Merry Christmas and welcome to Packard Motor Car Information! If you're new here, please register for a free account.  
Login
Username:

Password:

Remember me



Lost Password?

Register now!
FAQ's
Main Menu
Recent Forum Topics
Who is Online
52 user(s) are online (46 user(s) are browsing Forums)

Members: 3
Guests: 49

BigKev, 56Clippers, Packard5687, more...
Helping out...
PackardInfo is a free resource for Packard Owners that is completely supported by user donations. If you can help out, that would be great!

Donate via PayPal
Video Content
Visit PackardInfo.com YouTube Playlist

Donate via PayPal



(1) 2 3 »

Bucking Slightly at Cruising Speeds
#1
Home away from home
Home away from home

Joe
See User information
Hey all - wanted to get some takes on this. Had my 23rd series for its longest drive today since I've had it, about an hour and fifteen minutes. Mostly 50+ mph driving, about 86 outside. Not CONFIDENT on the engine temp, but stays about 5/8 of the way to H (I know, I need a proper gauge). A little background:

- 327 w/ Ultramatic
- Fuel: tank is brand new w/ vented cap; lines are relatively new, mechanical pump moving about 3.75 psi at idle, checked lines for leaks/kinks (possible air intrusion - nothing found). The carburetor (WDO 643-SA) has the float set per the Daytona rebuild kit instructions (3/16" w/ their float valve). Metering rods and and anti-percolator valves set per the Carter instructions (metering rods adjusted with the proper T109-113 tool).
- Spark: vacuum advance and distributor were rebuilt in the past 250 miles; plugs, wires, condenser, points, coil are all fairly new. Points gap set to .015". Car is 6v+. Initial timing verified at 7 degree.
- Intake: replaced oil bath filter with paper; no noticeable difference or performance; heat riser is free; no vacuum leaks found
- Exhaust: it's exhausting

The issue: after accelerating to cruising speed and I back off the pedal, 50 or so mph, the car has a tendency to buck somewhat. It's not aggressive, and it doesn't sound or feel exactly like the engine is actually cutting out, but feels like you're going over a wavy road. If I depress the accelerator, either a little or lot, the engine just goes and it all smooths out. It's not always there, but enough to be generally kind of annoying. It also only does this once it gets to operating temperature, but it's been an issue for a while. When the engine temp is below the halfway mark, operation is smooth at all speeds and conditions.

My question - is it something in the carburetor that can cause this issue (should I revisit the metering rods?), or is my transmission slipping? I don't know what the transmission (either in the high range or direct drive) would feel like if it was slipping. The transmission is in relatively rough shape compared to the other mechanical elements of the car - very leaky (I do verify it's full before every drive), and it has no low range (behaves like it's in neutral), so I would think it might be suspect, but I'm not sure.

Any thoughts on what I might be chasing here? Thanks in advance!

Posted on: 7/28 14:48
Joe B.
Greenville, NC
1950 Super Deluxe Eight Touring Sedan, Model 2302-5
327 w/ Ultramatic, 6v+
 Top  Print   
 


Re: Bucking Slightly at Cruising Speeds
#2
Home away from home
Home away from home

53 Cavalier
See User information
I have a 26th series, 327 & Ultramatic.

Transmission:
Mine is also very leaky and I top it up as necessary. The low band operates independent like the reverse band, so it not working is probably not affecting high. Have you tried adjusting your low band? It's is rather simple and that may be all it needs.

Are you running Type F transmission oil? The Ultramatics, unless they've been rebuilt do not like modern ATF.

I would think you would be able to tell if it was your transmission slipping as it should do it under load, such as pulling a hill or giving it more throttle.

You could try adding some Lucas Transmission fix to see if it made any difference, but what you're describing doesn't sound like a transmission issue to me, but maybe.

Bucking:
I would be more inclined to think carburetor issues would be more prominent when the engine was cold, rather than when warm and cruising down the highway.

I recently had a similar issue, which occurred when warm, and was erratic. It ended up being a bad coil, which wasn't even a year old. Engine was fine when it was cold and started acting strange when it warmed up. The coil had leaked it's oil, which I discovered because my plug wires were oily under my coil. Replaced the coil and it's been good ever since.

Those are my only thoughts at the moment....

Posted on: 7/28 15:50
 Top  Print   
 


Re: Bucking Slightly at Cruising Speeds
#3
Home away from home
Home away from home

Pgh Ultramatic
See User information
Are you sure the bucking is from the engine? It could be the feeling of the DD clutch engagement, if your throttle pressure is set far too high. Sometime drive the car accelerating at low throttle and see when it engages. Pay attention to the engine tone and try to feel a bit of a "thump" as the engine and drivetrain rev-match. If this occurs much above 30 mph then you will want to adjust the throttle pressure. Simply move the respective linkage about an ⅛" at a time towards the carb until it feels right when driving.

Torque tighten the low range brake band to specifications (per the manual) then re-test. If that doesn't cure it, or you are slipping in Low, just forget about it unless you want to drop the trans. But if you're leaking fluid, this should be on your to do list.

Keep in mind that the transmissions are the #1 neglected item on these cars due to difficulty in finding parts and service pre-Internet. But once in good shape and kept in adjustment, they should last probably 2 decades or 100,000 miles between major service.

Posted on: 7/28 17:52
1955 400 | Registry | Project Blog
1955 Clipper Deluxe | Registry | Project Blog
1955 Clipper Super Panama | Registry
Email (Parts/service inquiries only, please. Post all questions on the forum.)
service@ultramatic.info
 Top  Print   
 


Re: Bucking Slightly at Cruising Speeds
#4
Home away from home
Home away from home

53 Cavalier
See User information
Humanpotatohybrid makes a good point. The service manual, along with this thread, talks about adjusting the throttle linkage and the transmission throttle valve.packardinfo.com/xoops/html/modules/newbb/viewtopic.php?topic_id=28363

My throttle linkage and throttle valve were all whackadoodle, but I adjusted everything back to spec and the direct drive engages just like it's supposed to. It was engaging too soon before.

Having said that, at the speeds your talking about, I would think the governor would be overriding the throttle valve and keeping the direct drive fully engaged, which it should be doing when you let off on the throttle so it's using the engine for braking.

The more I get things back to spec on my car the better EVERYTHING works.

Posted on: 7/28 18:13
 Top  Print   
 


Re: Bucking Slightly at Cruising Speeds
#5
Home away from home
Home away from home

Pgh Ultramatic
See User information
Correct, a governor sticking at the "low speed" position (inward) could also cause this condition, but it's statistically less likely than someone monkeying with the linkage. And an order of magnitude more of a pain to fix.

Posted on: 7/28 18:17
1955 400 | Registry | Project Blog
1955 Clipper Deluxe | Registry | Project Blog
1955 Clipper Super Panama | Registry
Email (Parts/service inquiries only, please. Post all questions on the forum.)
service@ultramatic.info
 Top  Print   
 


Re: Bucking Slightly at Cruising Speeds
#6
Home away from home
Home away from home

53 Cavalier
See User information
Agreed, linkage first. But I found the arm on my throttle valve was not in the correct position either, which may have been adjusted to compensate for linkage that was out of adjustment. It's an easy adjustment.

Posted on: 7/28 18:25
 Top  Print   
Like (1)
 


Re: Bucking Slightly at Cruising Speeds
#7
Home away from home
Home away from home

Pgh Ultramatic
See User information
Yes, Packard specified that the lever adjustment should be within ±1/32, to keep the lever and the throttle valve link "in phase". Having them significantly out of whack will cause odd effects from the resultant non-linearity: the throttle pressure will be lower or higher than would be expected based on pedal position.

Posted on: 7/28 20:03
1955 400 | Registry | Project Blog
1955 Clipper Deluxe | Registry | Project Blog
1955 Clipper Super Panama | Registry
Email (Parts/service inquiries only, please. Post all questions on the forum.)
service@ultramatic.info
 Top  Print   
Like (1)
 


Re: Bucking Slightly at Cruising Speeds
#8
Home away from home
Home away from home

Joe
See User information
Digging in as we speak. I did check my points earlier today, found them to somewhat burned, so there's probably something there. I thought I had a new set, but no dice. Cleaned what I have for now. The coil (Echlin IC-7) tested good. about 1.2 Ohms on the primary winding, 9.84k on the secondary. No indication of leaking.

Checking the linkages - is there a workaround for the throttle cross shaft to carburetor adjustment. The manual only refer to a gauge, PU-312. Meanwhile, I've checked transmission throttle valve link; confirmed 5/32" short of lining up with the pin hole. (Related to this, troubleshooting section does also talk about the Low range and behaving like it's in neutral. The throttle valve link needs to be disconnected to try to free the "timing valve." Will try that later.) I've tried reset the Low range band (torque tighten to 20 ft. lbs., back off 1-3/4 turns), hasn't yielded a change there.

Going to recheck all my carb adjustments, too. Thank you all! I'll let you know if there any changes!

Posted on: 7/28 22:12
Joe B.
Greenville, NC
1950 Super Deluxe Eight Touring Sedan, Model 2302-5
327 w/ Ultramatic, 6v+
 Top  Print   
 


Re: Bucking Slightly at Cruising Speeds
#9
Home away from home
Home away from home

Joe
See User information
Well, it's 2:30 a.m. need to call it a night. I've never really had to fight spark, but that stopped me from getting anything checked. I lost spark, cleaned the points and got it back, checked my stuff on the carb, and lost spark again. I got it back, but it's very weak. I tried three different coils, the Echlin IC-7, a Pertronix Flamethrower, and Amazon special... all yielded the same very weak spark. Verified my battery to block ground was clean.

Guess it might just be time for some new points and a condenser.

Posted on: 7/29 1:48
Joe B.
Greenville, NC
1950 Super Deluxe Eight Touring Sedan, Model 2302-5
327 w/ Ultramatic, 6v+
 Top  Print   
 


Re: Bucking Slightly at Cruising Speeds
#10
Home away from home
Home away from home

Pgh Ultramatic
See User information
Quote:

Joe wrote:
Checking the linkages - is there a workaround for the throttle cross shaft to carburetor adjustment. The manual only refer to a gauge, PU-312.


Yes, the instructions I gave earlier to simply move it ⅛" towards the carb then road test, repeat/fine-tune as necessary.

Posted on: 7/29 5:13
1955 400 | Registry | Project Blog
1955 Clipper Deluxe | Registry | Project Blog
1955 Clipper Super Panama | Registry
Email (Parts/service inquiries only, please. Post all questions on the forum.)
service@ultramatic.info
 Top  Print   
 




(1) 2 3 »





- The following Google Ad-Sense Advert helps fund the cost of providing this free resource -
- Logged in users will not see these. Please Join and Donate to help support the website -
Search
Recent Photos
Photo of the Day
Recent Registry
Upcoming Events
Website Comments or Questions?? Click Here Copyright 2006-2024, PackardInfo.com All Rights Reserved