Re: Electricaal issue ..41 Packard no current
|
||||
---|---|---|---|---|
Home away from home
![]() ![]() ![]() |
Forgot to mention installed entire new brake kit..so all parts are new
Posted on: 2023/5/10 8:20
|
|||
|
Re: Electricaal issue ..41 Packard no current
|
||||
---|---|---|---|---|
Home away from home
![]() ![]() ![]() |
Great info..thanks….yes I only get the smoke after engine is shut off….I will take it for a good drive when brakes are squared away and report back! Thanks
Posted on: 2023/5/10 10:20
|
|||
|
Re: Electricaal issue ..41 Packard no current
|
||||
---|---|---|---|---|
Home away from home
![]() ![]() ![]() |
Bled brakes twice and both times I lose pressure when starting engine..there is no booster so I don’t have any idea why the brakes would go to floor at ignition…I must be missing something… I cannot see any leaks at all.. maybe I can run some compressed air into line and try to see a possible leak but it must be tiny…no engine knocks at all…it runs nice …I do believe it is running rich..I’ll address that when I figure out brake issue,.thanks,
Posted on: 2023/5/10 15:19
|
|||
|
Re: Electricaal issue ..41 Packard no current
|
||||
---|---|---|---|---|
Home away from home
![]() ![]() ![]() |
That's very odd behavior on the part of the brakes. Is there any chance that hot exhaust gas is reaching any part of the brake system?
With a non power brake system, I can't think of any other way the engine running or not could affect the brakes. Have you adjusted all four brakes to spec? Are all the brake return springs in place? Are the brake drum diameters all within specification?
Posted on: 2023/5/10 15:29
|
|||
|
Re: Electricaal issue ..41 Packard no current
|
||||
---|---|---|---|---|
Home away from home
![]() ![]() ![]() |
No exhaust near brake issue…I just installed the new brake in the same fashion that old ones were in… it seemed pretty straightforward…. I’ll will check tomorrow…I need a break! Thanks
Posted on: 2023/5/10 17:04
|
|||
|
Re: Electricaal issue ..41 Packard no current
|
||||
---|---|---|---|---|
Home away from home
![]() ![]() ![]() |
Where did you get the wheel cylinders?
Had a problem with cheapo Chinese reproduction when I did mine All parts are not the same, there is a reason that some part are cheaper.
Posted on: 2023/5/10 18:52
|
|||
|
Re: Electricaal issue ..41 Packard no current
|
||||
---|---|---|---|---|
Home away from home
![]() ![]() ![]() |
Got them at kanter
Posted on: 2023/5/11 10:22
|
|||
|
Re: Electricaal issue ..41 Packard no current
|
||||
---|---|---|---|---|
Home away from home
![]() ![]() ![]() |
I think I need to adjust brakes like u mentioned..have no leaks at all…I had no idea about the adjustment pin…or how to set rear brakes… I’m looking at adjusting pin now…it looks pretty rusted…I can pb blast big nut and loosen…but what tool to turn the slot to adjust….looks like huge straight tip screwdriver?
Posted on: 2023/5/11 10:25
|
|||
|
Re: Electricaal issue ..41 Packard no current
|
||||
---|---|---|---|---|
Home away from home
![]() ![]() ![]() |
Pic
Attach file: ![]() ![]() ![]() ![]()
Posted on: 2023/5/11 10:31
|
|||
|