BigKev	Re: BigKev's 1954 Packard Clipper Deluxe Sedan	#1581
Webmaster Joined: 2006/4/17 13:30 Last Login : Today 8:40 From North Aurora, IL Group: Webmasters Registered Users Posts: 12043	For me it's when I can go over the car without finding obvious high and low spots. Then onto finer grades of paper to remove the sanding scratches from the previous grades. I did work on the car for about another 90 mins tonight, and most of the driverside, hood and trunk are done. There is going to be some spot priming needed cover some thin areas. One low spot found that may need a little glazing filler to level it. Posted on: 2013/2/18 23:31
	-BigKev 1954 Packard Clipper Deluxe Touring Sedan -> Registry | Project Blog 1937 Packard 115-C Convertible Coupe -> Registry | Project Blog

BigKev	Re: BigKev's 1954 Packard Clipper Deluxe Sedan	#1582
Webmaster Joined: 2006/4/17 13:30 Last Login : Today 8:40 From North Aurora, IL Group: Webmasters Registered Users Posts: 12043	More block sanding on the car today. Also removed the hood and the hinges so I can prime the cowl area. Hood will stay off the car through the paint process. Attach file:   (39.46 KB)   (31.00 KB)   (24.18 KB)   (23.31 KB)   (38.98 KB)   (31.75 KB) Posted on: 2013/3/10 21:18
	-BigKev 1954 Packard Clipper Deluxe Touring Sedan -> Registry | Project Blog 1937 Packard 115-C Convertible Coupe -> Registry | Project Blog

Jim	Re: BigKev's 1954 Packard Clipper Deluxe Sedan	#1583
Forum Ambassador Joined: 2007/3/9 0:20 Last Login : 2023/2/28 17:22 From Phoenix, Arizona Group: Registered Users Forum Ambassadors Posts: 755	Heck Kev, you'll have your whole car painted before I even get my trunk lid painted going at the rate you are! Keep up the good work. Cant wait to ride around in it, maybe next PI meet! Posted on: 2013/3/10 23:26

BigKev	Re: BigKev's 1954 Packard Clipper Deluxe Sedan	#1584
Webmaster Joined: 2006/4/17 13:30 Last Login : Today 8:40 From North Aurora, IL Group: Webmasters Registered Users Posts: 12043	Got the hood completely sanded leveled, just need to reshoot the edges and spot prime a couple of thin areas. Masked off the bottom.side so I can reprime all the sides and bottom surface edges. Then I will do.the final sanding with some 400 grit and the hood will be done and ready for sealer at the paint shop. Attach file:   (83.15 KB) Posted on: 2013/3/11 22:11
	-BigKev 1954 Packard Clipper Deluxe Touring Sedan -> Registry | Project Blog 1937 Packard 115-C Convertible Coupe -> Registry | Project Blog

AL HIZER	Re: BigKev's 1954 Packard Clipper Deluxe Sedan	#1585
Just can't stay away Joined: 2012/9/18 11:37 Last Login : 2013/6/25 14:32 From TOLEDO OH 43604 Group: Registered Users Posts: 55	kev could you read my post and help me you have been verry helpful in the past thank you Posted on: 2013/3/12 7:14
	AL

BigKev	Re: BigKev's 1954 Packard Clipper Deluxe Sedan	#1586
Webmaster Joined: 2006/4/17 13:30 Last Login : Today 8:40 From North Aurora, IL Group: Webmasters Registered Users Posts: 12043	Sorry, not sure which post you are referring to?? Posted on: 2013/3/12 12:28
	-BigKev 1954 Packard Clipper Deluxe Touring Sedan -> Registry | Project Blog 1937 Packard 115-C Convertible Coupe -> Registry | Project Blog

BigKev	Re: BigKev's 1954 Packard Clipper Deluxe Sedan	#1587
Webmaster Joined: 2006/4/17 13:30 Last Login : Today 8:40 From North Aurora, IL Group: Webmasters Registered Users Posts: 12043	Sprayed some DTM Epoxy High Build on the hood side and bottom edges. I'll let that cure off till tomorrow and then block it down. Attach file:   (93.51 KB)   (96.66 KB) Posted on: 2013/3/12 21:35
	-BigKev 1954 Packard Clipper Deluxe Touring Sedan -> Registry | Project Blog 1937 Packard 115-C Convertible Coupe -> Registry | Project Blog

BigKev	Re: BigKev's 1954 Packard Clipper Deluxe Sedan	#1588
Webmaster Joined: 2006/4/17 13:30 Last Login : Today 8:40 From North Aurora, IL Group: Webmasters Registered Users Posts: 12043	More work in the garage tonight. Flipped the hood back over a spot primed a few spots were I burned throught with the rough blocking. This car has way to many edges! Then started the final blocking with the 400grit on a long board. Its really leveling out very nicely. No high or low spots, and being extra careful around the edges and body lines. No pics tonight as I am still in progress on it. Posted on: 2013/3/14 23:26
	-BigKev 1954 Packard Clipper Deluxe Touring Sedan -> Registry | Project Blog 1937 Packard 115-C Convertible Coupe -> Registry | Project Blog

Joseph Earl	Re: BigKev's 1954 Packard Clipper Deluxe Sedan	#1589
Home away from home Joined: 2012/2/14 19:27 Last Login : 3/21 19:00 From South Florida Group: Registered Users Posts: 556	Looking good, Kev! Posted on: 2013/3/16 14:09
	Joey (?=#=?) "If chrome got me home, I'd for sure still be stuck somewhere." [url=http://pac

BigKev	Re: BigKev's 1954 Packard Clipper Deluxe Sedan	#1590
Webmaster Joined: 2006/4/17 13:30 Last Login : Today 8:40 From North Aurora, IL Group: Webmasters Registered Users Posts: 12043	Thanks Joey! Worked on the car for about 8 hours yesterday. Blocked most of the car with 400 grit. Found a few areas that need attention and some high areas I need to work down and reprime. I can tell you after blocking for 8 hours, your arms nearly want to fall off, and you come out of the garage looking like casper. Posted on: 2013/3/18 11:33
	-BigKev 1954 Packard Clipper Deluxe Touring Sedan -> Registry | Project Blog 1937 Packard 115-C Convertible Coupe -> Registry | Project Blog