Re: Removing Temperature Gauge from dash
|
||||
---|---|---|---|---|
Home away from home
|
The easiest way is to remove the dash, and put it on the work bench. I did that on my 39, and it allowed me to repair the damaged temp gauge, re-wood grain the dash, repaint the accent on the chrome and generally clean things up. But it you don't want to do that, remove the front seat and get under the dash with a good flashlight. The gauges unbolt from the back and can be removed. Just take photos so that you can remember how to put it back in. I posted a thread a year or so ago on repairing the temp gauge - it can be done if you have the right tools. I've done several gauges that way successfully. Let me know if you need some photos of the housing - I have some leftover parts from mine.
Posted on: 2014/8/4 23:01
|
|||
|
Re: Removing Temperature Gauge from dash
|
||||
---|---|---|---|---|
Home away from home
|
Thank you David, I appreciate your help
Posted on: 2014/8/5 11:00
|
|||
|
Re: Removing Temperature Gauge from dash
|
||||
---|---|---|---|---|
Home away from home
|
Checked my old gauges - 3 nuts hold the gauge cluster in. Easy to get out, a bit harder to get back in. Be sure to disconnect the power as Murphy ensures that you will touch the wrong wire at the wrong time, causing you to flinch at the bright spark and smoke, snapping your head back and smacking it on some miscellaneous sharp object that you though you had removed. This will ensure that your children will get time out in school for talking like Daddy.
Posted on: 2014/8/5 16:09
|
|||
|
Re: Removing Temperature Gauge from dash
|
||||
---|---|---|---|---|
Home away from home
|
Thank you again David for your reply. It sure is much tighter under the dash than I would have thought for a 1937 automobile. Many Thanks !!!
Posted on: 2014/8/5 21:40
|
|||
|
Re: Removing Temperature Gauge from dash
|
||||
---|---|---|---|---|
Just can't stay away
|
Corsa 7,
If it's set up like a 15th series 120 the lead runs up the firewall (inside, but under the firewall pad). It's not easy, but if You take the floor board & toe board out and go from underneath it's easier. However if Your fortunate & flexible You may be able to get it done with just the seat removed ( probably the entire seat frame). I think there are one or two clamps that hold the lead to the FW. That necessitates removing the FW pad. I may have a photo of that area without the FW pad, if I do I'll send copy. Mr. Grubbs information is quite right. Good luck & stay flexible. Packard 385
Posted on: 2014/8/7 0:21
|
|||
|
Re: Removing Temperature Gauge from dash
|
||||
---|---|---|---|---|
Home away from home
|
Thank you, I'm down to removing the firewall pad but not sure how the button retainers release so I can remove the pad ? Are you familiar with how they are removed. Thank you Packard 385 for responding to my post.
Posted on: 2014/8/7 22:47
|
|||
|
Re: Removing Temperature Gauge from dash
|
||||
---|---|---|---|---|
Home away from home
|
If your pad retainer clips are like the ones on my 115C, then simply squeezing the ends that protrude into the engine side of the cowl wall and pushing them through to the inside of the passenger compartment will do the trick.
(o{}o)
Posted on: 2014/8/7 22:56
|
|||
We move toward
And make happen What occupies our mind... (W. Scherer) |
||||
|
Re: Removing Temperature Gauge from dash
|
||||
---|---|---|---|---|
Home away from home
|
O.K. I will try that tomorrow, I thought I looked today at the firewall to see if they were visible from the engine side but might have overlooked them. Thank you for your reply.
Posted on: 2014/8/7 23:17
|
|||
|
Re: Removing Temperature Gauge from dash
|
||||
---|---|---|---|---|
Just can't stay away
|
Corsa 7,
JW is correct about those clips, although later Packard used a composition rubber type & I think the "Service Bulletin" mentions them as a replacement for the metal squeez type. Sorry, I couldn't find any photos of the FW area with pad removed. Found a couple withpad on & acessories installed but I'm not too swift at loading photos in computer. Take a few pictures as You go it will help with reassembly. Do anything else in the area while You're doing it( it's a lot of work for one thing ). Above all stay flexible & calm, "Remember they said,This is supposed to be FUN ? Best of luck with the job ! Packard 385
Posted on: 2014/8/8 0:30
|
|||
|