Re: Oil pick up on 1940 356 engine
|
||||
---|---|---|---|---|
Home away from home
![]() ![]() ![]() |
Hi Bill:
The sloshing is wrong. It should float on top of the oil. That is the primary filtration method. I would look for a better one. Then let it soak in a closed container of gasoline for a month. Probably what happened to yours is someone tried to burn the sludge out of the screen and melted the solder. Ideally they should replaced by a new one with a rebuild, but that is impossible. The hole in the middle of the screen precludes oil starvation.
Posted on: 2013/8/19 20:26
|
|||
|
Re: Oil pick up on 1940 356 engine
|
||||
---|---|---|---|---|
Home away from home
![]() ![]() ![]() |
Hi Tim, thanks. After reading your response I realized how obvious this should have been, a floating pick up is ideal for preventing settled solids (sludge) from entering the oiling ducts. Will look for another pick up assembly. Thanks again.
Bill
Posted on: 2013/8/19 22:43
|
|||
|
Re: Oil pick up on 1940 356 engine
|
||||
---|---|---|---|---|
Home away from home
![]() ![]() ![]() |
Hi Tim, I have to ask, I assume the reason for soaking the strainer assembly for a month in gasoline is to dissolve any inside sludge and to see if the float chamber is sealed? Also, can't find the "hole" in the suction screen. The lower side and bottom does, however, have four elongated openings exposing the fine mesh screen. I wonder if this is the original part? This one is made by Taylor Sales and Engineering in Elkhart Indiana, model #13692339-1890964. Of course, this doesn't match the part # in the Packard Parts List manual. Hope I can find a "floating" replacement or will have to take suction from the bottom and change the oil very often (engine does have a bypass filter). It looks like there was a repair made as there is a large glob of solder on the top near the center?
Bill
Posted on: 2013/8/20 11:15
|
|||
|
Re: Oil pick up on 1940 356 engine
|
||||
---|---|---|---|---|
Home away from home
![]() ![]() ![]() |
It sounds like your float camber has a leak and has partly filled with liquid. The suction tube and screen should be free draining.
Best to look for a replacement Taylor was the original supplier of this part and the float came with the blob of solder on top. Not sure about 1940, but the lower shield has 4 tabs that are crimped in place for 1948, not soldered.
Posted on: 2013/8/20 14:15
|
|||
|
Re: Oil pick up on 1940 356 engine
|
||||
---|---|---|---|---|
Home away from home
![]() ![]() ![]() |
i believe max merrett can supply one
Posted on: 2013/8/20 19:59
|
|||
35-1200 touring sedan 42-110 convertible coupe 48-2293 station sedan |
||||
|
Re: Oil pick up on 1940 356 engine
|
||||
---|---|---|---|---|
Home away from home
![]() ![]() ![]() |
If you take the cover off, there should be a hole in the center of the screen. The metal plate prevents sucking foam the same way as a windage tray.
Posted on: 2013/8/20 21:04
|
|||
|
Re: Oil pick up on 1940 356 engine
|
||||
---|---|---|---|---|
Home away from home
![]() ![]() ![]() |
Thanks,found a replacement that floats! Trying to repair flooded pick up and keep it as a backup. Removed solder from top to open small drain hole and removed shield from bottom. The 4 tabs holding the shield on were soldered on as well as being crimped. Maybe soldering the tabs broke the solder between what appears to be the two halves of the pick up? Is there a way to remove the screen so I can check and re-solder the edge joint around the edge of the pick up?
Posted on: 2013/9/11 22:07
|
|||
|