|
Re: RIk's 56 ultramatic
|
||||
|---|---|---|---|---|
|
Home away from home
 
|
NApa sender works. For how long ?
Had to use street 90s This delco distributor. Oil tube the curve is to wide
Posted on: 2021/11/13 0:26
|
|||
|
Riki
|
||||
|
||||
|
Re: RIk
|
||||
|---|---|---|---|---|
|
Home away from home
|
Ready for testing.
Still need to make up the relays. Attach file:  20211116_184934_HDR.jpg (254.44 KB) 20211116_184922_HDR.jpg (216.56 KB) 20211116_184956_HDR.jpg (194.12 KB)
Posted on: 2021/11/16 22:40
|
|||
|
Riki
|
||||
|
||||
|
Re: RIk
|
||||
|---|---|---|---|---|
|
Home away from home
|
Another done.
Smooth.. To get window out. Stuck up. Remove regulator bolt and unscrew motor. Motor / regulator will drop down. Then you can get to window clips. Packard motor shorted .. Attach file: 20211119_153532_HDR.jpg (271.60 KB) 20211119_153419_HDR.jpg (225.54 KB) 20211119_153302_HDR.jpg (144.86 KB) 20211119_153247_HDR.jpg (263.79 KB)
Posted on: 2021/11/19 19:49
|
|||
|
Riki
|
||||
|
||||
|
Packard 12 rod beating inserts
|
||||
|---|---|---|---|---|
|
Home away from home
|
Drilling holes for new bearings
Bottom picture is new rod and insert I drilled. New rods holes are in center of rod. The small hole is 60 degrees off center. The jig. I think my dad made for getting Babbitt off of copper. Still need to put a fillet on the little hole Attach file: 20211128_193830_HDR.jpg (240.85 KB) 20211128_193919_HDR.jpg (184.18 KB) 20211128_193928_HDR.jpg (176.17 KB) 20211130_115356_HDR.jpg (204.08 KB) 20211130_115409_HDR.jpg (234.10 KB) 20211130_192930_HDR.jpg (176.78 KB)
Posted on: 2021/12/1 15:41
|
|||
|
Riki
|
||||
|
||||
|
Re: Packard 12 rod beating inserts
|
||||
|---|---|---|---|---|
|
Forum Ambassador
 
|
Here is the photo with sender trunk hole dimensions Ross provided and is applicable 51-56.
Attach file: 51-6 trunk opening dimensions1.jpg (133.64 KB)
Posted on: 2021/12/1 17:06
|
|||
|
Howard
|
||||
|
||||
|
Re: RIk's 56 ultramatic
|
||||
|---|---|---|---|---|
|
Home away from home
|
Thanks h.
Posted on: 2021/12/1 17:11
|
|||
|
Riki
|
||||
|
||||
|
Re: RIk
|
||||
|---|---|---|---|---|
|
Home away from home
|
Attach file: 20211222_190903.jpg (213.42 KB)
Posted on: 2021/12/22 23:19
|
|||
|
Riki
|
||||
|
||||
|
Re: RIk
|
||||
|---|---|---|---|---|
|
Home away from home
|
Lower A arm
I know they were my camber problem. Now to get them out. Can't press them out. It was my squeak too. Inner but was loose. Attach file: 20220212_132926.jpg (158.97 KB) 20220212_130125.jpg (390.23 KB)
Posted on: 2022/2/12 16:39
|
|||
|
Riki
|
||||
|
||||
|
Re: RIk
|
||||
|---|---|---|---|---|
|
Quite a regular
 
|
if the axle is moving, you can get the bush out with crowbar.
Posted on: 2022/2/14 7:15
|
|||
|
||||
