For the extra sender, I seem to recall a plug just below the regular sender and at an angle pointing toward the passenger side. It may be slightly hidden under the breather vent tube coming off the lifter galley cover. I believe it is larger than the sender port -- maybe a 1/4 plug -- but think it also opens to the same passage the sender uses.

Another option is since the heads are interchangeable right to left there will be an unused port on the rear of both heads. Look to see where the oil filter supply tube is at the front of the left head to see where it will be positioned at the rear. Not sure you will be able to use those because of the closeness to the firewall if the sender is very large.

As to the hoses, I believe the vendors have them but you might also be able to have them made locally at a hydraulic shop. If replacement fittings are much larger or different in shape than the originals there could be issues with the two short hoses on a Bendix system. There is also a restriction in the main pressure hose that factory articles said is supposed to cut down on noise. I know hoses made locally don't have that restriction and seem to work OK so don't know how important it really is.

I don't know if the Ultramatic indicator piece carried on with the Flite-Glo instrument lighting theme since the owners manual says it is illuminated any time the ign switch is on. If so and it still glows, the paint in the letters may be cracked and barely hanging on. Just like the instruments, when you disassemble to polish the indicator try to protect the paint on the pointer and take care with the paint in the letters on back of the plastic. If the paint is damaged or chunks fall off the pointer or letters they will become splotchy or not glow at all.

If your Chrysler generator is the late 40s early 50s style with the end cap and keyed armature shaft that can mount and drive a power steering pump a couple of Packard owners having cars that can only accommodate a single fan belt have used them to add power steering to their cars.

Quote:

I don't know if that is a typo but if that is how it is currently wired the button should be on S (switch) and horns on H.

That sounds good as to where you have power. Where you do not also sounds good because unless the engine is running the cutout relay in regulator would be open so nothing on A, F and G or ground.

There is a bit of discrepancy between the factory and AEA wiring diagrams on exactly where a wire connection to the starter switch is located but both agree the voltage comes from the same place.

AEA diagram is easiest to trace and it shows voltage originating at the starter solenoid BAT terminal and going to ammeter via a red wire. AEA shows black wires out of ammeter passing that voltage to the regulator, ign switch, headlight switch input terminal and the starter button. Discrepancy is where the starter button is actually tied to be powered from. AEA has it from ammeter, factory has it from the headlight switch input terminal which comes from ammeter so essentially the same place. You might see if you have power on the power input to the headlight switch.

What can be confusing is the factory originally had the starter being able to crank engine at all times although the engine would not start without the key on. When later models came out with the starter button powered thru the ign switch so it only worked with the key on some changed their earlier cars with always active starters to match later models. In that change the starter switch is fed from the ign sw GA terminal instead of ammeter or light switch. As to not having power on one side of starter switch and solenoid, that would be correct unless the button was pushed. Power on the other side would depend on whether the feed wire came from ammeter or ign sw.

Horns take a lot of current so make sure the feed wire is 12 ga and has good tight terminals. Might also double check to make sure the wires are on the correct relay terminals. B is bat, H is horn and S is the button. If the battery feed is not on the correct relay terminal nothing works.

No reset button on the regulator.

Others can better answer the pulley question but on a two brush generator, one brush will connect to wiring going to the field coils and A terminal while the other brush will connect to case metal for the ground. If you check carefully where the braided lead from the brush with no other wire connects it is most likely being grounded to the case end plate by the brush holder or where ever the braided lead terminates.

Attach file:

---

  generator.jpg (61.08 KB)

I don't know if Lares Corporation might have or would even sell individual components or only sell and rebuild complete assys but they do advertise in Hemming's. I believe they have rebuilt steering systems for a few Packard owners who post on the forum. Don't know if other mfgs used exactly the same unit as Packard but Monroe steering was also used on some Plymouth models and their vendors might be worth checking.

Don't remember where this page is from but here is a bit showing Mopar (Plymouth) part numbers. Again, do not know if it exactly the same unit as I believe the typical Packard was heavier and might have had a larger unit than Plymouth.

Attach file:

---

  Monroe.jpg (400.95 KB)

I suspect the biggest difference between numbers would be in jet size and adjustments that were specified by the various mfgs engineering depts to be optimized for the engine it was going on.

The correct WDO carb core for your model Packard should be available relatively inexpensively from those on the forum with parts cars or some of our used vendors. If you are handy and a bit mechanically inclined rebuild kits are also easily found. You could probably do something like that for far less than the cost of a professionally done rebuild.

Another option which recently came on the market is a replacement universal 2 barrel carb from Daytona Parts. Daytona has been around for years and has done rebuilds for many of us. Their new carb may or may not need some kind of adapter to bolt to the manifold but from the description and the fact it is a new carb it might be worth looking into. I expect the price would be in the same neighborhood as a rebuilt original though.

Aside from the visual differences, probably the biggest downside to going with a universal carb is you would need to add a pushbutton to start the engine as the accelerator pedal carb start switch would no longer be there.

Most generators provide the high current ground path to the frame or battery ground connection by virtue of the generator components being connected internally to the generator case. The ground path connection is then provided to the frame or battery by the mounting bracket and bolting hardware. Since the generator is on the engine block and not the frame it is somewhat separated by rubber mounts. Some models with remote battery positions did use a ground strap between the block and frame to get to the battery ground strap.

A small secondary generator ground is only a reference and is usually connected directly to the regulator by virtue of a small gauge wire from a screw on the generator case to either a terminal on the regulator or by connecting to one of the regulator mounting screws. This ground is used only to provide a direct connection to eliminate any potential voltage difference in grounds that might be cause by a poor connection in the mounting bracket or sheetmetal. This reference is needed so the regulator knows exactly what voltage the generator is producing without any added resistance due to a poor metal to metal connection. It is not designed to carry any high current such as that needed to operate the starter or headlights etc.

A heavy ground strap or wire from the generator is not used on any Packards I have seen but it certainly would not hurt if you wanted to add something like a short braided strap between the generator mounting ear to the frame.

If you kept the relay with fuses which was assumed to be powering the sealed beam conversion make sure it is getting power and that the dimmer switch is actually turning on the relays. If you are using a stock harness and the headlight switch with city, county, pass combinations for headlights then you may need to chase wires and modify connections to eliminate some of the combinations.

Since the turn signals were not offered on 37 models it is hard to guess what might be going on without seeing a diagram of what must be an aftermarket item. There were several brands but if you can find a mfg or model a diagram might be found on the web.

Horns get power from the BAT post on starter solenoid to power the relay which operate the horns. The command is a ground from the horn button. Most cars have an inline connecter at the base of the steering box to join the wire from the button to the loom so if your car has one make sure there is a good connection with wire from button to the loom and it continues on to the relay.