1948 heater wiring
|
||||
---|---|---|---|---|
Home away from home
![]() ![]() ![]() |
Is there a wiring diagram for the 2262 heater and switch ? and fog light switch - Thanks
Posted on: 2020/4/20 21:37
|
|||
|
Re: 1948 heater wiring
|
||||
---|---|---|---|---|
Home away from home
![]() ![]() ![]() |
Thank you - My car has a heater and dash heater switch -----and a dash fog light switch, but no fog lights
Posted on: 2020/4/20 22:51
|
|||
|
Re: 1948 heater wiring
|
||||
---|---|---|---|---|
Home away from home
![]() ![]() ![]() |
I think that's par for the course, rather than make separate model configs, they put "everything" on dash panel, then only hooked up what was optioned*. I recall having a few nonfunctional buttons, except radio was a delete panel.
It's just a little "different" to think backwards in positive ground terms, if hasn't been converted. Cloth wire is hardest to familiarize, if spent life in 12V (-) PVC shield world of colors. I really need to decide what to do with my "P" project. Got a ton o money in it to sit a hulk and occupy parts shelves. The other one that wasn't supposed to come first is hopefully nearing the rebuild end. i"m working on it today AGAIN. But that one even got way-layed by a new lease vehicle. Life interferes with best of plans. Kinda like that little shiny steel ball on the pinball table, sometimes it takes a whirl, makes lights and sounds, and sometimes goes straight down the drain... * - unfortunately, unlike survivor brands, if one doesn't have a build sheet/other documentation in/on theirs, there's little way to find out "as delivered". That's even getting scarcer as paper is ephemera.
Posted on: 2020/4/22 9:04
|
|||
|
1954 Pacific H4 headlight wire harness
|
||||
---|---|---|---|---|
Home away from home
![]() ![]() ![]() |
Good Morning HH56 Howard, I hope you don't mind me jumping in. I recently replaced the headlights on my 54 Pacific. I noticed the wires were dry,brittle and exposed thru the cloth. I have received a new H4 wiring harness for the lights. Aside from yanking the wiring straight out thru the front from of the headlight body, where are the 3 wires (red, black,green) attached to inside the car? I can see 2 switches on each inner fender which makes things look complicated. Is there another easy spot where the headlight wires attach to?
Posted on: 2020/4/22 10:42
|
|||
|
Re: 1954 Pacific H4 headlight wire harness
|
||||
---|---|---|---|---|
Forum Ambassador
![]() ![]() ![]() |
The horn relay is the silver box in your second photo and the item sort of hidden by wires under it is the L side junction block. There is another junction block just like it on the right side which I believe is what is in your third photo.
The hi - lo beam wires from the dimmer switch are in the main loom and attach to the L side junction block as does the parking light feed. There is another section of loom attached on the same block which I believe in your car feeds across the front of the radiator to the right side and connects to the R junction block. With the head and parking lights connected there should be 3 wires on each terminal on the left side and two on the right. The 3 wires from the headlight buckets are in a short approx 18" length of covered wire in which 2 wires - hi and lo beam - attaches to each of the junction blocks and the third wire which is ground attaches to one of the terminal block mounting screws. Parking lights have two wires wrapped together with one wire going to the terminal block and the other to an inline connector. I can't say for sure which terminal on the block is hi, lo, or park . That you will need to determine on your car but if you can see the colors well enough the park light terminal will have pink wires on the main and aux across the radiator loom connector and will stay connected as is. The hi and low to the headlight buckets you need to replace will be with the tan or light gray wires. The 3 wires from the headlight buckets may be fabric covered and wrapped with vinyl wire wrap and look like the rest of the looms or they may be a black rubber covered cable which resembles a cord you would plug in the wall.
Posted on: 2020/4/22 12:32
|
|||
Howard
|
||||
|
Re: 1948 heater wiring
|
||||
---|---|---|---|---|
Home away from home
![]() ![]() ![]() |
I had some of the same issues. I finally bit the bullet and bought a wiring harness fromhttps://www.riwire.com
it came with great instructions. I had never tried to do anything like that and in two days the car was up and running.
Posted on: 2020/4/27 13:40
|
|||
1948 Custom Eight
1950 Super Eight Convertible |
||||
|
Re: 1948 heater wiring
|
||||
---|---|---|---|---|
Home away from home
![]() ![]() ![]() |
Howard - The wire ( GA ) from the Ignition Switch to the Heater & Defroster Switch - is it on the inside or outside of firewall ? Thanks - 48 model
Posted on: 2020/12/2 1:53
|
|||
|
Re: 1948 heater wiring
|
||||
---|---|---|---|---|
Forum Ambassador
![]() ![]() ![]() |
Power for the heater should be provided by a single loose wire running between ign sw GA terminal and the BAT terminal on the heater switch. There will be an inline fuse holder somewhere in that length. The owners manual says the 30 amp heater fuse is positioned under the clock so I would expect the wire to be laying toward the bottom of the dash. You might be able to find the fuse holder and then identify the wire.
Posted on: 2020/12/2 9:52
|
|||
Howard
|
||||
|
Re: 1948 heater wiring
|
||||
---|---|---|---|---|
Home away from home
![]() ![]() ![]() |
I agree . The power wire to the heater/defroster switch is under the dash.
Posted on: 2020/12/2 9:54
|
|||
|