Happy Easter and welcome to Packard Motor Car Information! If you're new here, please register for a free account.  
Login
Username:

Password:

Remember me



Lost Password?

Register now!
FAQ's
Main Menu
Recent Forum Topics
Who is Online
111 user(s) are online (74 user(s) are browsing Forums)

Members: 1
Guests: 110

BigKev, more...
Helping out...
PackardInfo is a free resource for Packard Owners that is completely supported by user donations. If you can help out, that would be great!

Donate via PayPal
Video Content
Visit PackardInfo.com YouTube Playlist

Donate via PayPal



« 1 ... 3 4 5 (6)

Re: Electronic Ignition conversion report
#51
Just can't stay away
Just can't stay away

Moms 54
See User information
Ok Thank you,
I just made new 1/0 cables, I did crank her with no problems thus far!

Is there a proper way to test that logic for the supplied volts..

Thank you OD on the plugs.

Posted on: 2016/10/29 13:35
The best are yet to roll
 Top  Print 
 


Re: Electronic Ignition conversion report
#52
Forum Ambassador
Forum Ambassador

Owen_Dyneto
See User information
You might consider checking the primary voltage at the coil while the starter motor is engaged. Pull the high tension wire from the center of the distributor to prevent the engine from starting while you take the measurement.

Posted on: 2016/10/29 13:44
 Top  Print 
 


Re: Electronic Ignition conversion report
#53
Just can't stay away
Just can't stay away

Moms 54
See User information
Ok Thank you

I'm going into town tomorrow for plugs and wires, so I'll take that reading soon after that trip.

Fingers crossed on the pertronix, a buck n half out the window would really not feel good!

I had also bought their Flame Thrower coil.
If the solid state is a no go I should still be able to use the coil, I don't see any reason not too..

Posted on: 2016/10/29 23:32
The best are yet to roll
 Top  Print 
 


Re: Electronic Ignition conversion report
#54
Just can't stay away
Just can't stay away

Moms 54
See User information
Any preference gap on them 308 plugs?

Posted on: 2016/10/30 23:45
The best are yet to roll
 Top  Print 
 


Re: Electronic Ignition conversion report
#55
Home away from home
Home away from home

Ross
See User information
.025 is the factory spec. If you get your Pertronix to work you could try .030 but it will make very little difference at the compression ratio and speeds we are talking about in a 54.

Posted on: 2016/10/31 5:33
 Top  Print 
 


Re: Electronic Ignition conversion report
#56
Just can't stay away
Just can't stay away

Moms 54
See User information
Yes in a 54'.

Posted on: 2016/10/31 11:58
The best are yet to roll
 Top  Print 
 


Re: Electronic Ignition conversion report
#57
Quite a regular
Quite a regular

2150
See User information
I have been corresponding lately withhttp://www.c5ignitions.com/c5-technology.html regarding ignition for my Mercedes 1973 SLC.
I have not ordered anything yet as the owner/producer of the system is not at home right now but he seems to be a helpful and skilled person. At this time I have the impression that it is impossible to install and keep the standard look but in my opinion this system seems more modern compared to Pertronix.

I will probably buy a system for the SLC this winter.
That might give a possibility to see if it could be applied to a 356 Packard without disturbing the original appearance.

I have very mixed feelings regarding upgrading of old vehicles.
On one hand if a car was made in a certain way and is modernized the feeling of a historic piece might be lost. On the other hand I am very happy with modern rubber in my tires or modern oil and grease that limits the need for oilchange several times a year and frequent engine overhauls.

Posted on: 2016/11/1 5:01
 Top  Print 
 




« 1 ... 3 4 5 (6)




Search
Recent Photos
Photo of the Day
Recent Registry
Website Comments or Questions?? Click Here Copyright 2006-2024, PackardInfo.com All Rights Reserved