Re: Over-Drive vs Gear Change for a '34 Coupe
|
||||
---|---|---|---|---|
Forum Ambassador
|
I've toured fairly extensively for decades in a '34 Eight sedan with the 4.69 rear axle. I've resisted either changing the rear axle ratio or adding overdrive; I like the lively around town performance it gives and great hill climbing with the 4.69; the downside is I have to behave myself and settle for 45-50 mph on highways. Assuming you're inclined to want faster highway speeds the choice will depend to some degree on what rear axle ratios you can get. With Phil Bray out of the scene, I don't know what's available in new gearsets. An original 4.07 set would be a nice choice. But IMO you'll get the most flexibility by retaining your 4.69 rear and installing an overdrive.
Posted on: 2016/11/7 17:35
|
|||
|
Re: Over-Drive vs Gear Change for a '34 Coupe
|
||||
---|---|---|---|---|
Home away from home
|
One of the problems with operating just about any PREwar car at high speeds of say 55 mph and faster is that curves in the road such as intercchaange ramps on the Interstate hiways may very well cause a terrific amount of body roll.
To sustain higher speeds (other than in a straight line) will probaby also require getting the suspension tied down. Perhaps just somespring loaded heavy duty shocks front and rear will help. I don't know. But whe nfirst operating the car with higher interstatee or open hiway speeds just be careful on curves and turns until the car proves itself. Probably need to set negative caster to the front suspension instead of the oem spec possitive caster. Check to see what the lowest ratio axle that is availaable. The car should have more than enuf low end power to never notice the difference. I'm running a 48 motorcycle with 4-1/2 stroke (1200cc) a 3 speed trans and i'm running 3 teeth over stock on the trans sprocket so i can keep up with my friends riding new Harleys. I barely notice the difference at low speeds at all nor even on steep hills that are graveel. If i could get a 28 tooth in under the chain gaurd i would do it in a heart beat. Or go with the overdrive. There is nothing worse than to become a moving obstacle out on the hiway.
Posted on: 2016/11/7 19:38
|
|||
VAPOR LOCK demystified: See paragraph SEVEN of PMCC documentaion as listed in post #11 of the following thread:f
packardinfo.com/xoops/html/modules/newbb/viewtopic.php?topic_id=7245 |
||||
|
Re: Over-Drive vs Gear Change for a '34 Coupe
|
||||
---|---|---|---|---|
Home away from home
|
There shoud be no reason that even something on the order of a 2.98 rear axle would just fine.
I had a 53 ford 6 cylinder with 2.98 rear axle and a 3 speed. NO problems.
Posted on: 2016/11/7 19:41
|
|||
VAPOR LOCK demystified: See paragraph SEVEN of PMCC documentaion as listed in post #11 of the following thread:f
packardinfo.com/xoops/html/modules/newbb/viewtopic.php?topic_id=7245 |
||||
|
Re: Over-Drive vs Gear Change for a '34 Coupe
|
||||
---|---|---|---|---|
Home away from home
|
A 2.98 axle is about 2/3 the current ratio, clearly unreasonable. Comparing a 50's Ford Six and a '48 motorcycle with a '34 Packard is more than ludicrous.
Posted on: 2016/11/7 20:12
|
|||
|
Re: Over-Drive vs Gear Change for a '34 Coupe
|
||||
---|---|---|---|---|
Forum Ambassador
|
Fully agree with Fred, 2.98 would give a very unacceptable result.. Some of these cars approach 4500 lbs and are driven thru fairly large 17 inch tires with but 120 horsepower. I've driven a 34 Eight sedan with a 3.98 and even modest upgrades that I would have sailed over in high gear required downshifting.
Now the coupe is one of the lighter body styles and might be a decent tourer with a 3.98 or thereabouts, but not a 2.98.
Posted on: 2016/11/7 20:23
|
|||
|
Re: Over-Drive vs Gear Change for a '34 Coupe
|
||||
---|---|---|---|---|
Quite a regular
|
Hi Tom:
As Owen correctly points out, those old "long-stroke" motors with that absurdly low gearing, combined with original-style "poured babbit" connecting rod bearings most certainly should not be driven over 45-50 mph. In the old days we'd go hunt in wrecking yards for wrecked '35 or later pre-war Packards to get the con-rods out of them. Their connecting rods ARE set up for "insert" style connecting rod bearings. You may have heard about the famous test Packard did when introducing their 1935 line - they took a "bone stock" STANDARD eight and drove it wide open ( around 90 mph) for 25,000 mi. with no significant wear ( on disassembly, they said "the car could have been re-assembled and run that test again...!). However, even tho an "insert rod bearing" equipped pre-war Packard CAN be driven that hard and that fast and that long, it is not a pleasant experience to have a motor spinning that fast. I agree with Owen - leave your rear axle gearing alone. Let's be realistic - your Standard Eight is MANY cubic inches of engine displacement smaller than the "big" Packards...so you don't have the raw torque to handle much higher rear axle ratios. So - either keep your speed down the way Owen recommends, or get an over-drive - Gear Vendors, for example, is one brand my friends have had good luck with. Once you get an overdrive, the difference in comfort will astound you as you glide over the countryside at 70 mph while everything forward of the rear axle output shaft thinks it is doing 48 mph...! As far as handling goes, be assured pre-war Packards are superb handlers. I have no idea why "Packard V8" made the statements he did about "curves in the road" - he is obviously ignorant of what it is like to drive a PROPERLY maintained pre-war Senior Packard at extreme speeds. IF PROPERLY maintained, the pre-war Packards are SPORTS CARS when compared with the post-war Packards. Let's discuss your pre-war Packard for what it IS. A superbly engineered driver that was in keeping with the Packard legend we are so proud of. Your Packard came with excellent shock absorbers. Are they filled with hydraulic fluid and otherwise doing the outstanding job they were engineered for ? Your Packard came with outstanding brakes. Yes, as a Packard lover, it is disappointing to me to drive a pre-war "rope-brake" equipped Packard that has NOT been properly maintained. Maybe that's the problem with "Packard V8"...maybe he got a ride in and/or drive some "costume jewelry" pre-war Packard, with all that implies in terms of terrible-to-truly frightening mechanical condition. Again..PROPERLY maintained.... you make a panic stop with your pre-war Packard and you may put un-belted passengers thru your windshield! Bottom line - listen to Owen !
Posted on: 2016/11/7 20:47
|
|||
|
Re: Over-Drive vs Gear Change for a '34 Coupe
|
||||
---|---|---|---|---|
Home away from home
|
Thanks Packard V8, appreciate all the input.
Regards, Tom
Posted on: 2016/11/7 21:19
|
|||
|
Re: Over-Drive vs Gear Change for a '34 Coupe
|
||||
---|---|---|---|---|
Home away from home
|
What is the over drive ratio to be used???
AND, what was the LOWEST ratio offered from the factory for the 34 in question??? We'll do some math.
Posted on: 2016/11/7 21:29
|
|||
VAPOR LOCK demystified: See paragraph SEVEN of PMCC documentaion as listed in post #11 of the following thread:f
packardinfo.com/xoops/html/modules/newbb/viewtopic.php?topic_id=7245 |
||||
|
Re: Over-Drive vs Gear Change for a '34 Coupe
|
||||
---|---|---|---|---|
Home away from home
|
Thank you Shinyhubcap ! I am taking your and O.D.'s advice on this for sure. You fellows have the experience and knowledge I lack, and I intend to put your input to work. This is the information I was hoping for....I also understand a good bit of it...for once ! :)
Thanks again. PS: Re The Shocks....I need a complete lesson on those too. To be honest, I don't even know where to find them...(I know, up front by the wheels !, but the shop that is bringing it all back to life just advised they filled them with fluid. The car has been laid up for years, and while the fellow I bought it from did some work on it, it seems he missed the shocks, or they are leaking like mad. How do I test them and what else should I be looking for in that area ? Thanks, Tom
Posted on: 2016/11/7 21:31
|
|||
|