Happy Easter and welcome to Packard Motor Car Information! If you're new here, please register for a free account.  
Login
Username:

Password:

Remember me



Lost Password?

Register now!
FAQ's
Main Menu
Recent Forum Topics
Who is Online
117 user(s) are online (73 user(s) are browsing Forums)

Members: 1
Guests: 116

Packard Don, more...
Helping out...
PackardInfo is a free resource for Packard Owners that is completely supported by user donations. If you can help out, that would be great!

Donate via PayPal
Video Content
Visit PackardInfo.com YouTube Playlist

Donate via PayPal



(1) 2 »

Normal Compression Test Values for 1931 Super 8
#1
Just can't stay away
Just can't stay away

Stephen Templeton
See User information
Can someone please point me to normal compression test values for a 1931 Packard 840 (super 8 engine)? I’ve seen a couple of forum posts on the internet suggesting 80-85 as normal, but I can’t find an official listing. Thanks!

Posted on: 2022/5/14 17:59
 Top  Print 
 


Re: Normal Compression Test Values for 1931 Super 8
#2
Forum Ambassador
Forum Ambassador

Owen_Dyneto
See User information
This should provide the answer.

Attach file:



jpg  Compression versus altitide.jpg (149.52 KB)
177_62803bdcd2a56.jpg 1245X815 px

Posted on: 2022/5/14 18:31
 Top  Print 
Like (1)
 


Re: Normal Compression Test Values for 1931 Super 8
#3
Home away from home
Home away from home

Packard Newbie
See User information
Dave, I'm surprised altitude has that much of an effect on compression?!!? It makes sense that it would have an effect - but a couple of thousand feet sure brings it down a notch! Chris.

Posted on: 2022/5/15 13:44
'If you think you can, or you think you can't - you're right!' Henry Ford.
1939 Packard Six, Model 1700
 Top  Print 
 


Re: Normal Compression Test Values for 1931 Super 8
#4
Home away from home
Home away from home

Tim Cole
See User information
The Packard manual specifies 85 psi through 1931. They raised it to 100 psi in 32.

Rule of thumb doesn't always work. For example, I had a modern car that always had 165-175 psi for 9.9:1 compression and the manual specified 200 and said anything below 180 was a sick engine. I bought the car new and the engine quit at 112,000. I later found out from an engineer that they were using junk rings for the American builds. The Mexican builds were going over 700,000. If only I was in California when I bought it!

Back to rule of thumb: Generally, an engine will lose 3% horsepower for every 1000 feet above sea level. Which always has me thinking about a publicity photo of a Packard 120 seven passenger fully occupied and climbing Pike's Peak. That means the car was only putting out 70 crankshaft horsepower at the summit. That picture has me thinking that all the overhauling in the world will not restore as new performance in old motors.

Posted on: 2022/5/15 14:38
 Top  Print 
Like (1)
 


Re: Normal Compression Test Values for 1931 Super 8
#5
Just can't stay away
Just can't stay away

Stephen Templeton
See User information
Thanks to all!
I’ve got problems- hopefully it’s just valves that can be adjusted, and cylinder 1 likely with a ring issue.

Attach file:



jpeg  DF770354-25C3-48CA-8647-8D55B812FFB0.jpeg (209.20 KB)
184962_6283818219a1d.jpeg 1440X1920 px

Posted on: 2022/5/17 6:05
 Top  Print 
 


Re: Normal Compression Test Values for 1931 Super 8
#6
Home away from home
Home away from home

Tim Cole
See User information
Looks like some stuck valves. Pull valve cover and check the action.

The one wet test indicates ring problems, but they may be stuck as well.

Posted on: 2022/5/17 7:23
 Top  Print 
 


Re: Normal Compression Test Values for 1931 Super 8
#7
Home away from home
Home away from home

Fish'n Jim
See User information
Not surprising if you think about it. You need oxygen above 10000 ft, so the ratio of fuel/air has to change going up. Planes adjust, cars aren't equipped but usually tuned for altitude if they reside at elevation.
The compression ratio isn't always correct. Best to calculate or measure as head space varies with design /overhaul. The L flat heads have a larger head space so lower compression by default.
Use it as a guide, if they're all over the map then there's problems, if fairly uniform, good to go. I would not get bent out of shape, if my numbers did match to book values, because you probably did not correct for air pressure, temperature, etc. which you need to do. Log what you got by vehicle and keep for reference next time.

Posted on: 2022/5/17 8:25
 Top  Print 
 


Re: Normal Compression Test Values for 1931 Super 8
#8
Just can't stay away
Just can't stay away

Stephen Templeton
See User information
I have lots of documentation on the car which was originally restored by Nethercutt around 1960- Here’s an Allen-Tronic evaluation that I believes dates to that period, although no specific date is listed. Page two lists compression test results at the time- mostly 60-65 psi, and check boxed “ok”-interesting.

Attach file:



jpeg  DF40ECE4-C08A-425C-9ED0-039B48DD1C50.jpeg (232.17 KB)
184962_6283c4d533bdf.jpeg 1440X1920 px

Posted on: 2022/5/17 10:52
 Top  Print 
 


Re: Normal Compression Test Values for 1931 Super 8
#9
Just can't stay away
Just can't stay away

Stephen Templeton
See User information
Page one of Allen-Tronic report

Attach file:



jpeg  C90973B0-C7A4-4037-9707-8B440A0346BA.jpeg (260.68 KB)
184962_6283c6018ec38.jpeg 1440X1920 px

Posted on: 2022/5/17 10:57
 Top  Print 
 


Re: Normal Compression Test Values for 1931 Super 8
#10
Just can't stay away
Just can't stay away

Stephen Templeton
See User information
I’m thinking about filling the zero compression cylinders with Marvel mystery oil or penetrating oil and letting them soak to see if I can get the stuck valves to loosen up. Any thoughts or recommendations?

Posted on: 2022/5/17 19:40
 Top  Print 
 




(1) 2 »




Search
Recent Photos
Photo of the Day
Recent Registry
Website Comments or Questions?? Click Here Copyright 2006-2024, PackardInfo.com All Rights Reserved