1933-36 (10th->14th Series) - ENGINE
|
Subject | Application | Document |
Break-In Period refrain from full power operation - limit speed | (all models) | |
Compressometer Adapter new special tool - compression testing, no. 6 cylinder | 905-6 1005-6 1107-8 | |
Connecting Rod (Tenth Series, The) new model information - heavier bearing end/bolts | 1001-2 | |
Connecting Rod Bearings undersize - markings, identification | 12th 120 | |
Connecting Rod Bleed Holes reduced, relocated to trailing side installation in earlier cars | 9th-10th | |
Connecting Rod Holder new special tool, piston pin installation - fabricate, blueprints available | (not specified) | |
Connecting Rod, Replacement of crank pins out of round - returning tool, undersize rods | (not specified) | |
Connecting Rods fitting bearings - thin babbit, reiterated | 10th | |
Connecting Rods fitting bearings - thin babbit | 10th | |
Connecting Rods, Motor - 1929 to 1936 Inclusive stocking simplification - rod and bearing part reference | 7th-14th | |
Crank Pins, Trueing babbit wiped out - burnishing required | (not specified) | |
Cylinder (Block) Exchange reground, factory exchange service - illustrated refinishing process | (not specified) | |
Cylinder and Piston Assemblies Available short block less crankshaft - back in stock | 1203-4-5 1403-4-5 120-138CD 115C 1600-1-1A-1D-2 1700-1-1A-2 18th-21st | |
Cylinder Block Water Passages valve seat, additional cooling - drilling clarification | (not specified) | |
Cylinder Chamfering Tool new special tool - purchase or fabricate, blueprints available | (not specified) | |
Cylinder Drain Cup new special tool - block grinding/cleaning | 1107-8 | |
Cylinder Head Corrosion aluminum - checks, maintenance, precautions | 12th-14th 120-138CD 115C 15th-16th 1707-8 | |
Cylinder Head Gasket aluminum head corrosion - copper ferrules now steel | 12th | |
Cylinder Head Gasket Seal precoated - part reference | 7th-14th 120-138CD 115C 15th-16th 1700-1-2-3-5 | |
Cylinder Head Gaskets overheating - water passage blocked by sealing film | (not specified) | |
Cylinder Head Nut Wrench new special tool - between coils | 10th | |
Cylinder Head Nuts, Tighten head failures/leaks, oil consumption - proper replacement, torque-tightening | (all models) | |
Cylinder Head Nuts, Tightening oil consumption, poor economy/performance, cracked heads - tensioning wrench, procedure | (all models) | |
Cylinder Head Studs oversize threads, water jacket seal - identification, sealing paste | All Models | |
Cylinder Head Tension Wrench proper tightening reiterated - alternate special tools | (all models) | |
Cylinder Heads new cast-iron, supersedes aluminum - redrilling not required | 1200-1-2 1400-1-2 1500-1-2 1603-4-5 | |
Cylinder Repairs sand hole, shrinkage cracks - Wonder Weld | (all models) | |
Cylinder Repairs small holes/cracks - repair compounds | (all models) | |
Cylinder Wear unusual wear - air cleaner neglect | (not specified) | |
Cylinders and Valves, Rusted moving stored vehicles - preparations for starting | (all models) | |
Flywheel Assembly, Motor - Parts Book Correction application error | 1401-2-3-4-5 | |
Manifold Gasket Failures chafing - chamfer manifold edges | (all models) | |
Manifold Nut Wrench, Exhaust new special tool - T-handle type, multiple uses | (not specified) | |
Motor Holder new special tool - transmission removal, adapter and jack | 10th | |
Motor Support new special tool - transmission removal | 10th-11th | |
Motors, Eleventh Series longer life - improved lubrication, bearings | 11th | |
Oil Control - Eight and Super Eight piston rings - alternate combinations | 1201-2-3-4-5 1401-2-3-4-5 | |
Oil Cooler Installation - Twelve mounting/tightening procedure | 905-6? 1005-6? 1106-7-8? 1207-8 | |
Oil Cooler Replacement cooler and gauge tube assembly, labor allowance - Eight, Super Eight | (not specified) | |
Oil Cooler Replacement expedite processing - limited stock | 1100-1-2-3-4-5 | |
Oil Filters, Fitting new style fitting - rework supporting bracket | 11th | |
Oil For Sub-Zero Operation, Winter Engine new 5-W oil - issues, limited availability/use | (all models) | STB 49T-40 (Zones only) |
Oil Pan Drain Plug, Motor new hex-head service plug - spark plug wrench | 901-2-3-4 1001-2-3-4 1100-1-2-3-4-5 1200-1-2-3-4-5 | |
Oil Pump - Twelve noisy valves - metering valve sticking | 905-6? 1005-6? 1106-7-8? 1207-8 | |
Oil Pump - Twelve noisy valvetrain at start-up - metering valve sticking | ?1005-6 ?1106-7-8 ?1207-8 ?1406-7-8 ?1506-7-8 ?1607-8 1707-8 | |
Oil Pump Body Cover - Now Available had been difficult to procure | ?1100-1-2-3-4-5 1200-1-2-3-4-5 1400-1-2-3-4-5 1500-1-2 1603-4-5 1703-3A-5 | |
Oil Pump Pressure Relief Valve Nut Wrench Special new special tool - adjusting oil pressure | 905 1005 11th | |
Oil Pump Shaft Lubrication shaft twisting off - lubrication during storage | (all models) | |
Oil Recommendation, New Motor hard/no starting - additional weights, table | (all models) | |
Oil Test Connection new special tool - pressure test tank extension | 905-6 1005-6 | |
Oils, Graphited no cost/benefit advantage | (all models) | |
Perfect Seal - Gasket Paste non-hardening sealant - head gaskets, additional applications | (all models) | |
Perfect Seal Gasket Paste additional size - applicator kit required | (all models) | |
Piston and Rings, Replacement latest type used for earlier models - check replacement chart for rings only | 9th-14th 120-138CD 115C 15th-20th | |
Piston Oversize Diameters revised specification, skirt clearance reduced - size reference | ?1st-14th 120-138CD 115C 15th-16th | |
Piston Oversize Diameters revised specification, variation reduced - size reference | ?1st-14th 120-138CD 115C 15th-17th | |
Piston Ring Combination - Eight and Super Eight previous oil control combination suggestion - now in production | 1201-2-3-4-5 1401-2-3-4-5 | |
Piston Rings, Carbonized oil consumption, low speed, cold weather - oil changes, cleaning procedure | (all models) | |
Piston Rings, Selling and Installing Perfect Circle ring groove combinations - use of selection chart | 9th-14th 120-138CD 115C 15th-20th | |
Piston Slap tight pins, shrunken pistons - cold weather, normal condition | (all models) | |
Piston, Pin and Ring Oversize Marking, Motor identification - size/color reference | (all models) | |
Pistons skirt slot position - now installed facing valves | 1st-8th 9th-11th | |
Pistons, Fitting aluminum - procedure | (all models) | |
Power, L-Head vs. Valve-In-Head higher torque/HP - detonation | (all models) | |
Rocker Lever Housing Piston Releaser new special tool - purchase or fabricate, blueprint available | 1005-6 | |
Scientific Equipment and Data in Diagnosing Service Complaints, Use of over-all motor check-up - starting/charging, carburetion | (all models) | |
Sludge, Crankcase reduced driving, condensation, bearing trouble - operating temperatures, oil changes | (all models) | |
Sludge, Engine cleaning oil pan/screen - engine flushing | (all models) | |
Starting Instructions glove compartment door sticker - lubrication record | 10th | |
Stud Remover and Driver new special tool - cylinder head studs | (all models) | |
Valve Depth Gauge new special tool - valve stem clearance | 905-6 1005-6 | |
Valve Spring Compressor new special tool - tension reading | (all models) | |
Valve Spring on Packard Twelve incorrect field installation - proper orientation, dimension | 905-6? 1005-6? 1106-7-8 | |
Valve Springs broken - water leakage, corrosion | (all models) | |
Valve Stem Length Indicator Gauge new special tool - purchase or fabricate, blueprint available | 1005-6 | |
Valve Tappet Adjustment camshaft revised - exhaust valve tappet clearance increased | 1001-2-3-4 | |
Valve Tappet Adjustment camshaft revised - exhaust valve tappet clearance increased | 1001-2-3-4 | |
Valve Timing specifications reference | 900-1-2-3-4 10th-14th (exc. Twelves) 120-138CD 115C 15th-19th 2000-1-3-3A-4-5-6-7-8-20-21-23 | |
Valve Wrench - Tool Suggestion improvement - stops slipping | (not specified) | |
Valves and Car Storage, Sticky running motors, internal rust - cylinder oiling, battery removal/charging | (all models) | |
Valves, Rusted Cylinders and moving stored vehicles - preparations for starting | (all models) | |
Valves, Sticking vehicles in storage - precautions reiterated | (all models) | |
Valves, Sticky cold starts/stops, rust in guides - new corrosion-resistant material | (all models) | |
Vibration Damper Wrench and Puller special tool - sale pricing, description | (not specified) | |
Warm Weather Service engine/cooling system - inspection/maintenance | (all models) | |
Water Chamber Cover Plates, New Type improved water circulation - cooler valve seats | ?7th-11th | |
Winter Lubricants hard starting - lighter motor oil | (all models) |
SC = Service Counselor | SL = Service Letter | STB = Service Technical Bulletin | SSB = Studebaker Service Bulletin |
NOTE: These PDFs were created from High Quality Scans. It is recommended that you Right Click on the link(s) above and do a "Save Target As". This will download the PDF to your machine rather than trying to open and view it over the web.
Disclosures & Disclaimers
Though previously published elsewhere, this work is provided with my full permission for display on the PackardInfo.com website and the personal use of visitors to that site. Any other unauthorized use, however, is expressly prohibited and may be subject to prosecution.
Also, because this index was compiled from documents published by the factory, neither the author nor PackardInfo.com are responsible for errors in content arising from source information.