Re: 35 motor mount
|
||||
---|---|---|---|---|
Forum Ambassador
![]() ![]() ![]() |
Just as an aside, as there were 4 different car lines in 1935, being more specific about which one can be important - I'm guessing it's a 1200-01-02.
The front motor mount is under the water pump and the rear mounts are on the transmission, what you're missing is a stabilizer. Not sure about '35 but thru '34 there was also one on the driver's side, though very different in construction. I'd take some photos of the 34 stabilizers but BDC has a '35 so perhaps he can snap some photos for you, I'd have to go to the parts book to see if both years were the same though I believe they were.
Posted on: 2017/2/8 18:57
|
|||
|
Re: 35 motor mount
|
||||
---|---|---|---|---|
Home away from home
![]() ![]() ![]() |
I hope this helps. On the 1935 1201 eight there is only one torque mount and it is located on the right side of the engine. It looks like you are missing the bracket that bolts to the gearbox and the torque mount. Kanter reproduces the torque mount. I have seen the brackets on eBay in the past, I bet Kanter will have that too.
Andy
Posted on: 2017/2/9 0:02
|
|||
|
Re: 35 motor mount
|
||||
---|---|---|---|---|
Home away from home
![]() ![]() ![]() |
Andy you got ahead of me. Here are 2 pictures of my 2 "parts cars" so they're not as pretty as Andy's.
Posted on: 2017/2/9 8:57
|
|||
I can explain it to you but I can't understand it for you
![]() Bad company corrupts good character! Farming: the art of losing money while working 100 hours a week to feed people who think you are trying to kill them |
||||
|
Re: 35 motor mount
|
||||
---|---|---|---|---|
Forum Ambassador
![]() ![]() ![]() |
BDC, do the '35 Eights have the fore-to-aft stabilizer on the driver's side? Looks a bit like a dog bone, split down the middle, that clamps over two rubber-covered ball sockets, one on the engine and the other on the frame. Maybe I can get a picture of it later today.
Posted on: 2017/2/9 10:09
|
|||
|
Re: 35 motor mount
|
||||
---|---|---|---|---|
Home away from home
![]() ![]() ![]() |
Here's the drivers side O_D.
Posted on: 2017/2/9 10:44
|
|||
I can explain it to you but I can't understand it for you
![]() Bad company corrupts good character! Farming: the art of losing money while working 100 hours a week to feed people who think you are trying to kill them |
||||
|
Re: 35 motor mount
|
||||
---|---|---|---|---|
Home away from home
![]() ![]() ![]() |
I have sent a "PM" regarding your parts on the parts cars
Posted on: 2017/2/9 17:15
|
|||
|
Re: 35 motor mount
|
||||
---|---|---|---|---|
Forum Ambassador
![]() ![]() ![]() |
Pix of the driver's side fore-to-aft motor stabilizer as installed on 1100-01-01; Super Eight and '33 and '32 may be the same, unsure if they were used post 1934. Would have been a more informative pix if taken from below but it's about 20? F in the garage today.
The piece is immediately adjacent and to the left of the spring, painted black, two mirror-image halves in the form of a dog bone, fastens over two ball studs, one attached to the rear of the motor and the other to the frame. Ball studs themselves are covered with a rubber boot. The two halves are held by nut and bolt thru the halves at each end. EDIT: BDC, looking more closely at your photo in #6 above, your 1201 does indeed have the fore-to-aft stabilizer link just as shown for the '34.
Posted on: 2017/2/10 11:29
|
|||
|
Re: 35 motor mount
|
||||
---|---|---|---|---|
Just can't stay away
![]() ![]() ![]() |
Thanks for the feedback, I'll contact KAntner and MAx and see if they have anything available...
Posted on: 2017/2/10 14:18
|
|||
ClassicCrusier
|
||||
|