Happy Easter and welcome to Packard Motor Car Information! If you're new here, please register for a free account.  
Login
Username:

Password:

Remember me



Lost Password?

Register now!
FAQ's
Main Menu
Recent Forum Topics
Who is Online
111 user(s) are online (66 user(s) are browsing Forums)

Members: 3
Guests: 108

29tons, pmhowe, Karl, more...
Helping out...
PackardInfo is a free resource for Packard Owners that is completely supported by user donations. If you can help out, that would be great!

Donate via PayPal
Video Content
Visit PackardInfo.com YouTube Playlist

Donate via PayPal



« 1 2 3 (4) 5 6 7 ... 70 »

Re: RIk's 56 ultramatic
#31
Home away from home
Home away from home

64avanti
See User information
Very Pretty.
Tell me about your wiper motor please.

Posted on: 2014/7/20 10:28
 Top  Print 
 


Re: RIk's 56 ultramatic
#32
Home away from home
Home away from home

R H
See User information
64.

its a 55-56-57 chevy, have parking problems, i liked the vacuum better,

i had to make a spacer for it, where the cam is, there was like a 1/4 inch gap, when you put motor on fire wall,

Posted on: 2014/7/20 20:53
Riki
 Top  Print 
 


Re: RIk's 56 ultramatic
#33
Home away from home
Home away from home

R H
See User information
getting closer, the stainless exhaust pipes, from nc, driver side, goes down, i need to lift it up, pass side looks like its to long, and not the right bends, that goes for both pipes,

any that takes it back behind doors, and that is how much straight pipe i will have at start up, should sound nice,

going to have to put a jack under lower case, then will have to take it off when trans goes in, still waiting to get 2 rings ground, its only been a year and a half..........that has held me, up..

still need to make 2 alum brz, bushing for reactor shaft,,,lathe went down,,,,,,,,,,


i hope the pipes don't set with break in, i may block them , where they should be in cradle,,, have not finished exhaust hangers yet,,,,,

Attach file:



jpg  (70.23 KB)
4498_53cc736eb15e2.jpg 960X720 px

jpg  (53.19 KB)
4498_53cc7379e675f.jpg 960X720 px

Posted on: 2014/7/20 21:04
Riki
 Top  Print 
 


Re: RIk's 56 ultramatic
#34
Home away from home
Home away from home

R H
See User information
dads 56 Patrician

by,

ken yankee

Attach file:



jpg  (188.52 KB)
4498_54cc6ee12ea94.jpg 991X1280 px

Posted on: 2015/1/31 0:41
Riki
 Top  Print 
 


Re cam oil my fix
#35
Home away from home
Home away from home

R H
See User information
this my fix for oil lifter problem, oil, hole 7/64ths

Attach file:



jpg  (76.62 KB)
4498_558ede5ff04f7.jpg 832X468 px

Posted on: 2015/6/27 12:35
Riki
 Top  Print 
 


Re: RIk's 56 ultramatic
#36
Home away from home
Home away from home

R H
See User information
parking pawl,,,,,,needle,,,starting to put ultra together

Attach file:



jpg  (46.56 KB)
4498_55eca13574d51.jpg 780X439 px

jpg  (39.90 KB)
4498_55eca164a80e0.jpg 780X439 px

jpg  (46.38 KB)
4498_55eca1896f963.jpg 780X439 px

jpg  (57.54 KB)
4498_55eca1e3c2cf5.jpg 780X439 px

jpg  (16.13 KB)
4498_55eca1ffad733.jpg 520X293 px

Posted on: 2015/9/6 15:28
Riki
 Top  Print 
 


Re: RIk's 56 ultramatic
#37
Home away from home
Home away from home

R H
See User information
my dads fix,, lever

Attach file:



jpg  (42.70 KB)
4498_55ed3ada6f74b.jpg 780X439 px

jpg  (56.30 KB)
4498_55ed3afb0f48b.jpg 780X439 px

Posted on: 2015/9/7 2:20
Riki
 Top  Print 
 


Re: RIk's 56 ultramatic
#38
Home away from home
Home away from home

R H
See User information
band shafts,,grade 8 bolt,,low band,,, reverse band has 3/8 shaft, doing next...

spacers to center lever.,,,no groove in bolt, except at roll pin

Attach file:



jpg  (50.94 KB)
4498_55ee44752d65e.jpg 780X439 px

jpg  (59.25 KB)
4498_55ee447f23243.jpg 780X439 px

Posted on: 2015/9/7 21:14
Riki
 Top  Print 
 


Re: RIk's 56 ultramatic
#39
Home away from home
Home away from home

Ross
See User information
Now that is the way Packard should have done them. That groove that they put in the middle is the source of the breakage as those pins see high bending loads. Mistakes like that are the type made by young engineers. Mr Delorean?

Posted on: 2015/9/8 5:48
 Top  Print 
 


Re: RIk's 56 ultramatic
#40
Home away from home
Home away from home

R H
See User information
thanks ross,,,going to use chrome molly rod, for final .. the bolts I have ,,,there is a casting line,, much rather smooth all around.

Posted on: 2015/9/8 22:14
Riki
 Top  Print 
 




« 1 2 3 (4) 5 6 7 ... 70 »




Search
Recent Photos
Photo of the Day
Recent Registry
Website Comments or Questions?? Click Here Copyright 2006-2024, PackardInfo.com All Rights Reserved