Hello and welcome to Packard Motor Car Information! If you're new here, please register for a free account.  
Login
Username:

Password:

Remember me



Lost Password?

Register now!
FAQ's
Main Menu
Recent Forum Topics
Who is Online
95 user(s) are online (51 user(s) are browsing Forums)

Members: 1
Guests: 94

Don Shields, more...
Helping out...
PackardInfo is a free resource for Packard Owners that is completely supported by user donations. If you can help out, that would be great!

Donate via PayPal
Video Content
Visit PackardInfo.com YouTube Playlist

Donate via PayPal




Differential Gear Thrust Washers
#1
Home away from home
Home away from home

Joe
See User information
Hey all. Working on a 23rd series, Ultramatic, 3.54 rear end. Pulled rhe carrier to replace the gasket, copper wire rings, and clean everything up. Upon inspecting the internals, I found one of the differential gear thrust washers isn't seated properly between the bearing and gear, and on the other side, there's no thrust washer at all. Pinion thrust washers are both in tact. Diff made no noise, and no metal in the fluid. Just seems unusual, and parts book shows each gear having a thrust washer. I do know there were varying thicknesses to the washers, too.

Want to get several opinions here... should I get this rebuilt, or would you run it? Or is it easy enough to to replace the thrust washers, and I could just do it myself? I would think I would just have to follow the manual procedure for up until I hit "Drive Pin Removal," which, theoretically, I wouldn't have to do to replace the thrust washers. Question of course would be washer thickness.

Thanks in advance your advice and experience.

Attach file:



jpg  20240417_212016.jpg (2,026.49 KB)
225648_66207b3e3669a.jpg 4000X3000 px

jpg  20240417_184706.jpg (2,819.77 KB)
225648_66207b66e9d69.jpg 4000X3000 px

Posted on: 4/17 20:48
Joe B.
Greenville, NC
1950 Super Deluxe Eight Touring Sedan, Model 2302-5
327 w/ Ultramatic, 6v+
 Top  Print   
 


Re: Differential Gear Thrust Washers
#2
Home away from home
Home away from home

Ross
See User information
In your top photo the thrust washers are on the smaller spider gears that run left-right in the photo. Up down in your photo are the side gears, the axle shafts protrude through these and touch against the thrust block. The axles should push against the block directly so I am perplexed by that shim (?) that seems adhered to the side of the thrust block. It should pull right out as the thrust block has plain flat sides. The thrust block should have quite a bit up up-down play in your photo.

The absence of chips or noise tells me the diff is fine. When you reassemble, you will need to pay particular attention to your axle end play as I am guessing that piece of metal was somebody's fix for not understanding how to regulate the play with the shims out at the wheel bearings.

Posted on: 4/18 6:16
 Top  Print   
Like (1)
 


Re: Differential Gear Thrust Washers
#3
Home away from home
Home away from home

Guscha
See User information
"...The absence of chips or noise tells me the diff is fine..."

... or vibrations.

Posted on: 4/18 16:56
The story of ZIS-110, ZIS-115, ZIL-111 & Chaika GAZ-13 on www.guscha.de
 Top  Print   
 


Re: Differential Gear Thrust Washers
#4
Home away from home
Home away from home

Joe
See User information
Awesome. Thanks, guys. Can confirm, nothing seemed particularly unusual from the rear end prior to disassembly. Was smooth and quiet.

In checking for end play, what is the best way to do this absent the gauge mention in the manual?

Posted on: 4/18 17:19
Joe B.
Greenville, NC
1950 Super Deluxe Eight Touring Sedan, Model 2302-5
327 w/ Ultramatic, 6v+
 Top  Print   
 


Re: Differential Gear Thrust Washers
#5
Home away from home
Home away from home

Ross
See User information
I like to use a dial indicator with a magnetic base. I stick the base to the axle and let the probe push against the backing plate. Push the axle in, then pull it outwards and read the difference. Or push the axle in and then clamp some bent up piece of steel to the axle with a vice grip or clamp. Clamp the steel so it is just touching the backing plate, then pull the axle outwards and measure the gap with feeler gages.

Posted on: 4/18 20:22
 Top  Print   
 


Re: Differential Gear Thrust Washers
#6
Home away from home
Home away from home

53 Cavalier
See User information
If it's not broke don't fix it.................but sometimes if things are not correct they should be corrected. I would be inclined to correct this as it seems that with the correct parts/tools this would be a rather simple project, and it would put my mind at ease. Actually what I would really do is whatever Ross says to do!

Posted on: 4/18 21:56
 Top  Print   
 


Re: Differential Gear Thrust Washers
#7
Home away from home
Home away from home

Joe
See User information
Well, curiosity got the better of me. I had planned to run it as is and working to just get the end play right, but the new gasket leaked after the third day of having fluid in it (gasket tore, sigh), so, knowing I had to do the gasket again, I took it down and decided to tear into it a little further. Here's what I found with that thrust washer I pulled out vs. a new-old one. Not sure what I pulled out of there was even for a Packard diff, unless it had just pancaked that badly.

So, we'll get those back in spec and do the other checks per the manual and get it re-hung.

Attach file:



jpg  20240425_091926.jpg (2,898.06 KB)
225648_662a5c5c2bc74.jpg 4000X3000 px

Posted on: 4/25 8:42
Joe B.
Greenville, NC
1950 Super Deluxe Eight Touring Sedan, Model 2302-5
327 w/ Ultramatic, 6v+
 Top  Print   
Wow (1)
 


Re: Differential Gear Thrust Washers
#8
Home away from home
Home away from home

53 Cavalier
See User information
Sometimes it's hard to know how far down the rabbit hole a person should go, but in this case it was good to go a little further. That's a good fix!

Posted on: 4/25 9:41
 Top  Print   
Like (1)
 








Search
Recent Photos
Photo of the Day
Recent Registry
Website Comments or Questions?? Click Here Copyright 2006-2024, PackardInfo.com All Rights Reserved