|
Re: monroe p/s control valve stud
|
||||
|---|---|---|---|---|
|
Home away from home
 
|
Do you have pictures
Posted on: 4/2 23:12
|
|||
|
Riki
|
||||
|
||||
|
Re: Intake Manifold Needed
|
||||
|---|---|---|---|---|
|
Home away from home
|
Gerry psw
Or Tucson. Packard
Posted on: 4/1 21:03
|
|||
|
Riki
|
||||
|
||||
|
Re: RIk's 56 ultramatic
|
||||
|---|---|---|---|---|
|
Home away from home
|
Rear axle..
Round ones go on top. Rectangle ones are 55 type. Which are used for 56. More surface area. Attach file:  20240320_173729.jpg (4,287.41 KB)
Posted on: 3/30 11:29
|
|||
|
Riki
|
||||
|
||||
|
Re: RIk's 56 ultramatic
|
||||
|---|---|---|---|---|
|
Home away from home
|
Enduro soft.
Might be more what Packard used. Have to wait and these to Ross . See what ones better. Shore 80 or soft. Attach file: 20240329_190322.jpg (4,005.46 KB) 20240329_190346.jpg (4,421.91 KB) 20240329_190359.jpg (1,337.06 KB)
Posted on: 3/29 21:08
|
|||
|
Riki
|
||||
|
||||
|
Re: Bob Aller Oil Pump Rebuild
|
||||
|---|---|---|---|---|
|
Home away from home
|
For a bushing.
I used a cast iron valve guide and cut it A machine shop had a boat load of different ones. When he closes it will suck.
Posted on: 3/28 0:27
|
|||
|
Riki
|
||||
|
||||
|
Re: V8 Engine Disassembly, Inspection
|
||||
|---|---|---|---|---|
|
Home away from home
|
Buy a longer- 3/4.-14? Bolt. I think I use one 3 inches long.
For crank bolt. That gives you plenty of pull to get it off. Also. I have had no problems pulling on back of ring that's vulcanized on the cast pulley.
Posted on: 3/26 19:47
|
|||
|
Riki
|
||||
|
||||
|
Re: Bob Aller Oil Pump Rebuild
|
||||
|---|---|---|---|---|
|
Home away from home
|
I don't remember that post.
Thanks My dad's 56 was having a lifter problem. But has been quiet . But if it starts again my plan is ross.s to keep original
Posted on: 3/26 16:40
|
|||
|
Riki
|
||||
|
||||
|
Re: Bob Aller Oil Pump Rebuild
|
||||
|---|---|---|---|---|
|
Home away from home
|
Do what Ross does.
Pictures on my blog.
Posted on: 3/26 12:44
|
|||
|
Riki
|
||||
|
||||
|
Re: RIk's 56 ultramatic
|
||||
|---|---|---|---|---|
|
Home away from home
|
Going art decco.
And box of bushings going to Ross. Making 2 more 56's. Think I'll have enough. With this container of polyurethane. Thrn going to try their soft polyurethane. See if it's More like rubber. Using black tint. Does not get air bubbles. Attach file: 20240324_170140.jpg (4,155.83 KB) 20240324_170448.jpg (3,871.55 KB)
Posted on: 3/24 20:22
|
|||
|
Riki
|
||||
|
||||
|
Re: hph's 55 Clipper Project
|
||||
|---|---|---|---|---|
|
Home away from home
|
I use this.
Get about 3 feet small rubber hose and put down spark plug hole. Turn engine till it stops. This holds valve up. Attach file: 20240324_180015.jpg (4,124.61 KB)
Posted on: 3/24 20:04
|
|||
|
Riki
|
||||
|
||||
