EE-22 Question
|
||||
---|---|---|---|---|
Forum Ambassador
![]() ![]() ![]() |
I have asked by one of our club members to look at some EE-22 carbs on his behalf. What do the experienced here advise I should be looking for in particular, in checking these over?
Posted on: 2020/7/2 5:59
|
|||
Mal
/o[]o\ ==== ![]() Bowral, Southern Highlands of NSW, Australia "Out of chaos comes order" - Nietzsche. 1938 Eight Touring Sedan - SOLD 1941 One-Twenty Club Coupe - SOLD 1948 Super Eight Limo, chassis RHD - SOLD 1950 Eight Touring Sedan - SOLD What's this? ![]() Put your Packard in the Packard Vehicle Registry! Here's how! Any questions - PM or email me at ozstatman@gmail.com |
||||
|
Re: EE 22 Question
|
||||
---|---|---|---|---|
Home away from home
![]() ![]() ![]() |
What is the question?
Posted on: 2020/7/2 8:25
|
|||
|
Re: EE 22 Question
|
||||
---|---|---|---|---|
Home away from home
![]() ![]() ![]() |
OD's right about the inlet. When i work on one of these i figure im working with glass.
The Fuel Pump to Carb TUBE will put strain and vibration on the Inlet. Suggest a 3"lg Fuel Line Hose b installed between the two. Theres getting to b less Bowls available so treat them as Gold Glass.
Posted on: 2020/7/2 10:33
|
|||
|
Re: EE 22 Question
|
||||
---|---|---|---|---|
Forum Ambassador
![]() ![]() ![]() |
![]() Concerning the type of EE-22, I'm told it's to replace one on a '35 Super Eight with 1 & 3/16" diameter throttle(correct term?) bore size. The carbs I'll be inspecting were owned by a guy with '35 and '36 Packards and believe these were spares he collected over the years. Besides the EE-22 mark, are there any other markings that will help me in identification?
Posted on: 2020/7/2 14:47
|
|||
Mal
/o[]o\ ==== ![]() Bowral, Southern Highlands of NSW, Australia "Out of chaos comes order" - Nietzsche. 1938 Eight Touring Sedan - SOLD 1941 One-Twenty Club Coupe - SOLD 1948 Super Eight Limo, chassis RHD - SOLD 1950 Eight Touring Sedan - SOLD What's this? ![]() Put your Packard in the Packard Vehicle Registry! Here's how! Any questions - PM or email me at ozstatman@gmail.com |
||||
|
Re: EE 22 Question
|
||||
---|---|---|---|---|
Forum Ambassador
![]() ![]() ![]() |
Unless there was some sort of manifold swap, for that car you should be looking for an EE-23, not an EE-22. BIG difference.
The proper terminology is venturi size or diameter rather than bore. For the EE-22 used only in 1933/1934 the Super Eight venturi is 1-3/16, Eight is 1-3/32 and I assume the same for the EE-23s used in 1935/1936. I've posted here quite a few times a chart from an old Chilton's which gives the specs and various component part numbers for many of the Strombergs used by Packards. You should be able to find it with a simple search but if not, let me know and I'll get to my PC and dig it out again. It's on yellow paper.
Posted on: 2020/7/2 15:00
|
|||
|
Re: EE 22 Question
|
||||
---|---|---|---|---|
Home away from home
![]() ![]() ![]() |
Another little TIDPIT: Ive ran 1-3/32 on su8s and 1-3/16 on 8s and cant tell the diff. Would guess PACKARD went with their standard theory - every model should have a diff size weather they need it or not.
Posted on: 2020/7/3 10:22
|
|||
|
Re: EE-22 Question
|
||||
---|---|---|---|---|
Home away from home
![]() ![]() ![]() |
Good afternoon...Wow, if you are correct, all of the different non-essential parts would certainly raise your costs and lower your profits...I should think...Ernie in Arizona
Posted on: 2020/7/3 17:01
|
|||
Caretaker of the 1949-288 Deluxe Touring Sedan
'Miss Prudence' and the 1931 Model A Ford Tudor 'Miss Princess' ![]() |
||||
|
Re: EE-22 Question
|
||||
---|---|---|---|---|
Forum Ambassador
![]() ![]() ![]() |
Well, I once had an EE-23 with an EE-22 bowl. Maybe I still have it. Seriously, Mal, I've got a couple 23's, 3/32.
Who's looking? (LF?)
Posted on: 2020/7/3 21:25
|
|||
|
Re: EE-22 Question
|
||||
---|---|---|---|---|
Forum Ambassador
![]() ![]() ![]() |
David,
Never know, there could have been some "swapsie" of parts along the way or even an entire carburettor! And no, not LF, but the guy whose '35 Coupe Wade worked on. You would know the car as it was in NZ for the Warbirds Rally a couple of years back. Going to look at the carbs tomorrow morning, so should know more then. On the way home am meeting with a guy whose uncle was a early Packard aficionado here, to get a story/stories for our club magazine.
Posted on: 2020/7/3 22:02
|
|||
Mal
/o[]o\ ==== ![]() Bowral, Southern Highlands of NSW, Australia "Out of chaos comes order" - Nietzsche. 1938 Eight Touring Sedan - SOLD 1941 One-Twenty Club Coupe - SOLD 1948 Super Eight Limo, chassis RHD - SOLD 1950 Eight Touring Sedan - SOLD What's this? ![]() Put your Packard in the Packard Vehicle Registry! Here's how! Any questions - PM or email me at ozstatman@gmail.com |
||||
|