flite-Glo dash. There's a 6v 3w speedometer bulb advertised for Honda motorcycles on Amazon - that's what I'm using in the photo attached here (my speedometer needle is there... the rebuilder put tape on the needle, so it doesn't glow at the moment... will fix).
Hope this helps!
Attach file:
20240612_212730.jpg (3,424.24 KB)
20240612_212428.jpg (3,680.93 KB)
20240424_013247.jpg (2,720.33 KB)
This Post was from: https://packardinfo.com/xoops/html/modules/newbb/viewtopic.php?post_id=272773