Merry Christmas and welcome to Packard Motor Car Information! If you're new here, please register for a free account.  
Login
Username:

Password:

Remember me



Lost Password?

Register now!
FAQ's
Main Menu
Recent Forum Topics
Who is Online
86 user(s) are online (80 user(s) are browsing Forums)

Members: 2
Guests: 84

Ross, BigKev, more...
Helping out...
PackardInfo is a free resource for Packard Owners that is completely supported by user donations. If you can help out, that would be great!

Donate via PayPal
Video Content
Visit PackardInfo.com YouTube Playlist

Donate via PayPal



(1) 2 »

Ignition distributor questions.
#1
Not too shy to talk
Not too shy to talk

Two-bit
See User information
Vehicle spec: 1951, 300 sedan, 327, ultramatic.

Left the house this morning, all good, almost to work (5-6 minutes run time) and loss of power, big time loss of power. Could barely keep it running. Random (pops) missfires in the exhaust. Could not get above 15 mph. Barely made it into a parking spot at work.
Had a few minutes, checked fuel, got fuel. Accelerator pump is squirting in the carb.
FFWD to end of work day.
Engine rolls over, no fire. Check hat and spinner, look ok. Points, not so good.
Catch a ride home from wife. Start looking for parts, ie: points and condenser.
How many dizzys did Packard use ??? I have seen listings for Delco, Presto-lite, and Auto-lite.

Getting back to the car tomorrow to see if i can find a tag on the dizzy. And bring some more tools to test for spark.
Standard Blue Streak was my go to for years for point ignitions.
Anything better for a Packard ? (once i figure out which dizzy i have.)
Thanks

Posted on: 10/1 19:48
 Top  Print   
 


Re: Ignition distributor questions.
#2
Home away from home
Home away from home

Packard Don
See User information
They used either Autolite or Delco-Remy but Prestolite and others offered aftermarket replacements. I think even Autolite offered Delco-Remy replacements and vice versa but I’m not sire! Point is (pun intended), you need to know which distributor you have before you can find the points for it and be sure to take a photo inside your distributor too just in case. Stores like Napa can often look up Packard but the points aren’t necessarily correct so a photo really helps.

Posted on: 10/1 19:53
 Top  Print   
Like (1)
 


Re: Ignition distributor questions.
#3
Home away from home
Home away from home

TxGoat
See User information
Better check coil and condenser, and ignition primary wiring.

If the engine sounds abnormal when cranking with the ignition off, you may have a timing chain issue.

Points rarely fail suddenly, but the condenser might.

Posted on: 10/1 20:57
 Top  Print   
Like (1)
 


Re: Ignition distributor questions.
#4
Not too shy to talk
Not too shy to talk

Two-bit
See User information
update: after todays testing i have a very ugly little yellow spark that cant even clear a 1/8 gap.
So, good news. Coil is trying, hat and spinner are co-operating, but i believe the condenser has left the chat.
New parts tomorrow.
Lets see how good i am with a feeler gauge, and a screwdriver.

Turns out its a Delco dizzy and my local parts house can have points and condenser by morning.
+1 for my locally owned parts store.

Posted on: 10/2 21:47
 Top  Print   
 


Re: Ignition distributor questions.
#5
Forum Ambassador
Forum Ambassador

HH56
See User information
6 volt electrical systems are unforgiving of issues a 12v system usually handles with ease so everything needs to be in pristine condition with good clean connections and decent size cables. Even if things work after changing the condenser a good idea would be to check the voltage at the coil terminal that is fed from the ign switch with the switch on and the car just sitting. Check again while the engine is cranking.

If the starter is pulling excess current or there is an ign switch issue, or a dirty or loose connection somewhere, or too small a battery cable or a marginal battery charge or CCA capacity the voltage at the coil terminal could be dropping so low the coil does not have enough power to produce a decent spark when trying to start. Just sitting the coil voltage should be at battery voltage of 6.3v or maybe a tenth or so below that. Anything less and I would start looking for connection problems. When cranking, if the coil supply voltage falls much below about 5.5 volts things start to get into iffy territory and any of the items listed could be causing the weak spark problem..

Posted on: 10/2 22:27
Howard
 Top  Print   
 


Re: Ignition distributor questions.
#6
Home away from home
Home away from home

su8overdrive
See User information
Bought a set of Blue Streak points for the '40 120 i then owned in the late '70s. My retired aero/auto mechanic/machinist pilot took one look at them, exclaiming, "They're plastic. Take these back and get a set of Echlin." He was right. They were partially plastic. I've used Echlin ever since.

HH56 and the others give good advice. There's a nifty search bar to the above right of the home page for obvious, covered to death topics. But again, make sure you've got double aught (00) solid copper battery cables, ends both crimped and soldered. "Heavy duty" cables from the local car parts store in this 12-volt world still too skimpy. If you have a battery disconnect switch--which you should--make sure it's rated for more amps than your starter draws. Cole Hersee brass marine grade from any NAPA or online a good choice.

boatplicity.com/9029458-cole-hersee-m284 ... rm=2331583126725667&utm_content=AG1'

Once you get sorted -- and always follow the Packard shop manual -- make sure to clean out the distributor grease cup and refill with good black molybdenum-graphite grease and give it a turn every 1,000 miles. A worn distributor shaft will upset your timing.

Posted on: 10/2 23:39
 Top  Print   
 


Re: Ignition distributor questions.
#7
Not too shy to talk
Not too shy to talk

Two-bit
See User information
New points and condenser installed.
Popped right off second roll of the starter.
Out of the parking lot a work, now home.
Break out the tach/dwell meter this wknd and "fine tune."

Thanks for the help.

Posted on: 10/4 6:00
 Top  Print   
Like (1)
 


Re: Ignition distributor questions.
#8
Home away from home
Home away from home

53 Cavalier
See User information
Quote:

Two-bit wrote:
New points and condenser installed.
Popped right off second roll of the starter.
Out of the parking lot a work, now home.
Break out the tach/dwell meter this wknd and "fine tune."

Thanks for the help.


Good news!!!

When setting the points using a dwell meter, what is the correct setting for a 327 with a Delco-Remy distributor? 30 degrees?

Posted on: 10/4 20:13
 Top  Print   
 


Re: Ignition distributor questions.
#9
Not too shy to talk
Not too shy to talk

Two-bit
See User information
According to the "tune-up" specs you can run 21* to 30*. With a range like that i shot for the middle and got 25*>26*. Called it good.
I think it called for .016 gap, i ended up with .018.
I have always considered the advertised gap a starting point, then adj for your dwell reading.

Posted on: 10/4 20:34
 Top  Print   
 


Re: Ignition distributor questions.
#10
Home away from home
Home away from home

53 Cavalier
See User information
Thanks, I could only find the gap setting in the service manual, not the dwell setting.

Posted on: 10/4 20:51
 Top  Print   
 




(1) 2 »





- The following Google Ad-Sense Advert helps fund the cost of providing this free resource -
- Logged in users will not see these. Please Join and Donate to help support the website -
Search
Recent Photos
Photo of the Day
Recent Registry
Upcoming Events
Website Comments or Questions?? Click Here Copyright 2006-2024, PackardInfo.com All Rights Reserved