Re: Progress report
|
||||
---|---|---|---|---|
Home away from home
![]() ![]() ![]() |
Thank you!
Posted on: 2012/1/16 22:04
|
|||
When two men ride the same horse, one has to be in the back...
|
||||
|
Re: Progress report
|
||||
---|---|---|---|---|
Forum Ambassador
![]() ![]() ![]() |
i hope it works and i'm glad i could help, since you help me so much!
PM me how it works, since i haven't had real world testing of it, although i'm sure it will be fine.]\ and fwiw, i think all my check valves were flat too.
Posted on: 2012/1/23 14:20
|
|||
1937 Packard 138-CD Deluxe Touring Limousine
Maroon/Black 1090-1021 [url=https://packardinfo.com/xoops/html/modules/registry/View.php?ID=232]1955 Packard |
||||
|
Re: Progress report
|
||||
---|---|---|---|---|
Forum Ambassador
![]() ![]() ![]() |
Bought the binding post this morning. This being Fresno, had to check around before finding one that small. Slim pickings so guess it's not used on Chevys or tractors -- If it were, every store would carry some version of it.
One thing I'm wondering about is operating temp of Ultra. Locktite says good to 300 degrees and I wonder how close that is to operating temp. Don't want to be back in there anytime soon because the screw backed out.
Posted on: 2012/1/24 13:17
|
|||
Howard
|
||||
|
Re: Progress report
|
||||
---|---|---|---|---|
Forum Ambassador
![]() ![]() ![]() |
J.B. weld it then, put it on the threads. it would be easy to get it out again by drilling it. thing would never come off then unless you drilled it down the center of the binding post.
Posted on: 2012/1/24 13:21
|
|||
1937 Packard 138-CD Deluxe Touring Limousine
Maroon/Black 1090-1021 [url=https://packardinfo.com/xoops/html/modules/registry/View.php?ID=232]1955 Packard |
||||
|
Re: Progress report
|
||||
---|---|---|---|---|
Forum Ambassador
![]() ![]() ![]() |
JB Weld is a good idea. Thinking about it, Locktite is probably OK too. I know the car won't ever get very hot just backing out of the garage and back in after the occasional trip around the block. About all it's done for the last 15 years. Why change a good thing when I'm on a roll.
Posted on: 2012/1/24 13:54
|
|||
Howard
|
||||
|
Re: Progress report
|
||||
---|---|---|---|---|
Forum Ambassador
![]() ![]() ![]() |
also, i got that binding post from home depot....i guess they didn't have it near you?
Posted on: 2012/1/24 14:14
|
|||
1937 Packard 138-CD Deluxe Touring Limousine
Maroon/Black 1090-1021 [url=https://packardinfo.com/xoops/html/modules/registry/View.php?ID=232]1955 Packard |
||||
|
Re: Progress report
|
||||
---|---|---|---|---|
Forum Ambassador
![]() ![]() ![]() |
I went to Orchard and Lowes nearby. Those were all too long and didn't want to mess with cutting one down. Found the short one at a local owned store.
Posted on: 2012/1/24 14:23
|
|||
Howard
|
||||
|
Re: Progress report
|
||||
---|---|---|---|---|
Forum Ambassador
![]() ![]() ![]() |
exciting....i sure hope it works out. YAY a real world test for something i came up with. ;0) excited!
now, just don't let me down little binding post!
Posted on: 2012/1/24 15:52
|
|||
1937 Packard 138-CD Deluxe Touring Limousine
Maroon/Black 1090-1021 [url=https://packardinfo.com/xoops/html/modules/registry/View.php?ID=232]1955 Packard |
||||
|
Re: Progress report
|
||||
---|---|---|---|---|
Forum Ambassador
![]() ![]() ![]() |
Quote:
Sorry to say Hank, but there was a change of plans. Not the binding post idea but more the lack of a decent quality item available here. Also a reluctance on my part to do what was needed to make what is available fit. That's the part that let you down. As mentioned, had a time finding the small 3/16 x 1/4 size. It also appears that particular brand must be made under less than ideal conditions as quality seems very poor. It is labeled 3/16. I do believe that is a Metric 3/16 because it wouldn't fit without drilling out the link. Instead of an item that should fit a .187 dia hole, first one was .194. Tried another and it was worse. No idea what the quality of metal is either. Guess 71 cents just doesn't buy much. Did not want to drill anything larger and would not have been that easy to do decently while in car either. Decided to just order shoulder screws and locknuts and have done with it. Those arrived today, not nearly as inexpensive as binding posts but are .186 diameter and polishd steel. Locknut is the interference kind and should not need any locktite either. That bit still bothers me a bit on yours. Looking at link positioning, it looks as if it may be submerged or just barely out of hot oil in normal driving. Maybe you might consider the JB weld.
Posted on: 2012/1/27 15:24
|
|||
Howard
|
||||
|