Re: 1934 1104 Transmission Removal and Clutch replacement
|
||||
---|---|---|---|---|
Just can't stay away
![]() ![]() ![]() |
Thank you for all your help, tomorrow my friend and I are going to try to get the heavy trans out.
Roberto
Posted on: 2013/1/14 22:57
|
|||
cityvintage@hotmail.com
Purveyors of men's vintage clothing 1900-1960's |
||||
|
Re: 1934 1104 Transmission Removal and Clutch replacement
|
||||
---|---|---|---|---|
Just can't stay away
![]() ![]() ![]() |
Hello,
When I look underneath I see two side motor mounts that are attached to the engine and frame, would this not support the engine when I remove the transmission? Please help
Posted on: 2013/1/15 18:42
|
|||
cityvintage@hotmail.com
Purveyors of men's vintage clothing 1900-1960's |
||||
|
Re: 1934 1104 Transmission Removal and Clutch replacement
|
||||
---|---|---|---|---|
Just can't stay away
![]() ![]() ![]() |
Hello,
reading the service letters it makes reference to the special adapter tool designed to use on the standard for holding the engine while the transmission is out, but this is the 10th series does the 11th series need this if it has rear side mounts on each side. I am little confused. Thank you Roberto
Posted on: 2013/1/15 19:23
|
|||
cityvintage@hotmail.com
Purveyors of men's vintage clothing 1900-1960's |
||||
|
Re: 1934 1104 Transmission Removal and Clutch replacement
|
||||
---|---|---|---|---|
Just can't stay away
![]() ![]() ![]() |
That's what I figured, I am designing a wood brace at rear made out of two by fours to support engine on case at rear with floor jack help. This looks like it would work.
Thank you for the quick reply. Roberto...
Posted on: 2013/1/15 20:27
|
|||
cityvintage@hotmail.com
Purveyors of men's vintage clothing 1900-1960's |
||||
|
Re: 1934 1104 Transmission Removal and Clutch replacement
|
||||
---|---|---|---|---|
Just popping in
![]() ![]() ![]() |
Hi Roberto
I’m wondering if your transmission removal was successful (?). Did you make an engine support tool with two by fours? I’m faced with ‘33 Super Eight transmission removal…(ring gear replacement)…. David Timberlake Maybe this could be adapted to be like the Tool ST-919 motor support… ….I’m thinking 1) turn it upside down 2) maybe too long—so may need to be cut.. ….ST-919 cost $8 in 1933….four times the cost of this one in current dollars. Engine Support Bar Engine Hoist Load Leveler Picker Shop Crane Load Lift Tool—-$55 ebay.com/itm/196068853353?_skw=engine+support+tool&itmmeta=01JZAZMEW8NEGKZTXEMZ083XPJ&hash=item2da69d4669:g:WkYAAOSwr6ZoMDJ3&itmprp=enc%3AAQAKAAAA0FkggFvd1GGDu0w3yXCmi1fTCuHpLmzbUbNl4p8LnNlbJoz6EMf7rubHfS8rXavD4ALxRC9cZJ%2FRtRH7h84MS7v1oTitvSgEubi9u9WBt8YE645cgzBeYtSSFcQg7rZTAUAlnUmqNbgDBKcl0TKrKqJBYsxqX7SXoX5g3FCrPjJq0aMS6vp1poPkOW27ZMNkrCzDV1%2BBsRmk50fvXTwM4UvdXHJcSSNWw3K1sKpQPYaV%2Frv08gBS%2FCTwlnT%2B%2Bo5rBRTzG6KfyF%2FEIniyN5Zk--w%3D%7Ctkp%3ABk9SR7Lu0d_6ZQ..
Posted on: Today 11:26
|
|||
|