Packard Forum Index » Project Blogs

Topic: Stewart's 1955 Packard 400

Bottom

Previous Topic

Next Topic Register To Post

« 1 ... 98 99 100 (101) 102 103 104 ... 160 »

R H

Re: Stewart's 1955 Packard 400

#1001

Home away from home

At least yours will be a tight fit.

Posted on: 2022/9/19 21:11

Riki

jfrom@kanter

Re: Stewart

#1002

Home away from home

Quote:

Cli55er wrote:
gasket fit my windshield fine. it just wasn't wide enough to fit in the opening and capture the glass at the same time. it would either sit on the glass or sit on the lip of the metal...but not both correctly. the second gasket was a bit better, but not perfect and i was tired of jacking with them...so i siliconed it all up.

basically one of two thoughts...either the gasket wasn't right....or the opening in the car grew by itself magically...top to bottom. the window would sit on the bottom lip of the metal fine, but in doing so the top lip was not captured by the gasket. the gasket wasn't thick enough...plain and simple. garbage, but i made it work.

The 55-56 have a tendency to have to front/rear windshield openings "grow" due to rusting of the rear trunk area/body mounts area and the rear body sagging which causes the openings to open up. We had a car in our shop that had the original windshield and a 1/8" gap between the top of the windshield and the gasket. It had broken trunk floor in the area of the body mounts

James From
Kanter Auto Products

Posted on: 2022/9/20 6:15

Cli55er

Re: Stewart

#1003

Forum Ambassador

No such rust on my car. So have no clue. Body mounts are new as well. window fit fine when I removed it.

Posted on: 2022/9/20 15:43

1937 Packard 138-CD Deluxe Touring Limousine
Maroon/Black 1090-1021
[url=https://packardinfo.com/xoops/html/modules/registry/View.php?ID=232]1955 Packard

Stewart Ballard

Re: Stewart

#1004

Home away from home

Tried putting the chrome across the top of the rear windshield tonight. It was not too bad since the glass is sitting on a table. However, I started on one side and went across. When I got to the other end I have an extra inch of chrome.
The groove in a seal stops about an inch from the bottom on both sides.
I checked under the two connecting pieces across the top and there is no space left in either one to shorten it.
I wonder if I got the front piece mixed up with the rear. Will have to check that out tomorrow.

Attach file:

20220926_153728_resized.jpg (118.91 KB)

20220926_153703_resized.jpg (104.60 KB)

20220926_153742_resized.jpg (115.89 KB)

Posted on: 2022/9/26 18:35

Stewart Ballard

Pgh Ultramatic

Re: Stewart's 1955 Packard 400

#1005

Home away from home

Oh that's just part of the experience

I would check that but I honestly wouldn't even be surprised...

Everything "windshield" on these is such a pain.

Posted on: 2022/9/26 19:10

Stewart Ballard

Re: Stewart

#1006

Home away from home

I am looking forward to the challenge....no I am not.

There is no way to confuse the front and back windshield chrome. They are very different.

I guess the groove on the original seal did not stop an inch above the bottom.
I don't see any way to overlap the sections under the connectors so I am toying with the idea of trimming the section that is circled on both ends. The lower chrome should hide most of it.

Attach file:

20220927_114056_resized (2).jpg (55.50 KB)

Posted on: 2022/9/27 11:00

Stewart Ballard

Marty or Marston

Re: Stewart's 1955 Packard 400

#1007

Home away from home

Before cutting you might want to double or triple check the size of the glass and rubber seal versus the size of the opening. If I recall correctly, the glass for a '55 convertible is 1" narrow than a hardtop.

Remember the old adage "Measure twice, cut once".

Posted on: 2022/9/27 15:43

Marty
Big Sister
Little Sister (SOLD)
Baby

Owen_Dyneto

Re: Stewart's 1955 Packard 400

#1008

Forum Ambassador

Marty, the difference in the convertible windshields is about 2 inches.

Posted on: 2022/9/27 15:54

Stewart Ballard

Re: Stewart's 1955 Packard 400

#1009

Home away from home

This is the original rear windshield that I removed myself. Only the seal is modern.

The new front windshield is still in the box as I do not have a seal for it yet.

Posted on: 2022/9/27 18:55

Stewart Ballard