Re: 1940 Custom Oil Canister and Low Compression
|
||||
---|---|---|---|---|
Home away from home
![]() ![]() ![]() |
I now have the proper oil canister, with the inlet in the bottom and am ready to re do the oil lines. As a refresher, my engine is original. So does not have the oil canister output to oil pan. What I am going to do is, as in the packard photo, run a line from the oil pump, to the galley, with a side line to and from the oil canister. See if this this is ok. I change the oil about every 500 miles so may not need the oil filter. It will be there for looks, and may actually filter some oil. So my question is, can too much oil go to the galley? As it will essentially get full flow from oil pump. There will be no dump to oil pan.
Thanks
Posted on: 2014/8/20 0:17
|
|||
|
Re: 1940 Custom Oil Canister and Low Compression
|
||||
---|---|---|---|---|
Home away from home
![]() ![]() ![]() |
might have better luck on the prewar forum.
Posted on: 2014/8/20 18:59
|
|||
|
Re: 1940 Custom Oil Canister and Low Compression
|
||||
---|---|---|---|---|
Home away from home
![]() ![]() ![]() |
Trying to picture your oil filter tubing plumbing you are proposing, and don't understand it.
Why don't you plumb it the conventional way with a pressure line feeding the oil filter and a drain line back into the crankcase? The drain line can go into the pan via the bottom of the oil fill tube. Not a very elegant way to do it, but just as functional as the later crankcase method. Be careful that you are not taking flow and pressure away from the lifters. Some kind of restriction in the filter feed is needed. Oil filters on these 356 engines have been discussed many times. A good idea would be for you to do a search to get information on these installations. I hope this helps. (o{}o)
Posted on: 2014/8/20 23:01
|
|||
We move toward
And make happen What occupies our mind... (W. Scherer) |
||||
|
Re: 1940 Custom Oil Canister and Low Compression
|
||||
---|---|---|---|---|
Home away from home
![]() ![]() ![]() |
Sorry this ended up in post war. My thinking is, and perhaps wrong, that since there will be a direct line from output to galley, and a second through the filter, then back to galley, that the restriction will be the oil filter itself, causing the direct line to flow more, but if not then it is fed from the output of the filter. It is the same as the conventional way for the later engines, except instead of the filter output going to the oil pan, it feeds the galley along with the direct line.
I hesitate to drill and tap holes in the side of this original block. I am wondering if I do this it will cause too much oil or pressure to the galley? I have been told that these engines were originally shipped from factory without filters. Had simply a direct line from oil output to galley. Sometimes filters installed by dealers, and sometimes not. Thanks for your patience.
Posted on: 2014/8/21 0:09
|
|||
|
Re: 1940 Custom Oil Canister and Low Compression
|
||||
---|---|---|---|---|
Forum Ambassador
![]() ![]() ![]() |
I have been told that these engines were originally shipped from factory without filters.
That depends on which engine we're talking about. All 356 engines came from the factory with oil filters.
Posted on: 2014/8/21 0:50
|
|||
|
Re: 1940 Custom Oil Canister and Low Compression
|
||||
---|---|---|---|---|
Home away from home
![]() ![]() ![]() |
Thanks for that information. What are you doing up this late? Especially for an east coaster.
Posted on: 2014/8/21 1:06
|
|||
|
Re: 1940 Custom Oil Canister and Low Compression
|
||||
---|---|---|---|---|
Home away from home
![]() ![]() ![]() |
Went back to the beginning of the thread and now I am really confused. What are your reasons for changing any of the plumbing? Are the lifter noisy? If you plumb the engine so there are two paths to the lifter gallery the one with the filter will not flow significantly.
Posted on: 2014/8/21 4:34
|
|||
|
Re: 1940 Custom Oil Canister and Low Compression
|
||||
---|---|---|---|---|
Home away from home
![]() ![]() ![]() |
Yes lifters noisy after engine warm. If not much flow through filter, I believe ok, because change oil every four or five hundred miles or so. I believe I just want to make sure there is not too much pressure or oil to galley. This is an original 1940 block, does not have the oil filter outlet to oil pan. Being original the oil filter outlet was the only way to get oil to the galley. In my thinking now there will be two ways, a direct line and from the oil filter.
Thanks
Posted on: 2014/8/21 8:25
|
|||
|
Re: 1940 Custom Oil Canister and Low Compression
|
||||
---|---|---|---|---|
Forum Ambassador
![]() ![]() ![]() |
I believe I just want to make sure there is not too much pressure or oil to galley
That comment really has me flabbergasted. Just what is the actual oil pressure, road speed and hot idle? Can't say I ever heard of wanting to reduce the pressure to the oil galley unless the cold engine pressure was way above the spec, like significantly more than 40 or 45 psi and that would be done by adjusting the oil pressure relief valve on the pump body. BTW, is this a 356 engine?
Posted on: 2014/8/21 11:14
|
|||
|