1937-42 (15th->20th Series) - ALL ITEMS
|
| Subject | Application | Document |
327 Engine Installation Kits Installation Instructions | 1703-1703A-1705 | |
AC Spark Plugs Information on Blue Top Plugs | (not specified) | |
Accelerator Sticks in Open Position (Electromatic) linkage catches on clutch cable pulley - spring out of place | 19th-20th | |
Adjustment, Transmission direct/second shift fork travel - finger/boss clearance | 1700-1-2-3-5 | |
Aero-Drive Indicator Light always on - headlamp resistance unit bent. grounded | 19th | |
Aero-Drive Indicator Light on, standing - fuse check | 19th-20th | |
Air Cleaner Cover Pads, Loose poor mileage - restricted air passage | (not specified) | |
Air Cleaner Oiling Instructions, AC SAE 50 discontinued - alternate products | (not specified) | |
Air Cleaner, Oil-Bath - Effect of...on Economy new natural fiber, restricted from pack-down - proper cleaning | (not specified) | |
Air Cleaners - Effect on Fuel Economy clogging - proper cleaning | (not specified) | |
Air Cleaners excess oil, leaks - distributor wires shorted | 1803-3A-4-5-6-7-8 | |
Air Cleaners, Oil Bath oil-fouled spark plugs - overfilled cleaner | (not specified) | |
Air Cleaners, Oil Bath seasonal oil selection | (not specified) | |
Antenna - New Accessories longer - improved radio reception | (not specified) | |
Antenna Knob, Stripped - Accessory Notes damaged serrations - service part, proper installation | 19th | |
Antenna, Cowl with Spotlight revised top hole cowl location | 16th | |
Antenna, Rotary - Accessory Notes antenna rod shaft grounded - new shaft insulating bushing | (not specified) | |
Anti-Freeze - Types Information about the different types | (Not Specified) | |
Anti-Freeze production mix - future shortages, alternate product | 20th | |
Anti-Freeze Restriction | (all models) | |
Anti-Freeze Solution acceptable types/brands - characteristics | (all models) | |
Anti-Freeze Solution, Care of expected shortage - rust inhibitor | (all models) | |
Anti-Freeze Solution, Injurious limitation order - damaging products | (all models) | |
Anti-Freeze Solutions re-use of saved ethylene glycol permitted - strengthening, reinhibitor | (all models) | |
Anti-Freeze Solutions, Care wartime shortage - use, testing, renewing, storing | (all models) | |
Anti-Freeze Solutions, Care of future availability, saving - follow supplier recommendation | (all models) | |
Anti-Freeze Tester, New Type for new Prestone type - specific gravity changed | (all models) | |
Anti-Freeze, Alcohol as an ethylene glycol replacement - thermostat, leaks, non-pressure cap for 19th-20th | (all models) | |
Anti-Freeze, Draining future availability, discarding - rust inhibitor additive for water | (all models) | |
Anti-Freeze Factory Delivery Cars | (Not Specified) | |
Antifreeze in Factory Car Shipments Prestone shortage, shipped with alcohol - high reading thermostats, heater equipment | 120C; 115C; 15th | |
Armite Anti-Seize Compound utility item | (all models) | |
Axle End Play, Rear thrust block, measuring/adjusting - shim reference | 1600-1-2 | |
Axle Shaft End Play Fixture, Rear new special tools - required | 1600-1 | |
Axle Shaft Inner Oil Seal, Rear improved, spring type - part number reference | 120-138CD; 115C; 1600-1-1A-1D-2; 1700-1-1A-2-3-3A-5; 18th-20th | |
Axle Shaft Lubricator Sleeve, Rear new special tools - required | 1600-1 | |
Axle Shaft Oil Leaks, Rear causes - checks/corrections | (not specified) | |
Axle Shaft, Rear - Special Tools new required tools - nut wrench, puller/adapter | 1800 | |
Backing Light product information - automatic operation | 18th? | |
Backing Light product information - automatic | 19th? | |
Backing Light Bracket fender guards - higher bracket available | 1900-1 | |
Backing Light, Automatic product information - benefits | 20th | |
Backing Plates, Brake brake noise, oil leaks - loose, checks | (all models) | |
Batrometer Overview and Use | (not specified) | |
Batteries in New Case unused, loss of charge - check fluid level, specific gravity | (not specified) | |
Batteries, Help Owners Conserve inspection - maintenance /repair | (all models) | |
Batteries, Run-Down cold weather, reduced driving - smaller generator pulley, exc. Super Eight | (all models) | |
Batteries, Selling immediate need only - inspection, electrical system check-up | (all models) | |
Battery Charging, High-Speed disadvantages - not recommended | (all models) | |
Battery Ground Cables substandard replacements - OE quality, features | (all models) | |
Battery Life Information | (Not Specified) | |
Battery Solution, Loss of overcharging - defective regulator | (all models) | |
Battery Tester - Stop and Go new special tool - in-car testing | (all models) | |
Battery, Keeping Charged smaller generator pulley reiterated - Delco alignment | (not specified) | |
Battery, Storage lead shortage - testing, charging | (all models) | |
Bearing Clearance, Main and Rod noise, vibrations - identification, measurement | (not specified) | |
Bearing Replacements, Connecting Rod unnecessary replacement - limitation order, guidelines | (not specified) | |
Bearing Sets, Main now available - cost-savings | 120-138CD; 115C; 1600-1-2; 1700-1-2 | |
Bearing Shells, Connecting Rod new larger bearings/rods - machine older rods to fit | 120-138CD; 115C; 1600-1; 1700-1-1A | |
Bearing Shells, Main and Connecting Rod - Lead Base Babbitt wartime shortage, tin discontinued - characteristic appearance | 20th | |
Bearing Shells, Note on rod/main bright or dull - no effect | (not specified) | |
Bearings Measured Quickly, Rod and Main new Plastigage Kit - proper use | (not specified) | |
Bearings, Care of Ball and Roller installation/removal damage - proper support | (all models) | |
Bearings, Connecting Rod - Service Letter Correction new larger bearings/rods - not interchangeable, identification | 1700-1-1A | |
Bearings, Connecting Rod new larger bearings/rods - not interchangeable, identification | 1700-1-1A | |
Bearings, Connecting Rod rod no longer supplied, use 17th Series - identification, precautions | 120C-138CD; 115C; 1600-1-1A | |
Bearings, Connecting Rod Super Eight production change - less running clearance | 1603-4-5 | |
Bearings, Crankshaft .020 - Parts Men Note after grinding - parts reference | 1703-3A-5 | |
Bearings, Rough Transmission Driving Shaft 1st/2nd gear service assemblies - lubricate prior to install | 17th-54th | |
Bearings, Undersize Crankshaft material shortage - crankshaft regrinding | (not specified) | |
Bleeder Tool Change new check-valve type, set of four - one-man operation | 120-138CD; 115C; 15th-17th; (18th-21st) | |
Bodies (Replacement) not available - field referral process | (all models) | |
Body Noise rear floor to gas tank strap pads - rear seat X-brace pad missing | 19th | |
Body Pillars, Center cracked at beltline - new, weld-in reinforcement available | 1600-1 | |
Body Rumble trunk floor, frame contact - fabric insulators, raising body | 1600-1-2 | |
Body Shop Supplies Information | (not specified) | |
Bonnet Emblem, PACKARD product information - hood side panel | (not specified) | |
Bonnet Holder tool suggestion - fabricate locally | 16th; (17th-18th) | |
Bonnet Louver Medallion backordered - supplier issue | 1800-1 | |
Bonnet Louver Medallion nosepiece, color worn through - improved parts | 1800-1 | |
Bonnet Top Center Hinge Molding - Now Available had been difficult to procure | 1901-1A-3-3A-4-5-6-7-8 | |
Bonnet Top Prop Assembly now available again | 1901-1A-3-3A-4-5-6-7-8 | |
Breaker Points dirty, burnt oil - plugging distributor hole | 1800 | |
Breaker Points excessive voltage, adjusting regulator - new condensor reiterated | 1800 | |
Breaker Points, Blued hard starting, cold - narrow gap, overcharging | (all models) | |
Bug Screens product information - radiator protection | 19th | |
Bumper Guards Exhaust Noise | (Not Specified) | |
Bumper Support Bars - Items Now Available back in stock - front, inner | 1800-1 | |
Bumper Support Bars - Items Now Available back in stock - front, outer | 18th | |
Bumper Support Bars - Items Now Available back in stock | ?2004-05-07-08-20-21-23-30-55? | |
Cable Connectors open circuit, poor contact - inspection/correction | (not specified) | |
Camber Adjustment specification changed - new offset adjusting pilot | 1900-1 | |
Camshaft and Valve Springs cast-iron/steel, engine suffix identification - corresponding oil pump gear | 1600-1-2 | |
Camshaft Valve Holder, Motor new special tools - required | 1600-1 | |
Camshaft, Carburetor and production profile change - new carburetor required | 1803-3A-4-5-6-7-8 | |
Cap, Locking Gas Tank product information - benefits | 19th | |
Capacity, Rear Axle fluid - changes | 120C-138CD; 115C; 1600-1-1A-1D-2; 1700-1-1A-2-3-5; 18th | |
Car Storage short-term - precautions | (all models) | |
Car Storage winter - precautions, conditions | (all models) | |
Car Storage, Further Notes on instructions superceded - wheel block fabrication | (all models) | |
Car Storage, Sticky Valves and running motors, internal rust - cylinder oiling, battery removal/charging | (all models) | |
Carbon Rattle piston carbon deposits striking head - use of additional head gasket | (not specified) | |
Carburetion - Super Eight/120 low speed stumble - drill out idle tubes, stretch accelerator pump spring | 1801; 1803-3A-4-5-6-7-8 | |
Carburetion stumble under light throttle - additional field modifications | 1803-3A-4-5-6-7-8 | |
Carburetor and Camshaft production profile change - new carburetor required | 1803-3A-4-5-6-7-8 | |
Carburetor: Chandler-Groves Pump Seal Puller new special tool - procedure | 1600; 1700 | |
Carburetor: Choke stalling, loading, flooding, cold weather operation - checks/adjustments, proper operation | (not specified) | |
Carburetor: Choke Adjustment excessive fuel consumption, unloader operation - plugged screen, stuck piston | 1901-1A; 1951; 20th; (21st-23rd) | |
Carburetor: Choke Screens, Cleaning poor performance, choke not open - clogged screen (WDO) | 1901-1A; 1951; 20th-23rd | |
Carburetor: Chokes, Sticking hard starting, loading up - gummed shaft, cleaning | (not specified) | |
Carburetor: Cleaning Caution use of compressed air - air horn removal required | (not specified) | |
Carburetor: Cold Stalling Due to Carburetor Icing explanation - prevention | (all models) | |
Carburetor: Cut-Out, High Speed fuel starvation, Chandler Groves - new design float needle/seat | 1600 | |
Carburetor: Dirt in fuel pump strainer disc separation - loose nuts | 18th | |
Carburetor: Economizer Valve Inspection Cover new special tool - Chandler-Grove carburetors | 115C, 1600 | |
Carburetor: Float Level Gauge new special tool - instructions | 1200; 1300; 1400; 120C; 115C; 1500 | |
Carburetor: Gasket Equipment sets now available - part reference | 905-6; 1001-2-3-4-5-6; 1100-1-2-3-4-5-6-7-8; 1200-1-2-3-4-5-7-8; 1400-1-2-3-4-5-7-8; 120-120C; 115C; 15th | |
Carburetor: Gasket Equipments complete gasket sets - now available | 905-6; 10th-14th; 120-120C; 115C; 15th | |
Carburetor: Gasket Sets now available | 17th | |
Carburetor: Gasket Sets, New - Stromberg | 1601-2 | |
Carburetor: Gasket Sets, New production change - early/late, identification | 1600 | |
Carburetor: Idling Adjustment idle quality - idle air bleeder enlarged - redrill in field | 1903-3A-4-5-6-7-8 | |
Carburetor: Miss, Pick-Up flat-spot/stumble, hot, Chandler Groves - new longer accelerator pump link | 1600 | |
Carburetor: Motor Miss insect debris entering float bowl vents, Chandler-Groves - fabricate/install baffle | 1600; (1700) | |
Carburetor: Overchoking loading during warm-up - adjustments reiterated, fast idle cam rod, new thermostats | 18th | |
Carburetor: Overchoking loading up. rolling - checks/adjustment, Super Eight choke piston modification, heat valve adjustment | 18th | |
Carburetor: Overchoking loading up. rolling - insufficient heat, choke valve sticking | 18th | |
Carburetor: Settings - Stromberg model reference | 120-138CD; 1601-2; 1701-2; 1801-1A; 1901-1A | |
Carburetor: Settings visual identification - reference chart | 905-6; 10th-14th; 120-120C; 115C; 15th | |
Carburetor: Special Tools new required tools - choke setting, float level gauges | 1803 | |
Carburetor: Tightening die-cast parts - air leaks | (all models) | |
Carburetor: Tools new tools - Stromberg | 1700-1-1A-2 | |
Cars in Storage indefinite - added precautions | (all models) | |
Caster Adjusting Shims tapers shims - holes revised to fit Super Eight | 120-120C; 115C; 1500-1-2 | |
Center Bearing Mounting drive line disturbance, long-wheelbase cars - rubber insulators, proper installation | 1601A-2; 1701A-2-3A-4-5-7-8; 1801A-3A-4-5-7; 1901A-3A-4-5-7; 2005-07-08-55 | |
Change Over, Right Hand Drive Information, Not Advised | (not specified) | |
Chatter, Clutch backing up - fore-to-aft stabilizer (snubber), Junior retrofit | 1600-1 | |
Chatter, Clutch backing up - stabilizer (snubber) reiterated, neutralizing mounts | 1600-1 | |
Chatter, Clutch low, reverse - motor supports, stabilizer (snubber), clutch plate condition | (all models) | |
Chatter, Clutch superseded snubber, 17th Series retrofit - rear spring Silenite inserts | 1600-1 | |
Chrome Plating cleaning - protective coating | (all models) | |
Chrome Plating wartime shortage - handling rust complaints | (all models) | |
Chrome Plating, Care of environmental factors, wartime shortage - cleaning/polishing | (all models) | |
Chrome Plating, Preservation of decorative plating suspended - use of lacquer | (all models) | |
Cigar Lighters, Automatic standard/accessory - instructions, troubleshooting | 120C; 115C; 15th | |
Cleaning Water Systems scale/rust, overheating - chemical cleaner, rust inhibitor | (all models) | |
Cleaning Water Systems scale/rust, overheating - chemical cleaner, rust inhibitor | (all models) | |
Cleaning Water Systems scale/rust, overheating, delayed cleaning - chemical cleaner | (all models) | |
Clock - Detail Parts not available - return to vendor for service | (not specified) | |
Clock Installation failures - check wiring connections, battery terminals | (not specified) | |
Clocks - Replacing replacement unit attaching wires - removal/return | 18th | |
Clocks, Electric accuracy - regulator operation | (not specified) | |
Clocks, Service Hints for Packard Electric installation, starting, regulating - replacement serviceWestclox, Jaeger | (not specified) | |
Clocks, Service on 1939 new vendor, Borg - third-party service | 17th | |
Clutch supplier issues - Borg/Beck, engine suffix identification | 18th | |
Clutch Relay Lever - Extra Lubrication Point Super Eight or Borg-Beck equipment - identification | 18th | |
Cold Weather drive belt removal - refrigerant pump-down | 18th-20th | |
Compartment Door, Instrument Board door stuck, pops open, rattles - new stiffer striker plate | 1800-1-1A-3-3A-4-5 | |
Compressors seized, corrosion - use of special oil, dehydrator | 18th-20th | |
Connecting Rod and Cap Assembly assembly orientation - crankshaft position | 120C-138CD; 115C; 1600-1-1A-1D; 1700-1-1A-2; 18th-20th | |
Connecting Rod Bolt Palnut cotter pins eliminated - new nut locks, proper tightening | 1700-1-2 | |
Connecting Rod Bolts - Palnuts eliminates cotter pins, not reusable - proper installation, new tool | 1700-1-2 | |
Connecting Rod Burnisher Change rod bushing, production change - tool modification required | 1700-1 | |
Connecting Rod Lock Nut Wrench new special tool - new style Pal nuts | 1700-1 | |
Control Arm Expander, Lower - Tool Correction socket number - T-handle wrench sold separately | (not specified) | |
Convertible: Binding, Top rust stains - new Hidem type, improved tacks | (not specified) | |
Convertible: Care, Tops cleaning, dressing - frequency | (not specified) | |
Convertible: Cleaning...Tops dry-brushing, water-rinse - grease removal | (not specified) | |
Convertible: Dressing, New Top spray-on rejuvenator - black tops | (not specified) | |
Convertible: Dressing, Top spray-on rejuvenator - black/olive tops | (not specified) | |
Convertible: Instructions, Top coupe/sedan - raise/lower | 1600 (1189); 1601 (1197-99) | |
Convertible: Rust Stains, Top electrolytic action - new Hidem binding, improved tacks | (not specified) | |
Convertible: Tops (Lock) lifting-off, lock loose - new tension spring, LH | 18th | |
Convertible: Tops (Lock) lifting-off, lock loose - new tension spring, RH | 19th (exc. 1951) | |
Convertible: Tops, (Assemblies) top skeleton only - order/tailor covers separately | (not specified) | |
Convertible: Windshield Leaks loose division bar screws - tighten or replace | 1800 (1389); 1801 (1397-99); 1803 (1377-79) | |
Cooling System, Care of the hot spots, detonation - inspection/flushing, rust inhibitor | (all models) | |
Courtesy Coats and Mechanics Suits Information on availabity and sizes | (not specified) | |
Courtesy Lamp Terminal - Correction incorrect application specified | 19th (exc. 1951) | |
Courtesy Lamp Terminal new terminal type in production (application error) | 19th (exc. 1951) | |
Courtesy Lights front compartment, instrument board - retrofit for early production cars | 19th (exc. 1951) | |
Covers, Car price change, not stocked - new dustless covers | (all models) | |
Covers, Car product information - paper, supplier | (all models) | |
Covers, Paper Car product information - new, moisture resistant | (all models) | |
Covers, Radiator and Fender Grille product information - cold weather operation, quick warm-up | 18th-20th | |
Cradle Assembly, Radiator Core - Parts Book Correction specified number not serviced - alternate | (not specified) | |
Crank, Transmission Checking new special tool suggestion - fabricate locally | (not specified) | |
Crankcase Sludge reduced driving, condensation, bearing trouble - operating temperatures, oil changes | (all models) | |
Crankshaft Journal Sizes bearing selection - exact dimensions provided | 18th-21st | |
Crankshaft Journal Sizes bearing selection - exact dimensions | 18th-21st | |
Cylinder and Piston Assemblies Available short block less crankshaft - back in stock | 1203-4-5; 1403-4-5; 120-138CD; 115C; 1600-1-1A-1D-2; 1700-1-1A-2; 18th-21st | |
Cylinder and Piston Assembly - Parts Book Correction part number | 1901-1A | |
Cylinder Blocks, Super Eight use of 16th Series - drilling valve compartment drains, additional parts | 15th | |
Cylinder Bore and Piston Diameter Marking Chart identification - location | 16th | |
Cylinder Head Combinations, Distributor and additional advance, requires different head - part reference | 1800 | |
Cylinder Head Corrosion aluminum - checks, maintenance, precautions | 12th-14th; 120-138CD; 115C; 15th-16th; 1707-8 | |
Cylinder Head Gasket Seal precoated - part reference | 7th-14th; 120-138CD; 115C; 15th-16th; 1700-1-2-3-5 | |
Cylinder Head Gaskets overheating - water passage blocked by sealing film | (not specified) | |
Cylinder Head Gaskets wartime shortage - re-use, precautions | (all models) | |
Cylinder Head Identification casting numbers - high/low compression | 16th | |
Cylinder Head Lifter Tool weight/length, bonnet design - new special tool required | 19th | |
Cylinder Head Nuts, Tighten head failures/leaks, oil consumption - proper replacement, torque-tightening | (all models) | |
Cylinder Head Nuts, Tightening oil consumption, poor economy/performance, cracked heads - tensioning wrench, procedure | (all models) | |
Cylinder Head Studs oversize threads, water jacket seal - identification, sealing paste | All Models | |
Cylinder Head Tension Wrench proper tightening reiterated - alternate special tools | (all models) | |
Cylinder Head, Mounting Electromatic Clutch on New support holes not drilled - layout, specifications | 1901 | |
Cylinder Heads new cast-iron, supersedes aluminum - redrilling not required | 1200-1-2; 1400-1-2; 1500-1-2; 1603-4-5 | |
Cylinder Heads return to cast-iron, gasket usage - replaces aluminum heads, drill new water passages | 120-138CD; 1601-1A-2-3-4-5; 1701-1A-2-3-3A-5 | |
Cylinder Heads on Super Eight, Aluminum corrosion/leaks - inspection service | 1500-1-2; 1603-4-5 | |
Cylinder Heads, Ordering high compression, superseded part - flange and other details required | 120C-138CD; 1601-2; 1701-2 | |
Cylinder Heads, Return Bolts Shipped with bundled for shipping - steel shortage | (all models) | |
Cylinder Repair Kits, Hydraulic Brake new kits - master and wheel cylinder | 120-138CD; 115C; 15th-16th | |
Cylinder Repairs small holes/cracks - repair compounds | (all models) | |
Cylinders and Valves, Rusted moving stored vehicles - preparations for starting | (all models) | |
Defroster - Right Hand new RH equipment - hose/deflector misalignment | 120C; 115C; 15th | |
Defroster Nozzle Fit new die cast part - file to fit moulding flange | 18th? | |
Defrosters maximum results - instructions, thermostat selection | 18th | |
Delco Distributor Tools New Service Tool Set | (not specified) | |
Deluxe Station Wagons Interior Changes | 1483DE, 1493DE | |
Detonation - Super Eight main metering jet size reduced, improves performance/consumption - octane reiterated | 1703-5 | |
Detonation, What to do About carbon formation, fuel octane - checks and adjustments, cleaning | (all models) | |
Differential Carrier Leakage loose carrier nuts - pinion/axle shaft seals | (not specified) | |
Differential Carrier Nuts oil leakage, copper gasket cupped - use of steel washer | (not specified) | |
Differential Gears and Pinions, New Type Revacycle teeth, superseded part - replace in sets | 1800; 1900 | |
Differential Pinion Bearing Preloading Scale revised to use standard tool - new socket required | (not specified) | |
Differential Ring Gear and Case ring gear bolts holes enlarged - drill case to match | 120-138CD; 115C; 1600-1; 1700-1-3; 1801-3 | |
Differential, Servicing the diagnosing noise - overhaul procedure | 120C-138CD; 115C; 16th-21st | |
Differential, Wire Gasket Designed to Stop Leaks at carrier retaining bolts - supersedes flat washer type | 120C-138CD; 115C; 16th-22nd | |
Directing Acting Shocks - Repair Kit Discontinured Information | (not specified) | |
Distributor - Tool Suggestions spread-nut holding tool | (not specified) | |
Distributor and Cylinder Head Combinations additional advance, requires different head - part reference | 1800 | |
Distributor Bracket Ratchet - Screw Driver Socket new special tool - timing adjustment | 120-138CD; 115C; 1600-1 | |
Distributor Governor and Vacuum Advance insufficient reading - proper testing | 120C-138CD; 115C; 16th-54th | |
Distributor Points, Adjusting contact faces, rubbing block adjustment - point dressing/tension | 1st-14th; 120-138CD; 115C; 15th18th | |
Door Bumpers upper corner, anti-rattle - field installation | 1600-1-2 | |
Door Locks, Frozen ice formation - thawing, lubrication | (not specified) | |
Door Straightening tool suggestion - fabricate locally | (not specified) | |
Dragging Brakes excess fluid in lines - master cylinder checks/corrections | 120-138CD; 115C; 15th-20th | |
Drain Plug Wrench - Special Tools new required tools- transmission and Econo-Drive | 18th | |
Drive Shaft Clunk shaft shifting on splines - reduce driveline angle, new rear axle wedge | 18th | |
Drive Shafts, Dont Fill...with Grease noise deadening - premature u-joint failure | (not specified) | |
Driven Plates, Clutch (Electromatic) different sizes, not interchangeable - parts reference, identification | 1900-1 | |
Driving Pinion Bearing Sleeve crush groove omitted - inspect, return | 1801-1A-3-3A-4-5-6-7-8; 1900-1-1A-3-3A-4-5-6-7-8; 1951; 2003-06; ?2004-05-07-08-23-30-55 | |
Drum Seals, Brake dust/water shield attachment - drain hole provision | 120C; 115C; 1500-1-2 | |
Econo-Drive Lubrication changes in pilot bearing, thrust washer - hypoid oil permitted, unit identification | 1700-1-2-3-5 | |
Econo-Drive Lubrication hypoid oil approved - new plugs/tag | 1700-1-2-3-5 | |
Electrical Equipment - Ordering Parts Delco-Remy vs. Auto-Lite - supplemental parts list pages issued | 120C; 115C; 15th | |
Electromatic: Adjusting...the Clutch common mistakes - linkage stops, spool rod, body plug | 19th-20th | |
Electromatic: Adjustment engagement characteristics - preferred settings | 19th | |
Electromatic: Aero-Drive Indicator Light on when standing - fuse check | 19th-20th | |
Electromatic: Carburetor Control Linkage Equipment choke, start switch, clutch issues - lost motion, service parts kit (all models) | 20th | |
Electromatic: Carburetor Control Linkage Equipment choke, start switch, clutch issues - lost motion, service parts kit | 20th | |
Electromatic: Clutch Driven Plates different sizes, not interchangeable - parts reference, identification | 1900-1 | |
Electromatic: Clutch Instructions superseded, discard - illustrations renumbered, adjustments/checks revised | 19th | |
Electromatic: Clutch Relay Lever control valve squeak, sticky throwout - relay lever bearing adjustment | 1900-1 | |
Electromatic: Clutch Screw Driver and Wrench new special tool - first/reverse solenoid | 19th | |
Electromatic: Clutch Screw Driver and Wrench redesigned for new taper head screw | 19th | |
Electromatic: Clutch Valve Adjustment erratic performance, sticky spool rod/sleeve - clean, never lubricate | 19th-20th | |
Electromatic: Clutch Valve Adjustment lost motion - install valve linkage spring, clean spool rod | 19th-20th | |
Electromatic: Clutch, Packard... - Owner's Instructions instructions, theory of operation - schematic, adjustments/checks | 19th | |
Electromatic: Disengagement sticking in high gear, decelerating - governor switch | 19th | |
Electromatic: Failure to Release stalling - governor circuit switch checks/adjustments | 19th-20th | |
Electromatic: Mounting...on New Cylinder Head support holes not drilled - layout, specifications | 1901 | |
Electromatic: No-Rol, ...and incompatibilities - not recommended together | 19th | |
Electromatic: Red Pedal Pads back in stock - easy equipment identification | 19th-21st | |
Electromatic: Wiring constant battery drain - governor/ignition switch wires | 19th | |
Electromatic: Wiring Diagram, Clutch new model information - Other Models | 20th (exc. 2000-01-03-06-10-11) | |
Engine and Adapter Kit, Six Cylinder Replacement now in-stock for Electromatic and prior to 19th - new crankcase ventilator kits | 115C; 1600; 1700; 1800; 1900; 2000-10-20-30; 2100-30 | |
Engine Replacement (U-Joint) Henney models - new shorter, front drive shaft available | 1701A; 1801A; 1901A; 2001A | |
Engine Replacement - Right-Hand Drive Retrofitting a 288 into Clippers and 1601 | 1601, Clippers | |
Engine Replacement Kits 288 Engine Retrofits for 1938-1942 cars | 2001, 1951, 1601, 1701, 1801, 1901 | |
Engine Replacement Kits Engine Retrofits for 1938-1942 cars - Updated | 2001, 1951, 1601, 1701, 1801, 1901 | |
Engine Replacement Kits Engine Retrofits for 1938-1942 cars | 1601, 1701, 1801, 1901, 1951, 2001, 2101 | |
Engine Replacement, Six Cylinder - Correction standard passenger cars - engine part number | 115C; 1600; 1700; 1800; 1900; 2000-10-20; 2100 | |
Engine Replacement, Six Cylinder new improved design services all models - alterations required | 115C; 1600; 1700; 1800; 1900; 2000-10-20-30; 2100-30 | |
Engine Stand and Dolly new tools - six/eight-cylinder | (not specified) | |
Engine Stand Price supplier increase | (not specified) | |
Engine Vibration Different Causes of Vibration | (not specified) | |
Engine, Prelubricate Replacement oiling cylinder walls - break-in | (all models) | |
Exhaust Noise Bumper Guards | (Not Specified) | |
Factory Replacment Engines Update, Modfications | 110, 115-C, 120 | |
Fan Belt Renewal shorter belt life - inspection | (all models) | |
Fans, Heavy Duty low speed cooling - applications expanded | 1700-1-1A-7; 1800-1-1A; 1900-1-1A; 1951; 2000-01-11; 2100-01-11-30 | |
Fans, Service severe use - new extra-capacity, oversize fan | 1600-1 | |
Fender Grille Covers - New Accessories cold weather - improved motor/heater performance | 18th | |
Fender Guards product information - front/rear | 1900-1 | |
Filters (Refrigerant) two types - interchange directions | 18th-20th | |
Finger Adjustment Dimensions, Clutch reference - special tool | 120-138CD; 115C; 15th-20th | |
Flange Nuts, Special Tool to Help Mechanic Tighten or Loosen Universal Joint new holding tool | 120-138CD; 115C; 16th-22nd; (23rd-25th) | |
Flange Nuts, Universal Joint new special tool - thin-walled socket | 120C-138CD; 115C; 1600-1-2 | |
Flat Rate Manual 1941-49, Changes and Corrections in clutch pedal booster spring | 19th-23rd | |
Flat Rate Manual 1941-49, Changes and Corrections in select operations | 19th-23rd | |
Flood Zones, Cars in dirt carried in - drain/refill differential, clean/repack wheel bearings | (all models) | |
Flywheel Housing Clutch Shifter Relay Pivot Puller new special tool - due to clutch relay lever change | 1600-1-2 | |
Flywheel Housing Covers cast design replaces stamped steel | 120-138CD; 115C; 1600-1-1A-1D-2; 1700-1-1A-2; 1800-1-1A; 1900-1-1A; 1951; 2000-01-11-10-20-21-30; 2100-01-11-30 | |
Fog Lights with Stone Shields, Installing front bumper shield added - modification | 19th (exc. 1951) | |
Fog Lights, Sealbeam product information - benefits, proper wiring | (not specified) | |
Foot Rest Rim Moulding product information - protects carpet, sedan models | 1602 (1190-91); 1702 (1290-91); 1804 (1362); 1805 (1370-71); 1807 (1332-42); 1808 (1350-51); others? | |
Friction Lag, Measuring clarification | 1700-1-2-3-5 | |
Front End Equipment alternate, portable tools | (all models) | |
Front End Specifications alignment - reference chart | 120C; 115C; 15th-20th | |
Front Fender - Now Available had been difficult to procure | 1801-1A-3-3A-4-6-7 | |
Front Fender Flaps body protection - procure locally | (not specified) | |
Front Spring Adaptors usage with 4-1/2-in. springs - replacing 4-in. | 1801-1A-3-3A-4-5-6-7-8; 1901-1A; 2021 | |
Front Spring Identification - 1937 Models specifications - part reference | 120C; 115C; 15th | |
Front Spring Squeaks squeaks/clicks - reindexing bottom tapered end | 1800-1-3-6 | |
Front Spring Striking-Through compression bumper gives way - shim fabrication/installation | 1800-1-3-6 | |
Front Springs early, short springs superceded, spacer eliminated - identification | 1601 | |
Front Stabilizer Service Links new tubular type - eliminates rattles | 1800-1-3-6; 19th; 2000-01-03-06-10-11-20-21-23; 21st-22nd | |
Front Suspension Parts - Master Part List Correction clarification - hearse/ambulance/bus applications | 1701A-03A; 1801A-03A; 1901A-03A | |
Front Wheel Camber - Correction Safe-T-fleX, upper support arm - spacer part number | 120-120C; 115C; 15th | |
Front Wheel Camber Safe-T-fleX, upper support arm - offset pilots vs. spacers, specifications | 120-120C; 115C; 15th | |
Front Wheel Toe-In extreme variation - front wheel support arm inner bushing | 120-120C; 115C 1500; 1506-7-8 | |
Front Wheel Toe-In special tools required for pin bushing replacement - redesigned, rework locally | 120-120C; 115C 1500; 1506-7-8 | |
Front Window - Water Deflector Production Change, Retrofit | 12th Series | |
Fuel Economy, Notes on carburetor adjustments, choke operation, heat control valve spring, octane | (not specified) | |
Fuel Pump Air Dome improper installation - metal chips in pump, carburetor | 1700-1-1A-2 | |
Fuel Pump Air Dome new tee fitting included - eliminates drilling | 1700-1-1A-2 | |
Fuel Pump Filter new disc type, interchangeable with screen type - cleaning | 17th | |
Fuel Pump Inlet Hose weak flow, twisted/restricted - proper installation, telltale | (not specified) | |
Fuel Pump Noise kinked/restricted hose or tube | (not specified) | |
Fuel Pump Repair Kit, Motor new kit available - Seniors | ?901-2-3-4-5-6; 10th-15th; 1603-4-5-7-8 | |
Fuel Pump Screen edge type - cleaning/inspection | (not specified) | |
Fuel, Anti-Knock Super Eight, Twelve motors, performance/mileage, octane/timing | ?9th-16th | |
Fuels Super Eight, Twelve motors - performance/economy, octane/timing reiterated | ?9th-16th | |
Garnish Moulding Screws screws lose, holes enlarged - No. 8 screw with No. 6 head | (all models) | |
Gas Consumption in Cold Weather wartime rationing - shortening warm-up period | (all models) | |
Gas Gauge Reading on 1937 Models incorrect - paint on tank unit terminal | 120C, 115C; 15th | |
Gas Mileage. Checking handling complaints, gas-per-mile gauge | (all models) | |
Gas Tank Removing proper procedure | 19th | |
Gas Tank, To Remove proper procedure, bend frame lip - production change | 2004-05-07-08-20-21-23 | |
Gasket Sets, Transmission parts available for service - part reference | 120-138CD; 115C; 1600-1-2; 1700-1-2-3-5; 18th-22nd | |
Gasket Sets, Transmission and Overdrive parts available for service - part reference | 17th-22nd | |
Gasoline expected changes in octane, volatility - effects, compensation | (all models) | |
Gasoline Economy rationing - carburetor adjustments, float level, spark advance, octane | (all models) | |
Gasoline Economy spark advance, carburetor jets - operating conditions | (all models) | |
Gasoline Gum sticky engine valves - formation, prevention, proper cleaning | (all models) | |
Gasoline Mileage Testing new special tool - installation/use, accuracy | (all models) | |
Gasoline Tank - Parts List Correction applications corrected | 18th | |
Gasoline Tank Gauge Tester new special tools - required | 1600-3 | |
Gasoline Tank Gauges float arm bent in shipment - level settings | 120-138CD; 115C; 1500-1-2-7-8; 16th | |
Gasoline Tank Gauges float arm bent in shipment - level settings | 120-138CD; 115C; 15th-18th; 19th (exc. 1951) | |
Gasoline Tank Gauges float arm bent in shipment - level settings | 120-138CD; 115C; 1500-1-2-7-8; 16th-20th | |
Gasoline, Low Octane spark knock, preignition - remedies, trade-offs | (all models) | |
Gasoline, Oil in low oil consumption, sticking valves - oil as an additive, rust inhibitor | (all models) | |
Gasoline, Water In ice formation - cleaning, prevention | (all models) | |
Gear Clash, Second Speed synchronizer operation - bearing lock ring burrs | 17th-54th | |
Gear Shift - Tool Number Correction linkage adjustment - steering aligning gauge | 19th | |
Gear Shift stiff, difficult - linkage alignment/adjustment | 19th | |
Gear Shift Anti-Rattler additional instructions - clearing steering gear dowel | 17th-18th | |
Gear Shift Anti-Rattler rubber anti-rattle button - 19th Series retrofit | 17th-18th | |
Gear Shift Lever Rattle bell crank - lubrication causes excessive movement | 17th | |
Gear Shift Levers (Handishift) alignment holes - lock rod for service safety | 1700-1-2-3-5 | |
Gear Shift Linkage shift lever drag - loose interlock block, levers, forks | 17th-20th | |
Gear Shifter Forks superseded design - larger pins/holes | 17th-20th | |
Gear Shifter Lever Rattle column production changes - anti-rattle spring/plug | 1700-1-2-3-5 | |
Gear Shifting in Cold Weather trouble - use of seasonal oils | (not specified) | |
Gear Shifts, Dont Fall Down on Fixing sticking in gear - summary of checks/adjustments | 17th-20th | |
Gears, Damage to Transmission...from Shifting gear clash - consequences | (not specified) | |
Gearshift Still Sticks, That lost motion reiterated - new forged column levers | 18th-21st | |
Gearshift Still Sticks, That lost motion, levers/interlock - column lever clearance | 18th-20th; (21st) | |
Generator Brush Set complete line now available | 120-138CD; 115C; 1500-1-2; 1600-1-2-3-4-5; 1700-1-2-3-5 | |
Generator Charging Rate two- vs. three-brush types - ammeter needle indications | 120C; 115C; 15th | |
Generator Pulleys rundown batteries, low speed driving - new smaller pulleys, faster rotation | 120C; 115C; 1600; 1700-1 | |
Generators and Regulators new two-pole, shunt-wound system - operation, precautions, checks | 18th | |
Glass, Heat Treated new, tempered safety glass - properties, rear window only | 16th | |
Glass, Moisture on inside, steaming/frosting - ventilation, defroster | (not specified) | |
Grabbing Brakes linings superseded - dust accumulation reiterated | 1700-1 | |
Grabbing Brakes severe brake action - dust accumulation, rework primary lining | 1700-1 | |
Grease, Save the - Rear Springs rubber/Silenite deterioration | 1600-1-2; 1702-3-3A; 18th-22nd | |
Hand Brake Cable Assemblies - Items Now Available back in stock | 1700-1-2-3-5; 1801-3-4-5-6-7-8; 19th | |
Hand Brake Cables frayed, broken - cleaning, lubrication | 120-138CD; 115C; 15th-20th | |
Hand Brake Lever Replacements superseded parts - modification for 16th-18th | 1600-1-1A-1D-2-7-8; 17th-20th | |
Hand Brake Lever Spring (Tool) tool suggestion - fabricate locally | 16th; (17th) | |
Hand Brakes, Frozen water in lever cable conduit - use of 19th Sr. boot | 120-138CD; 115C; 15th-18th | |
Head Light Door Gasket serviced separately from bezel - installation | 19th (exc. 1951) | |
Headlamp Aiming - Super Eight multi-beam headlamps - corrected instructions | 1703-5 | |
Headlamp Unit Wrench new special tool - slotted for headlight cable | 1600-1-3-8 | |
Headlamps, How to Use the New (Sealed Beam) upper/lower beams - light/foot switch operation | 18th | |
Headlight Switch - Super Eight and Twelve improved access for service - removal procedure | 15th | |
Headlight Switch, Instrument Board shaft interference, switch body distorted - instrument panel spacer | 1600-1-1A-1D-2 | |
Headlight Tester new service tool | (all models) | |
Headlights, New Style Sealed Beam improved design - use in pairs | 18th-54th; 55th-56th | |
Headroom Increased lowering front seat adjusters - raising steering wheel position | 1600-1-2 | |
Hearse and Ambulance Specifications new cover/title - Special Edition Commercial Chassis | 1701A-3A | |
Heat Control (Valve), Automatic engine performance - operation, checks and correction | 1001-2-3-4; 1100-1-2-3-4-5; 1200-1-2-3-4-5; 1400-1-2-3-4-5; 120-138CD; 115C; 1500-1-2; 1600-1-1A-1D-2-3-4-5; 1700-1-1A-2-3-3A-5; 18th-21st | |
Heat Control (Valve), Check That sticking, adjustment - repair kits available | 1001-2-3-4; 1100-1-2-3-4-5; 1200-1-2-3-4-5; 1400-1-2-3-4-5; 120-138CD; 115C; 1500-1-2; 1600-1-1A-1D-2-3-4-5; 1700-1-1A-2-3-3A-5; 18th-20th | |
Heat Control Valve, Carburetor sticking, carbon/corrosion - shaft clearance | 1001-2-3-4; 1100-1-2-3-4-5; 1200-1-2-3-4-5; 1400-1-2-3-4-5; 120-138CD; 115C; 1500-1-2; 1600-1-1A-1D-2-3-4-5; 1700-1-1A-2-3-3A-5; 18th-20th | |
Heat Control Valve, Sticking proper diagnosis - rust, lubrication, spring tension | 1001-2-3-4; 1100-1-2-3-4-5; 1200-1-2-3-4-5; 1400-1-2-3-4-5; 120-138CD; 115C; 1500-1-2; 1600-1-1A-1D-2-3-4-5; 1700-1-1A-2-3-3A-5; 18th-20th | |
Heat in Car Interiors battery box cover off - proper fastening | All Models | |
Heat in Cars battery box cover off - proper fastening, reiterated | All Models | |
Heater Operation thermostat/antifreeze usage - fan control switch | 16th | |
Heater Program Information | (not specified) | |
Heater Switch, Proper Use of hang tag - instructions | (not specified) | |
Heater, Underseat front seat back rest support interference - seat track-to-floor-pan spacers | 19th | |
Heaters - Defrosters, Installing Hot Water procedures updated - illustrated | 17th | |
Heaters, Rear Compartment X-member limits usage - body type reference | 16th-17th | |
Heaters, Rear Compartment Hot Water additional instructions - location | 17th (1272-82-92) | |
History Correction, Clutch substitution of Long driven plate - not pressure plate | 18th | |
History, Clutch driven/pressure plate suppliers - not interchangeable, part reference | 18th | |
Hood Holding Board body hook omitted, tool suggestion - fabricate locally | 120C; 115C; 15th | |
Horn Button and Emblem - Now Available had been difficult to procure | 17th-18th | |
Horn Diaphragm - Parts Book Correction supplier numbers - applications | 16th | |
Horn Ring Rattle rough roads - shim/stretch support spring | 19th-20th | |
Hose Cutter, Rubber new special tool - bulk hose | (all models) | |
Hose, Radiator Inlet (Upper) molded hose not available - new bendable straight hose | 19th-20th | |
Hose, Radiator Upper (Inlet) split, collapsed - sealed systems cap failures | 18th-20th | |
Hub and Drum Assemblies - Parts Now Available back in stock - front and rear | 115C; 1600; 1700; 1800 | |
Hub Shell Covers, Emblems for cloisonne upgrade for standard cover | 20th | |
Hydraulic Tappet Checking Tool cleaning, testing - new tool | 1803-3A-4-5-6-7-8; 1903-3A-4-5-6-7-8; 2003-04-05-06-07-08-23-30-55; 2103-06-26; 2206-13-26-33; 2306-13-33 | |
Hydraulic Tappets - Super Eight operation, diagnosis, service - new high-volume oil pump | 1803-3A-4-5-6-7-8; 1903-3A-4-5-6-7-8; 2003-04-05-06-07-08-23-30-55; 2103-06-26 | |
Hydraulic Tappets new, automatically adjusted - removal/handling, troubleshooting noise | 1803-3A-4-5-6-7-8 | |
Hydraulic Valve Lifter Tester checking leak-down - new tool | 1803-3A-4-5-6-7-8; 1903-3A-4-5-6-7-8; 2003-04-05-06-07-08-23-30-55; 2103-06-26; 2206-13-26-33; (2306-13-33) | |
Hydraulic Valve Tappets - Super Eight noisy, low oil pressure at idle - plumbing change, verify filter restrictor | 1803-3A-4-5-6-7-8; 1903-3A-4-5-6-7-8 | |
Hypoid Gear Lubrication approved lubricant - recommended service | (not specified) | |
Hypoid Gear Lubrication special lubricant - recommended service | (not specified) | |
Hypoid Gear Lubrication, Tell Your Customers About reiterated - suggested customer letter | (not specified) | |
Identification Chart, Packard Body model identification - chassis/body/motor numbers | 120-138CD; 115C; 1600-1-1D-2; 1700-1-2-3-5; 18th-20th | |
Identifying Numbers, Packard motor/engine, vehicle/serial, body | 6th-14th; 120-138CD; 115C; 15th-21st; (22nd-23rd) | |
Idle, Engine - Twelve mounting changed - shim for service | 1207-8; 1406-7-8; 1506-7-8; 1607-8 | |
Idle, Poor vacuum booster leaks - cover gasket, diaphragm checks | 17th | |
Ignition Breaker Points hard/no starting, blued/oxidized points - high capacity condensor, regulator adjustment | 1800 | |
Ignition Cut Out Econo-Drive, decelerating - relay adjustment | 18th-20th; (21st) | |
Ignition Cut-Out Aero-Drive, decelerating - relay point checks/adjustments | 18th-19th | |
Ignition Cut-Out Econo-Drive - relay adjustment/check | 18th | |
Ignition Drowning Out water - new coil/plug insulators, ignition wire sealing compound | All Models | |
Ignition Point Grinder new special tool - in-car service | (all models) | |
Ignition Timing specifications change - high compression heads only | 1600 | |
Inspections, 1000 and 3000-Mile dealer responsibilities - customer handling | (not specified) | |
Instructions illustration correction, page reprint - Service Instruction booklet | 19th; (20th) | |
Instructions, Packard...Operation, Service and Owners new model information | 19th; (20th) | |
Interlock, Transmission Cover shift interlock block loose/worn - new service kit | 17th-20th | |
Intermediate Drive Bearing - Periodic Noise highway speeds, misalignment - neutralize mounting | 1601A-2 | |
Jack, Use of owner education - placement illustrated | 19th (exc. 1951); 2004-05-07-08-20-21-23-30-55 | |
Knock, Fuel hot weather, reduced octane - checks/adjustments | (not specified) | |
Lamp (License) Rear Compartment Lid Lock Handle Assembly superseded - now includes small detail parts | 1800-1-3 | |
Lamp Bulb Pliers new special tool - grips bulb base | (all models) | |
Lamps, Fender and Tail parts list, shop manual error - polarized bulb base, applications clarified | 18th | |
Lateral Stabilizer position - new clamping parts | 1600-1-2 | |
Lateral Stabilizer rear sway control - reconnecting | 1600-1-2 | |
Leaks, Repairing Cooling System Wonderweld utility item - proper use | All Models | |
License Data and Capacity Information - Correction cooling system capacity - incorrect units | 18th | |
License Data and Capacity Information reference chart | 12th-14th; 120-120C; 115C; 15th | |
License Data and Capacity Information reference chart | 12th-14th; 120-120C; 115C; 15th-17th | |
License Data and Capacity Information reference chart | 12th-14th; 120-120C; 115C; 15th-18th | |
License Data and Capacity Information reference chart | 18th-20th | |
Lining, Brake Marshall lining - difference in material/length, primary/secondary | 120-138CD; 115C; 1600-1-1D; 1700-1 | |
Lining, Brake more uniform action, longer life - identification, use | (all models) | |
Linkage Equipment, Carburetor Control choke, start switch, clutch issues - lost motion, service parts kit (all models) | 20th | |
Linkage Equipment, Carburetor Control choke, start switch, clutch issues - lost motion, service parts kit (Electromatic) | 20th | |
Linkage, Clutch lost motion, disengagement - linkage wear, use of 1900-01 parts | 1600-1; 1700-1; 1800-1 | |
Linkage, Clutch squeaks rattles, clutch relay lever - washers/springs added, retrofit | 1600-1-2 | |
Linkage, Handishift sticking in gear - interlock block, linkage assist spring | 19th-20th | |
Linkage, Lost Motion in Handishift sticking in low, shifting to neutral - worn rubber grommets, new steel bushings | 17th | |
Linkage, Lost Motion in Throttle starting difficulty - effect on starter switch, choke | 1951; 20th; (21st-26th) | |
Locking in Gear - see also: Gear Shift (Gearshift) Interlock Linkage Lubricant Sticking in Gear | -- | -- |
Locking in Gear sticking in low, shifting to neutral - clutch free play, shift lever clearance | 18th-19th | |
Locking in Gear sticking in low, shifting to neutral - spring washer eliminated, new shims for lever clearance | 18th-19th | |
Lubricant, Rear Axle production fill, break-in properties | (not specified) | |
Lubricant, Transmission seasonal oils - viscosity issues | (all models) | |
Lubricants, Transmission warm weather, bearing noise - new Kendall 400 oil | (not specified) | |
Lubricate How Often? reduced driving, slower speeds - crankcase condensation | (all models) | |
Lubrication SAE viscosity ratings, reference charts - interval reiterated | 20th | |
Lubrication Charts new model information | 17th | |
Lubrication Charts new model information | 18th | |
Lubrication Charts new model information | 19th (exc. 1951) | |
Lubrication Charts new model information | 20th (exc. 2000-01-03-06-10-11) | |
Lubrication Inspection Procedure details - proper order | (all models) | |
Lubrication Stickers door jamb maintenance record - reiterated | (all models) | |
Lubrication Stickers new door jamb maintenance record - alignment, tire rotation | (all models) | |
Lubrication, Front Universal Joint ball-and-trunnion type - identification, interval | 1900; 2000 | |
Lubrication, Note on additional service points | (all models) | |
Lubrication, Transmission - Econo-Drive summer/winter - viscosity issues, draining/filling | 17th; (18th) | |
Lubricator Connector, Reservoir Type special grease fitting - irregular service interval | (not specified) | |
Luggage Compartments, Flock Liner for new bulb-type gun, procedure, materials | 17th | |
Manifold Gasket Failures chafing - chamfer manifold edges | (all models) | |
Manifold Gasket Leakage mating surface inspection - realignment procedure | 18th | |
Manifold Gasket Leaks, Intake rough idle - improper tightening, detection | (all models) | |
Manifold Gasket Sets now available | 17th | |
Manifold Gaskets, Exhaust order in sets only - superseded parts | 120-138CD; 1601-1-1A-1D; 1701-1A; 1801-1A; 1803-3A-4-5-6-7-8 | |
Manifold Removal, Exhaust difficulty - proper procedure | 1803-3A-4-5-6-7-8 | |
Manifold Swivel Socket Wrench, Inlet and Exhaust new special tool - water jacket rear drain plug | 1701-2 | |
Manifold, Intake and Exhaust no joint gasket - use gasket paste | 1700-1-2 | |
Master Cylinder Wrench, Brake new special tool - filler plug | 120-120C; 115C; 15th | |
Mechanical Specifications and Adjustments - Changes new model information - corrections | 16th | |
Mechanical Specifications and Adjustments - Changes and Corrections new model information | 18th | |
Mechanical Specifications and Adjustments - Correction new model information - caster angle specifications | 19th (exc. 1951) | |
Mechanical Specifications and Adjustments - Standard Size Correction wheelbase | 1808 | |
Mechanical Specifications and Adjustments new model information | 120C; 115C; 15th | |
Mechanical Specifications and Adjustments new model information | 16th | |
Mechanical Specifications and Adjustments new model information | 17th | |
Mechanical Specifications and Adjustments new model information | 18th | |
Mechanical Specifications and Adjustments new model information | 19th (exc. 1951) | |
Mechanical Specifications and Adjustments new model information | 20th | |
Mechanical Specifications and Adjustments Corrections new model information | 120C; 115C; 15th | |
Methyl Chloride in...Systems (Refrigerant) wartime shortage, Freon substitute, mixing, precautions | 18th-20th | |
Mirror, Rear View obstructed view, closed cars - mounting position raised, /i> | 1600-1 | |
Miss, High Speed fuel starvation - install Super Eight air dome | 1700-1-1A-2 | |
Moth Spray and Moth Crystals product information - vehicle storage, upholstery protection | (all models) | |
Motor Numbers, Record of Packard cross-referenced by model | 1st-14th; 120-138CD; 115C; 15th-16th | |
Motor Oil New Recommendations | (Not Specified) | |
Motor Period torsional disturbance - clutch/transmission jazz | (not specified) | |
Motor Snubber Links, Loose washer omitted/incorrect - parts needed, installation | 1700-1-3 | |
Motors in Cars in Storage, Lubrication of new vehicles - rust inhibitor | 20th | |
Muffler Corrosion condensation, short trips | (not specified) | |
Muffler Outlet Tube, Exhaust - Now Available had been difficult to procure | 1700-1 | |
Muffler, Exhaust - Now Available previously difficult to procure | 2000-10; 2100-30 | |
Muffler, Exhaust front tube now attached - part reference | 1500-1-2-7-8; 1603-4-5-7-8 | |
New Car Fitting and Delivery inspections, paperwork - data plate | (not specified) | |
No-Rol Installation control valve clutch lever modification - drawing | 1900-1 | |
Oil Additives, Use Of not endorsed - low viscosity, inadequate lubrication | (all models) | |
Oil Consumption sustained high speeds, rear vent tube - valve cover plates with baffles | 1600-1 | |
Oil Consumption, Fuel Pump May Cause High rough idle - fractured booster diaphragm | (not specified) | |
Oil Filler Pipe, Motor sticky valves - new longer design, improved crankcase ventilation | 19th | |
Oil Filter - Super Eight noisy lifters - special filter, blow-off valve | 1803-3A-4-5-6-7-8 | |
Oil Filter Cartridge - Change Period Revised high-detergents oils - reduced | 120-138CD; 115C; 16th?-54th | |
Oil Filter Cartridge Change Period Revised high detergent oil - reduced interval | 120-138CD; 115C; 16th?-54th | |
Oil Filter Connections, Purolator loose bracket - leaky unions, pipe failure | (not specified) | |
Oil Filter Installation, Purolator (What is Wrong with This Picture) wrong tube/cap - crankcase ventilation, vehicle storage | 19th | |
Oil Filter Leaks case cover gasket shrinkage - check tightness, do not reuse | 18th | |
Oil Filter Tubes leaking - new tube (Six), new tube/elbow (Super Eight) | 1800; 1803-3A-4-5-6-7-8 | |
Oil Filter, Super Eight - Correction incorrect part number | 1803-3A-4-5-6-7-8 | |
Oil Filter: Purolator Filter Facts micronic filtration, pleated paper - benefits, replacement period | (not specified) | |
Oil For Sub-Zero Operation, Winter Engine new 5-W oil - issues, limited availability/use | (all models) | |
Oil Gauge Sending Unit optimal orientation - locating marks | 1803-3A-4-5-6-7-8; 1903-3A-4-5-6-7-8; 1951; 2000-01-03-06-10-11; (21st) | |
Oil Leaks, Front Cover excessive oil consumption - checks/corrections/precautions | (not specified) | |
Oil Noise telegraphing through line/gauge - smaller diameter tube equipment | 1600-1-2 | |
Oil on Clutch Hubs, rear main bearing return leak - oil pan stud, copper washers | 18th | |
Oil Pan Gasket Sets replace RH-LH, together - available in sets | 120-138CD; 115C; 1600-1-1A-1D-2; 1700-1-1A-2; 18th-22nd; (23rd54th) | |
Oil Pan, Motor standard pan shortage - Clipper pan retrofit, indicator calibration | 120-138CD; 1601-2; 1701-2; 1801-1A; 1901-1A | |
Oil Pan, New pan, indicator, strainer bracket - new design, not interchangeable | 1900-1-1A | |
Oil Pressure Gauge, Erratic electric type - theory of operation and diagnosis | 1803-3A-4-5-6-7-8; 1903-3A-4-5-6-7-8; 1951; 2000-01-03-06-10-11; (21st) | |
Oil Pressure Reading electric type, incorrect - diagnosis | 1803-3A-4-5-6-7-8; 1903-3A-4-5-6-7-8; 1951; 2000-01-03-06-10-11; (21st) | |
Oil Pressure, Low - Correction part numbers | 1803-3A-4-5-6-7-8; 1903-3A-4-5-6-7-8; 2003-04-05-06-07-08-23-30-55; 2103-06-26 | |
Oil Pressure, Low idling, worn/sticking regulator valve - new spring-loaded type | 1803-3A-4-5-6-7-8; 1903-3A-4-5-6-7-8; 2003-04-05-06-07-08-23-30-55; 2103-06-26 | |
Oil Pressure, Low pan sludge, clogged pickup - cleaning procedure | (not specified) | |
Oil Pump - Twelve noisy valvetrain at start-up - metering valve sticking | ?1005-6; ?1106-7-8; ?1207-8; ?1406-7-8; ?1506-7-8; ?1607-8; 1707-8 | |
Oil Pump Body Cover - Now Available had been difficult to procure | ?1100-1-2-3-4-5; 1200-1-2-3-4-5; 1400-1-2-3-4-5; 1500-1-2; 1603-4-5; 1703-3A-5 | |
Oil Pump Camshaft Gear sheared drive gear pin, rust - use of thicker drive spring | 120-138CD; 115C; 1600-1; 1700-1-2; 18th-20th | |
Oil Pump Cover Kit, Motor Super Eight - new repair kit available | 1803-3A-4-5-6-7-8; 1903-3A-4-5-6-7-8; 2003-04-05-07-08-23-55 | |
Oil Pump, New Super Eight increased flow and pressure - worn pump or opening up of bearing clearances | 1803-3A-4-5-6-7-8; 1903-3A-4-5-6-7-8; 2003-04-05-06-07-08-23-30-55; 2103-06-26 | |
Oil Seal, Crankshaft Rear - Correction Master Part List application/number- molded rubber type | 1803-3A-4-5-6-7-8 | |
Oil Seal, Gear Cover burned, leaking - graphite grease | 120-138CD; 115C; 16th-54th | |
Oil Seal, Rear Bearing new -all composition type - service installation, rear oil pan copper washers | 1803-3A-4-5-6-7-8 | |
Oil Seal, Rear Main Bearing leaks - preventative measures | 120-138CD; 115C; 16th-18th (exc. 1703-3A-5); 1951; 2000-01-03-06-10-11; 21st; 22nd-24th; (25th-54th) | |
Oil Seal, Rear Main Bearing leaks - undersize | 120-138CD; 115C; 16th-18th (exc. 1703-3A-5); 1951; 2000-01-03-06-10-11; 21st; 22nd-54th | |
Oil Seal, Rear Main Bearing leaks, bearing distortion - new cork type, installation | 120-138CD; 115C; 16th-18th (exc. 1703-3A-5); 1951; 2000-01-03-06-10-11; 21st; 22nd-54th | |
Oil Seals damage, leaks - special tools, proper use | 19th-24th | |
Oil Seals, Leather dry installation damage - soak in engine oil | (all models) | |
Oil, Rust Inhibiting motors in storage - limited availability, alternate sourcing | 20th | |
Optional Paint and Upholstery Schemes 1941 Information | 19th Series | |
Overdrive: Assemblies, Transmission and... no longer available - replace with standard transmission | 1703-5 | |
Overdrive: Bearing Pre-Load, Econo-Drive new spring washer, spacer - identification, installation | 1700-1-2-3-5 | |
Overdrive: Bearing Preload, Econo-Drive preload washers - cotter pins eliminated | 1700-1-2-3-5 | |
Overdrive: Cars, Econo-Drive new preload parts - first use, unit serial numbers | 1700-1-2-3-5 | |
Overdrive: Control, Econo-Drive adjusted too short - minimum knob/stop clearance | 17th | |
Overdrive: Cut-In Speeds, Econo-Drive higher speed governor, special service unit - part reference | 18th | |
Overdrive: Electromatic, Aero-Drive with delayed shift, second gear - proper operation | 19th | |
Overdrive: Failure To Get Into... checks - corrections | 17th-20th | |
Overdrive: Flange Nuts, Special Tool to Help Mechanic Tighten or Loosen Universal Joint new holding tool | 17th-22nd; (23rd-25th) | |
Overdrive: Free Wheeling Clutch roller clutch inoperative - springs reversed | 1700-1-1A-2-3-3A-5; 1800-1-1A; 1900-1-1A; 1951; 2000-01-10-11; (2100-01-11) | |
Overdrive: Governor Switch, Econo-Drive difficulty getting into reverse - lockout knob check for inoperative switch | 18th | |
Overdrive: Governor Switch, Econo-Drive flickering dash light, clicking solenoid - switch shaft worm gear, transmission driving gear | 18th | |
Overdrive: Governor Switch, Econo-Drive locked out of reverse, switch mechanism binding - realign guide pin | 18th | |
Overdrive: Governor Switch, Econo-Drive no reverse - guide pin adjustment reiterated | 18th | |
Overdrive: Governor Wrench new special tool - R-11 and older | 18th-23rd | |
Overdrive: Governor Wrench, Econo-Drive short wrench - clears X-member | 18th; (19th-22nd) | |
Overdrive: Governor, Aero-Drive 19th Series switch cover supersedes 18th - use of 18th Series governors | 18th-19th | |
Overdrive: Governors, Econo-Drive improper operation - new switch cover | 18th-19th | |
Overdrive: Ignition Cut Out Econo-Drive, decelerating - relay adjustment | 18th-20th; (21st) | |
Overdrive: Indicator Light, Aero-Drive always on - headlamp resistance unit bent. grounded | 19th (exc. 1951) | |
Overdrive: Indicator Light, Aero-Drive on, standing - fuse check | 19th-20th | |
Overdrive: Installation, Economy-Drive field upgrade not cost-effective | 17th | |
Overdrive: Kickdown Switch, Econo-Drive shorting against starter - incorrectly mounted | 1803-3A-4-5-6-7-8 | |
Overdrive: Lockout Sleeve no reverse - sleeve operational checks, lubricant viscosity | 17th-20th | |
Overdrive: Lubrication, Econo-Drive changes in pilot bearing, thrust washer - hypoid oil permitted, unit identification | 1700-1-2-3-5 | |
Overdrive: Lubrication, Econo-Drive hypoid oil approved - new plugs/tag | 1700-1-2-3-5 | |
Overdrive: Lubrication, Transmission - Econo-Drive summer/winter - viscosity issues | 17th; (18th) | |
Overdrive: Lubrication, Transmission and... operating issues, cold - lubricant recommendations | 17th-20th | |
Overdrive: Operating the Econo-Drive proper engagement point - wear, noise benefits | 17th; (18th) | |
Overdrive: Parking in Gear Econo-Drive, on hills - use reverse gear only | 1700-1-2-3-5 | |
Overdrive: Parts, Econo-Drive parts reference - illustrated | 17th | |
Overdrive: Rear Bearings, Econo-Drive - Correction film supplement - race reference | 1700-1-2-3-5 | |
Overdrive: Rear Bearings, Econo-Drive production change, larger bearing - revised service procedure | 1700-1-2-3-5 | |
Overdrive: Rear Bearings, Economy-Drive - Renewing and Preloading service procedure | 1700-1-2-3-5 | |
Overdrive: Reverse Lock-Out Switch, Econo-Drive new plunger switch, relay, wiring, operation - partial or full installation | 1700-1-2 | |
Overdrive: Sluggish Engagement (or Clunks) insufficient friction, stationary gear balk ring/plate - R-9 | 18th-21st (22nd) | |
Overdrive: Snap-Ring Pliers, Econo-Drive new special tool - driving shaft locking rings | 17th; (18th-22nd) | |
Overdrive: Solenoid Installation, Econo-Drive solenoid failure - spacer inverted | 18th-20th; (21st) | |
Overdrive: Solenoid Repair contact replacement reiterated - solenoid shipment restricted | 18th-20th; (21st) | |
Overdrive: Solenoid Repair overdrive inoperative, burnt contacts - new parts kit, installation | 18th-20th; (21st) | |
Overdrive: Solenoid, Waterproofing road splash - seal housing/cover, terminals with Permatex | 17th-20th; (21st) | |
Overdrive: Transmission Case Cover compatible with OD units - requires lockout plunger | 17th | |
Overdrive: Transmission Jazz rattle/buzz, engine period - new type clutch thrust washer, driven plate | 1801 | |
Overdrive: Wiring Diagram schematic - circuit operation, troubleshooting | 18th-20th | |
Overdrive: Wiring Diagram, Aero-Drive new model information | 20th | |
Overheating Prestone anti-freeze - use of higher concentration | All Models | |
Packard and Delco Lovejoy Shock Absorber Fluid Recommendations | 6th thru 14th Series | |
Packard Oil Filter Kits PA-378689 | All 8cyl Engines 20th-23rd Series | |
Packard Quality Paint Material Information on paint | (not specified) | |
Paint: Blue Coral Treatment product information - finish restoration and protection | (all models) | |
Paint: Blue Coral, How to Use preparation - hand/machine application | (all models) | |
Paint: Delivery, Preparing Cars for improved paint/finish - washing/polishing | 17th | |
Paint: In-White Parts, Before Painting surface preparation - shipped without primer, but oiled | (not specified) | |
Paint: Lacquer Polish touch-up spots, improperly dried - proper hand polishing | (not specified) | |
Paint: Lacquer, Touch-Up product information - new, paint/solvent assortment | 19th | |
Paint: Lacquers, New lower viscosity - thinning proportions, by color | 120-138CD; 115C; 15th | |
Paint: Polishing, Body Packard Hard Gloss promotion | (all models) | |
Paint: Spots touch-up spots - proper polishing procedure reiterated | (not specified) | |
Paint: Sunburned, Why Cars Get loss of luster - polishing/waxing | (not specified) | |
Parts Book, Master revised format - new group classification system | 120C-138CD; 115C; 16th-18th; 19th (exc. 1951) | |
Parts List - Correction Master Part List clarification - hearse/ambulance/bus applications | 1701A-03A; 1801A-03A; 1901A-03A | |
Pedal Adjustment, Clutch high pedal pressure, Borg/Beck - assist spring adjustment | 18th | |
Pedal Adjustment, Clutch slippage, sticking in gear - free play | (all models) | |
Pedal Clearance, Brake dragging brakes, by-pass port blocked - pedal clearance adjustment | 120-138CD; 115C; 15th-16th | |
Piston - Standard Sizes and Adjustments Changes skirt clearance - range reduced | 2000-01-10-11-20-21-30 | |
Piston and Rings, Replacement latest type used for earlier models - check replacement chart for rings only | 9th-14th; 120-138CD; 115C; 15th-20th | |
Piston Oversize Diameters revised specification, skirt clearance reduced - size reference | ?1st-14th; 120-138CD; 115C; 15th-16th | |
Piston Oversize Diameters revised specification, variation reduced - size reference | ?1st-14th; 120-138CD; 115C; 15th-17th | |
Piston Pin Bushings two-piece, split-type - oil groove, burnishing procedure | 120-138CD; 115C; 1600-1-1A-1D-2-3-4-5; 1700-1-1A-2-3-3A-5; 18th-20th | |
Piston Ring Sets Perfect Circle - ordering | (all models) | |
Piston Rings clarification of pistons/rings used in production - aluminum/cast-iron, specifications | 20th | |
Piston Rings Perfect Circle 200 top ring - identification, proper installation | 18th | |
Piston Rings and Expanders ample supply for spring season repairs | (not specified) | |
Piston Rings, Carbonized oil consumption, low speed, cold weather - oil changes, cleaning procedure | (all models) | |
Piston Rings, Selling and Installing Perfect Circle ring groove combinations - use of selection chart | 9th-14th; 120-138CD; 115C; 15th-20th | |
Pistons cast iron to replace aluminum in production - specifications correction | 20th | |
Pistons and Piston Rings - Super Eight new Thermo-strut pistons, special-alloy rings - retrofit, precautions | 1501-2-3; 1603-4-5; 1703-5 | |
Pistons, Cast Iron engine suffix C or higher - skirt clearance, installation | 20th | |
Pistons, Oversize Marking on formerly paint, now stamped - prior chart obsolete | 120C-138CD; 115C; 15th | |
Plate Aligning and Riveting Fixtures, Clutch new tools - proper use | (not specified) | |
Plate Aligning Fixture Expansion Arbor, Clutch new special tool - updates existing arbor | 1703 | |
Plates, Clutch higher friction lag driven plate for Aero-Drive - identification | 1800-1; 1900-1 | |
Power, L-Head vs. Valve-In-Head higher torque/HP - detonation | (all models) | |
Pressure Spring, Clutch part reference - identification | 7th-20th | |
Radiator (Grille) Covers product information - quick warm up, efficient motor performance | 120-138CD; 115C; 1800-1-2-3-4-5; 1900-1 | |
Radiator - Packard Rust Preventive Information | (not specified) | |
Radiator Caps, Pressure for use with special pressure radiators - function, checks | 1800-1 (w/ AC); 1803-3A-4-5-6-7-8 | |
Radiator Drain Cock location change - more accessible | 1600-1-2 | |
Radiator Insect Screens product information - protection/appearance item | 18th | |
Radiator Shutter Thermostats low-temperature application expanded - revised specifications | 16th | |
Radiator Shutter Thermostats lower temperature for 1600-1, alcohol antifreeze - part reference | 16th | |
Radiator Shutter Thermostats specifications, identification - part reference | 6th-14th; 120CD-138CD; 15th-16th | |
Radiator Shutter Whistle partly open - quicker thermostat, new blade assemblies | 1500-1-2-6-7-8 | |
Radiator Whistle road speed - not shutters, insert screen | 1500-1-2-6-7-8 | |
Radiator Winterfront - Installation Improvement field modification of attaching bars - more secure | 18th | |
Radiator Winterfront Installation product information - proper procedure | (not specified) | |
Radiators and Cooling Systems, Rustproofing expired cooling solutions - cleaning/flushing, anti-freeze | (all models) | |
Radio - Careful Adjusting, Installing synchronizing with antenna - instrument panel squeaks | 19th? | |
Radio Condenser, Installation of short wave tuning - Auto-Lite vs. Delco regulators | (not specified) | |
Radio Frequency Changes automatic radios - readjusting push buttons | 17th-19th | |
Radio Static hum, motor noise - static discharge, clean fan belt | (all models) | |
Radio Tube Removal - Accessory Notes pry through holes in housing | 19th | |
Radio Warranty Service Philco - third-party service procedure | (not specified) | |
Radio, Improved De Luxe new design audio circuit - bass compensation | (not specified) | |
Radios, Service Kit for fast-moving parts - dealer service | (all models) | |
Reading Light and Starter Switch Wrench, new special tools - combination | 1601-3-8; 1701-3-8 | |
Reading Light and Starter Switch Wrench, Instrument Board new special tools - required | 1600-1-3 | |
Reading Light Switch Wrench, Instrument Board new special tool - special nut | 1800 | |
Rear Axle - Standard Sizes and Adjustments Changes capacity reduced | 2021 | |
Rear Axle Capacity fluid - changes | 120C-138CD; 115C; 1600-1-1A-1D-2; 1700-1-1A-2-3-5; 18th | |
Rear Axle Lubricant production fill, break-in properties | (not specified) | |
Rear Compartment Lid Lock Handle Assembly, Lamp (License) superseded - now includes small detail parts | 1800-1-3 | |
Rear End Pitch front end stiff/bottoming ling pin lubrication, rebound clearance | 1600-1 | |
Rear Fender Assembly - Correction Master Part List omission - additional applications | 1800-1-3-4-6-7 | |
Rear Fender Gasoline Filler Lid Assembly back in stock | 19th (exc. 1951) | |
Rear Fender Gravel Shields parts back in stock - LH | 1900-1-1A-3-3A-4-5-6-7-8 | |
Rear Fenders back in stock | 19th (1432-42-52-62-72-76-77-78-79-92-94-95-96-97-98) | |
Rear Spring (Squeaks) covers eliminated - new Silenite inserts, brass oil cups, rebound clips | 1600-1 | |
Rear Spring - Parts Book Correction incorrectly listed as front | 1903 | |
Rear Spring - Parts List Correction incorrect part number | 1800-1 | |
Rear Spring Inserts lubrication, rubber/Silenite decomposition - repacking lead type | 1600-1-2; 1702-3-3A; 18th-20th; (21st-22nd) | |
Rear Spring Inserts soft ride, excessive strike-through - rubber/Silenite insert decomposition, replacement | 1600-1-2; 1702-3-3A; 18th-20th; (21st-22nd) | |
Rear Spring No. 367726 incorrectly listed as front | 1904-07 | |
Rear Springs - Save the Grease rubber/Silenite deterioration | 1600-1-2; 1702-3-3A; 18th-22nd | |
Rear Springs new insert type springs, shock valving changed - reference chart | 1600-1-2 | |
Rear Springs new type separators, insulators and covers - do not lubricate | 1600-1-2 | |
Rear Springs, Dont Lubricate soft ride, clutch chatter - rubber/Silenite decomposition/replacement, repacking lead type | 1600-1-2; 1702-3-3A; 18th-20th; (21st-22nd) | |
Rear Springs, Squeaks - Insert Type worn/oxidized inserts - inspection, reconditioning, replacement | 1600-1-2; 1702-3-3A; 18th-22nd | |
Rear Wheel Hub Puller - Special Tools new required tools | 1800 | |
Rear Window Curtains product information, roll-up type - privacy/protection | 16th-18th (Sedans) | |
Refrigerant (Methyl Chloride) wartime shortage, Freon substitute - precautions, warning plates | 18th-20th | |
Relay Lever Pins, Clutch working loose, booster mechanism - new design pin | 1703-3A-5; 1803-3A-4-5-6-7-8; 1800-1-1A (w/ Borg&Beck) | |
Relay Lever, Clutch (Electromatic) control valve squeak, sticky throwout - relay lever bearing adjustment | 1900-1 | |
Relay Lever, Clutch - Extra Lubrication Point Super Eight or Borg-Beck equipment - identification | 18th | |
Relay Lever, Clutch - Super Eight centralizing springs - additional washers | 1703-3A-5; 1803-3A-4-5-6-7-8; 1903-3A-4-5-6-7-8 | |
Ride friction lag - neutralizing springs, shock absorber alignment, lead spring buttons | 18th | |
Ride harsh, excessive fiction lag - shock alignment, neutralizing suspension | 1700-1-2-3-5 | |
Rides, 17th Series softer ride - new compression/rebound valves, front/rear | 1703 | |
Riviera Models, Special special paint/ trim colors - part reference | 1700 (1282); 1701 (1292); 1703 (1272) | |
Roar, Engine highway speeds, air cleaner - new brace grommet, use of Super Eight heater tube support | 1800 | |
Roughness, Engine engine snubber adjustment - neutralizing | 18th (exc. Econo-Drive) | |
Rubber Bumpers - Rear brake junction contacting floor - new rebound, reduced travel | 1600-1-2 | |
Rubber Floor Mats front floor - back in stock | 1700-01; 1800-01; 1900 | |
Rubber Mats front and rear floor covering - available | 120-B-C; 115C; 1600-1; 1700-1-2; 1800-1; 1900; 1951; 2000-01; 20th? (non-Clipper); 2100-01-03-11 | |
Rubber Mats front floor covering - back in stock | 120-B; 115C; 1600-1; 1700-1-2; 1800-1; 1951; 2000-01; 20th? (non-Clipper); 2100-01-03-11 | |
Running Board Antenna ground required - straps furnished | (not specified) | |
Rust Preventative amount, period - directions | (all models) | |
Rust, Preventing formation, cooling system damage - rust inhibiting agent | (all models) | |
Screw Driver, Offset (Phillips) new special tool - front door hinge | 16th | |
Screwdrivers (Phillips) new special tool - new special screw/head | 16th | |
Seat Adjustment, Front adjuster wood shims - use of Six steering post bracket | 1700-1-2-3-5 | |
Seat and Back Position Change, Front more upright position - installation of wood wedges | 1600-1-2 | |
Seat Covers, San-Tex product information - benefits | (all models) | |
Seat Covers Information | (not specified) | |
Seat Cushion Location Delivery Inspection | (Not Specified) | |
Seat Cushion Riding Height requests for lower - adjuster rail modification | 18th | |
Seat Position raise/lower/angle modifications - steering column bracket interchange | (not specified) | |
Service on...Vehicles Delivered by Henney Motor Company warranty policy | 18th | |
Servicing the Transmission overhaul procedure | 17th-21st | |
Servicing...(Spring Operation) air filters - refrigerant checks | 18th-19th; (20th) | |
Servicing...Units for Spring Operation refrigerant/oil checks | 18th-20th | |
Shifter Lever Interference interference with rear motor support - rework existing stock, superseded part | 1703-3A-5; 1803-3A-4-5-6-7-8; 1903-3A-4-5-6-7-8; 2003-04-05-06-07-08-23-55; 2103-06-26 | |
Shipping Weights Corrections, Complete Car new model information - dimensions | 120C; 115C; 15th | |
Shipping Weights, Complete Car new model information - dimensions | 120C; 115C; 15th | |
Shock Absorber - Tool Suggestions Houde shock valve wrench | 1601-1A-1D-2 | |
Shock Absorber Assembly - Parts Book Correction incorrect application - Senior cars, RH-LH | (not specified) | |
Shock Absorber Camber Pilot Wrench new special tools - required | 1507; 1607 | |
Shock Absorber Fluid Delco-Lovejoy vs. Houdaille - part reference | (not specified) | |
Shock Absorber Fluid Gun new special tool - dual-action | (not specified) | |
Shock Absorber Noise squeak/grunt, binding/friction-lag - check alignment, Neetsfoot oil additive | 1800-1 | |
Shock Absorber Noise, Direct-Acting Monroe vs. Delco - checks, corrections | 18th | |
Shock Absorber Oil cold weather - alcohol additive, softer ride | 1601 | |
Shock Absorber Valve Wrench new special tools - required | 1601 | |
Shock Absorber Valves conventional and static types - different nuts required | 1600-3-4-5; 1700-1-2-3-5 | |
Shock Absorber, (Lateral) Fifth 17th Series feature - installation | 16th | |
Shock Absorber, Servicing ride complaints - front modification, rear overhaul/parts | 1801-3-6; 19th (exc. 1951) | |
Shock Absorbers (Houdaille), Springs and fluid type changed, new firmer valve - rear rebound bumper clearance, new longer design | 1600-1 | |
Shock Absorbers Houdaille - inspection, service | 1601-2 | |
Shock Absorbers softer ride - new compression/rebound valves, front/rear | 1700-1 | |
Shock Absorbers Chart, Spring and part number reference | 120C-138CD; 115C; 15th | |
Shock Absorbers Chart, Spring and reduced load springs, shock valving - high/low equipment | 18th | |
Shock Absorbers, Aligning Front changed position, LH-RH - modifications, identification | 1700-1-2-3-5 | |
Shock Absorbers, Changing Fluid in Houdaille new fluid change procedure - eliminates unit replacement | 1600 | |
Shock Absorbers, Disassembling Direct-Acting wrench slots tearing out - correction, prevention | 18th | |
Shock Absorbers, Houdaille final recommendations, loss of resistance - fluid, thermostatic valves | 1600 | |
Shock Absorbers, Houdaille new design, superseding part- new adjustable type | 1600-1-1A-2 | |
Shock Absorbers, Parts for Direct Acting Rear Monroe, Delco - supplier cross-reference | 1801-3-6; 19th (exc. 1951) | |
Shock Absorbers, Rear fluid capacity - proper disassembly/refilling | 19th (exc. 1951) | |
Shock Absorbers, Spring and part number reference - leaf insert location/type | 19th (exc. 1951) | |
Shock Absorbers, Spring and part number reference - leaf insert location/type | 20th | |
Shock Absorbers, Springs and (Houdaille) fluid type changed, new firmer valve - rear rebound bumper clearance, new longer design | 1600-1 | |
Shock Absorbers: Firm Ride recommended valve combinations reference table | 120C; 1500-2-8 | |
Shock Absorbers: Special Tool Correction piston rod thimbles oversize - check dimension, return/rework | 18th | |
Shock Absorbers: Special Tools new required tools - domestic/export sets | 18th | |
Shop Manual Change - Alignment checking toe-in | 120-138CD; 115C; 15th-18th; 19th (exc. 1951) | |
Shop Manual Correction, 1937 tappet settings - valve timing, Super Eight | 1500-1-2 | |
Shop Manual Corrections (1938-1939) clutch relay lever lubrication - Super Eight, 1939 only | 1703-3A-5 | |
Shop Manual Corrections (1938-1939) cooling system capacity | 1601-1A-2; 1701-1A-2 | |
Shop Manual Corrections (1938-1939) crankcase oil capacity | 1600; 1700 | |
Shop Manual Corrections (1938-1939) starter motor oilers - Super Eight | 1603-4-5; 1703-3A-5 | |
Shop Manual Corrections (1938-1939) transmission oil capacity - engine tappet settings | 1603-4-5; 1703-3A-5 | |
Shop Manual Corrections (1938-1939) transmission oil capacity | 1603-4-5; 1703-3A-5 | |
Shop Manual Corrections (1938-1939) valve tappet settings - Super Eight | 1603-4-5; 1703-3A-5 | |
Shop Manual Corrections crankcase, cooling system, transmission capacities | 16th-17th | |
Sludge, Crankcase driving speed reductions, condensation, bearing trouble - operating temperatures, oil changes | (all models) | |
Sludge, Engine cleaning oil pan/screen - engine flushing | (all models) | |
Sound Deadener and Water Sealer new 3M product - application | All Models | |
Spare Tire Rattle trunk compartment - fabricate shim | 18th | |
Spark Knock light governor spring - part number change | 1801 | |
Spark Knock new, modified spark advance - light governor spring for service, identification | 1801 | |
Spark Knock Again lower octane, carbon deposits - spark advance, additional head gasket | (all models) | |
Spark Plug Plug Identification and Model Application Chart | (see chart) | |
Spark Plug Cleaning use of sand blast cleaner - proper gap | (all models) | |
Spark Plug Covers hard/no starting, dirt/moisture - new covers prevent shorts | 16th-17th | |
Spark Plug Covers hard/no starting, dirty spark plug porcelains - new bakelite covers | 16th-17th | |
Spark Plug Gap, Magnifying and Adjusting Tool new special tool - for new style plugs | (all models) | |
Spark Plug Part Numbers AC, Champion, Auto-Lite - cross-reference | 1st-8th; 10th-14th; 120-138CD; 115C; 15th-21st | |
Spark Plug Terminal Insulators Accessory Spark Plug Boots | Models with 10mm plugs | |
Spark Plug Terminal Nuts brass, wartime shortage - plugs shipped less nuts | (not specified) | |
Spark Plugs, Hot driving speed reductions, fouling - new higher heat range | 120C-138CD; 115C; 16th-20th | |
Spark Plugs, Resistor Type cross-referenced - proper gap | 120C-138CD; 115C; 16th-23rd | |
Spark Plugs, Shorted dirt, moisture - clean porcelain | (all models) | |
Spark Plugs, The Why and How of 10mm engine speed/compression, temperature stabilization - service precautions | 120C, 115C; 15th | |
Spark Plugs, Wiping Off oil/dust, moisture - shorting over porcelain | (all models) | |
Speedometer and Pinion Shaft, Transmission standard and overdrive - part reference | 16th-18th | |
Speedometer Complaints irregular operation - cable lubrication, pinion selection | (all models) | |
Speedometer Complaints noise, reading error - checks, lubrication | (all models) | |
Speedometer Mileage low trip reading - rest cable kinks, knob not pulled out | 1903-3A-4-5-6-7-8 | |
Speedometer Pinion and Shaft part reference - corrected | 19th-20th | |
Speedometer Pinion and Shaft part reference | 19th-20th | |
Speedometer Pinions, Gears and Bearings part reference | 120-138CD; 115C; 15th | |
Speedometer Pinions, Gears and Bearings part reference | 16th | |
Spring and Shock Absorbers - Correction taxicab front spring - part number | 1900 | |
Spring and Shock Absorbers part number reference - leaf insert location/type | 19th (exc. 1951) | |
Spring and Shock Absorbers part number reference - leaf insert location/type | 20th | |
Spring and Shock Absorbers Chart part number reference | 120C-138CD; 115C; 15th | |
Spring and Shock Absorbers Chart reduced load springs, shock valving - high/low equipment | 18th | |
Spring Remover and Replacer Wrench, Brake new special tool - Bendix type | 120-138CD; 115C; 15th-23rd | |
Springs and Shock Absorbers (Houdaille) fluid type changed, new firmer valve - rear rebound bumper clearance, new longer design | 1600-1 | |
Springs, Airport Bus front no longer available - return and recondition | 1903 | |
Springs, Safe-T-Flex riding height reference - spacers available | 120-138CD; 115C; 15th-17th | |
Squeaks, Brake coming to full stop - brake drum damper spring, expanded applications | 12th-14th; 120-120C; 115C; 15th | |
Stabilizers front/rear roll control bars, tubular lateral shock absorbers - grommet compression, dimensions | 17th-20th; 21st | |
Standard Size Correction - Chassis Lubrication starter motor oilers, clutch lever fitting - transmission fluid types | 17th | |
Starter Motor (Battery) Cable chafing, shorts - rerouted, additional clip | 1700-1-2-3-5 | |
Starter Motor - Standard Sizes and Adjustments Changes oilers reduced | 2020-21 | |
Starter Motor Bendix Drive - Anti-Kick Out Type false starts, premature disengagement - new type, operation | 20th-25th | |
Starter Motor, Replacement superseded part - external ground wire eliminated | 20th | |
Starter Switch, Car (Carburetor Switch) operation, failure - checks, adjustments | 1951; 20th; (21st-26th) | |
Starter Switch, Generator Connection to new safety feature, cut-off - new solenoid switch, retrofit | 1951; 20th | |
Starting - Cold Weather Proper Procedure | (Not Specified) | |
Starting Circuit engine not cranking - circuit checks | 1951; 20th | |
Starting Circuit generator-grounded, safety-type - return to starter ground | 20th | |
Starting Circuit starter solenoid ground relocation, carburetor switch operation - reiterated | 20th; (21st-26th) | |
Starting the Motor Without Getting into the Car, Handy Way to remote starter switch - fabrication and use | (not specified) | |
Static Electricity shocks, radio interference - tire tube powder kit | (all models) | |
Station Wagon Warranty Hercules Body Company - processing claims | 18th (1383-93); 19th (1463-73-83-93) | |
Steering and Strike Through Correction lack of control - shim shock absorber valve blow-off spring | 18th | |
Steering Center Crank Lubrication overlooked Zerk fitting | 120-138CD; 115C; 15th-18th; 19th (exc. 1951); ?2001A-3A-4-5-7-8-20-21-23-30-55 | |
Steering Column Alignment stiff/binding, bearing snap - checks/adjustments | (not specified) | |
Steering Column Brackets, Correction increased head room - part number correction, by chassis | 1600-1-2 | |
Steering Crank Centering Gauge new special tools - required | 1600-1 | |
Steering Crank Gauge tool modification required | 17th | |
Steering Crank Pin new assembly, reduced wear - supersedes prior detail parts, proper lubrication | 1700-1-2-3-5 | |
Steering Cross Tube adjusting clamp bolt striking torque arm - orient vertically | 1507-8 | |
Steering Cross Tube Dust Washer replaced by conical spring | 120C-138CD; 115C; 16th-19th; (20th) | |
Steering Cross Tubes - Parts List Correction detail parts no longer serviced - superseded by assemblies | 18th-19th | |
Steering Gear Case Reconditioning Tools new bushing tools - proper use | 120-138CD; 115C. 1600 | |
Steering Gear Cross Shaft Adjusting Locknut Wrench new special tool - play adjustment | 1500-6-7-8 | |
Steering Gear Cross Shaft Adjusting Wrench screw head enlarged - rework tool | 1500-6-7-8 | |
Steering Gears overtightened frame bolts - crushed rubber insulator | 19th | |
Steering Kick severe/sensitive conditions - export type knuckle thrust bearings | 1700-1-2-3-5 | |
Steering Kick use of export type bearings - application expanded | 120-138CD; 115C; 1500-1-2; 1600-1-1A-1D-2; 1700-1-1A-2-3-3A-5 | |
Steering Knuckle Bearings return to ball thrust bearings, bronze king pin bushings - as in 18th | 19th | |
Steering Knuckle Pin Burnisher new special tools - required | 1603 | |
Steering Knuckle Spacer Sleeve new special tool - old and new style bushings | 1600-1; 1700-1-3 | |
Steering Rattle gear shift anti-rattle screws - add flat washer | 19th (exc. 1951) | |
Steering Stabilizers, Lubrication of plunger, piston gland packing, ball joints - interval | (not specified) | |
Steering Wheel Fight linkage adjustment, bronze bushings, blow-off valves reiterated- new steering lever with rubber bushings | 18th | |
Steering Wheel Fight steering linkage backlash - steering gear adjustments, steering crank indexing | 1801 | |
Steering Wheel Puller new special tool | 1700-1-3 | |
Steering Wheel, De Luxe part number clarification - Handishift applications | 17th | |
Steering Wheel, Raising - Correction application clarification - additional kit | 19th (exc. 1951) | |
Steering Wheel, Raising column shift, requires additional parts - new kit | 18th | |
Steering Wheel, Raising extended from 18th Series - equipment kit | 19th (exc. 1951) | |
Steering Wheels, De Luxe - Special...Notice Accessory Price List corrections - motor numbers | 1700 | |
Sticking in Low Gear loose detent block, forks, levers, rods - insufficient clutch clearance | 17th-20th | |
Stone Shields now standard - available for earlier cars | 19th (exc. 1951) | |
Stud Remover and Driver new special tool - cylinder head studs | (all models) | |
Sun Visor Glare Shields product information - clamp-on | (not specified) | |
Sun Visors support rod available for service | 18th (1372-79-82-89-92-99); 19th (1477-79-89-97-99) | |
Support Arm Bearing, Front - Lubrication Caution 18th Series changes - excessive pressure | 120-138CD; 115C; 15th-18th | |
Support Arm Inner Pin Bushing Aligner, Wheel new special tools - required | 1600-1 | |
Support Arm Inner Pin Bushing Removing and Replacing Tool - Sleeve new special tool - front wheel toe-in, addition | 120-138CD; 115C; 15th | |
Support Arm Inner Pin Bushing, Wheel - Special Tools new required tools - aligner, installer | 18th | |
Support Arm Pin Bearing superseded part - late design, no oiler | 120-138CD; 115C; 15th-20th | |
Support Bushing Bolt, Removing Wheel - Correction clamp supplier error | 120-138CD; 115C; 15th-18th; 19th (exc. 1951); 2001A-3A-4-5-7-8-20-21-23-30-55 | |
Support Bushing Bolt, Removing Wheel Safe-T-Flex suspension - tool fabrication, use | 120-138CD; 115C; 15th-18th; 19th (exc. 1951); 2001A-3A-4-5-7-8-20-21-23-30-55 | |
Support Bushing Repair Kit, Front Wheel new service parts | 120-138CD; 115C; 1600-1-2; 1700-1-1A-2-3-5; 18th; 19th (exc. 1951); 2001A-3A-4-5-7-8-20-21-23 | |
Support Outer Bearing, Wheel - Special Tools new required tools - aligner, driver | 18th | |
Support Plates, Front Brake superseded parts - requires modification for wheel cylinder | 1500-1-2; 1603-4-5; 1701A-3A; 1801A-3A; 1901A-3A; 2001A-3A; 2213-26 | |
Tappet Hole Reamer, Valve new special tools - required | 1600-3 | |
Tappets, Hydraulic Super Eight, oil supply - special oil filter, inspection. cleaning | 1803-3A-4-5-6-7-8 | |
Tappets, Noisy (Super Eight) - see also: Hydraulic Tappets Oil Filter Oil Pressure Oil Pump | -- | -- |
Tappets, Noisy - Super Eight low oil pressure - close/redrill filter elbow | 1803-3A-4-5-6-7-8; 1903-3A-4-5-6-7-8 | |
Tappets, Noisy - Super Eight low oil pressure at idle - 20th Series piping, retrofit | 1803-3A-4-5-6-7-8; 1903-3A-4-5-6-7-8 | |
Tappets, Valve - Special Tools new required tools - hole reamer, adjusting wrench | 18th | |
Tappets, Valve excessive replacement - service parts reiterated, superseded assembly | 1803-3A-4-5-6-7-8 | |
Tappets, Valve Six/Eight - self-locking screw - Super Eight plunger/tappet replacement | 18th | |
Tire in Fender Wells, Inflating spare wheel carrier revised - eliminates tire cover removal | 18th | |
Tire Information, Correct and Uniform tire wear/life - inflation pressures, driving habits | (all models) | |
Tire Life wartime shortage - pressure increase | (all models) | |
Tire Manufacturers Standard Warranty special insert - claims handling | (not specified) | |
Tire Noise - Correct Diagnosis detection - elimination | (all models) | |
Tire Pressure, New Car high for delivery - inflate to recommended | 18th | |
Tire Pressures, Higher increased tire life - harsher ride, rattles | (all models) | |
Tire Thump diagnosis | (all models) | |
Tire Wear, Causes and Correction of air pressure, wheel alignment, excessive suspension motion | (all models) | |
Tire Wear, Equalizing heel-and-toe wear, noise - cross-switching | (all models) | |
Tire Wear, Equalizing saw-tooth/heel-toe front wear - high-speed driving, cross-switching tires | (all models) | |
Tire, Removal of...from Side Carrier five tire limit - supporting empty cover | 18th-20th | |
Tires Again cross switching, higher pressures - reiterated | (all models) | |
Tires, Care And Storage of White Sidewall removal of protective coating reiterated | (all models) | |
Tires, Cleaning White Wall non-yellowing tire cleaner available | (all models) | |
Tires, Cross Switching tire rotation pattern - increased tread life | (all models) | |
Tires, Cross-Switching irregular tread wear - tire rotation, benefits | (all models) | |
Tires, Effect of...on Gasoline Consumption pressure, tread wear - ride, squeaks/rattles | (all models) | |
Tires, Rotate...Around Car uneven wear, rough ride - proper cross-switching procedure | (all models) | |
Tires, Synthetic synthetic rubber, tubes - characteristics, identification | (all models) | |
Tires, Synthetic vs. Natural Rubber complaints, characteristics - proper mounting/inflation | (all models) | |
Tires, White Sidewall return to production - removal of new protective coating, proper storage | (all models) | |
Tool Bag Equipments limited supply, used car opportunity - kit details | 1900-1-1A; (all models) | |
Tool Bag Hold Down Strap fender-well spares - trunk mounting hardware | 18th and Prior? | |
Tool Kits Available export equipment, domestic use - container and additional tools | (not specified) | |
Tools - Keeping Them Quiet five-wheel equipment storage - six-wheel equipment under review | 19th | |
Torque Arm front suspension squeak/rattle - bracket interference, grind/straighten for clearance | 1800-1-3-6 | |
Touch-Up Lacquer product information - new, paint/solvent assortment | 19th | |
Transmission - Econo-Drive Lubrication summer/winter - viscosity issues, draining/filling | 17th; (18th) | |
Transmission and Overdrive Lubrication overdrive issues, cold - lubricant recommendations | 17th-20th | |
Transmission Hoist Special Tool ST-844 | All Models | |
Transmission Lubricant seasonal oils - viscosity issues | (all models) | |
Transmission Lubricants warm weather, bearing noise - new Kendall 400 oil | (not specified) | |
Transmission Service Units part number reference - supersedes parts book | 120-138CD; 115C; 1600-1-1A-1D-2; 1700-1-1A-2-3-3A-5; 18th; 1900-1-1A-3-3A-4-5-6-7-8 | |
Transmissions noisy, coasting/light throttle - heavier oil, new type clutch driven plate | 1600 | |
Transmissions parts shortage - substitute assemblies, speedometer cable | 1800-3-3A-4-5-6-7-8; 1903-3A-4-5-6-7-8; 2003-06; ?2004-05-07-08?; 2103-06 | |
Transmissions superseded - speedometer cable serviced separately | 20th? | |
Transmissions and Parts Now Available 1st/2nd speed driving shaft - back in stock | 1951; 2000-01-03-06-10-11; 21st | |
Transmissions and Parts Now Available assemblies, shafts, cluster gear - back in stock | 1951; 2000-01-03-06-10-11; 2100-01-11-30 | |
Transmissions and Parts Now Available clutch (input) shaft - back in stock | 1700-1-1A-2; 1800-1-1A; 1900-1-1A; 1951; 2000-01-03-06-10-11; 2100-01-11-30 | |
Transmissions and Parts Now Available countershaft cluster gear - back in stock | 120-138CD; 115C; 1600-1-1A-1D-2 | |
Transmissions, Service shipped dry, inspect syncromesh balls/springs - new special tool | (not specified) | |
Trunk Lid Handle lid coming open - shim toggle plate | 18th | |
Trunk Rack Installation proper procedure - replacement of tail/license lamps, 1600-1 | 16th | |
Trunk Racks (Installation) tail/license lamps replacement no longer required for sedans - specials lamps available separately | 1600-1 | |
Trunnion Bearing Assembly, Universal Joint supplier part superseded - install in pairs | 120-138CD; 115C; 17th-18th | |
Tube Failures, Static Electricity and sparks/ozone, conditions - static elimination powder available | (all models) | |
Tube Failures, Static Electricity and sparks/ozone, conditions - static elimination powder available | (all models) | |
Tubes, How to Install Synthetic recommended mounting method | (all models) | |
Tubes, Lifeguard - Twelve matched to tires, balancing - use in other cars | 1707-8 | |
Underbody Protective Coating product information - rust/corrosion prevention, supplier | (all models) | |
Universal Joint Kit spider and trunnion repair parts - packaged in sets | (not specified) | |
Universal Joint Lubrication, Front ball-and-trunnion type - identification, interval | 1900; 2000 | |
Upholstery Protection new vehicle storage, moth spray/moth crystals - germination reminder | (all models) | |
Valve Lifter Mechanism - Super Eight noisy lifters - clogged filter, lifter test | 1803-3A-4-5-6-7-8 | |
Valve Lifter Mechanism - Super Eight supplied by oil filter - use OE filter only | 1803-3A-4-5-6-7-8 | |
Valve Seats, Checking run-out, uneven wear - use of dial indicator | (all models) | |
Valve Spring Load reduced by cutting seats - shimming, precautions | (not specified) | |
Valve Springs, Camshaft and cast-iron/steel, engine suffix identification - corresponding oil pump gear | 1600-1-2 | |
Valve Springs, Weak sticking valves - shimming | (not specified) | |
Valve Timing specifications reference | 900-1-2-3-4; 10th-14th (exc. Twelves); 120-138CD; 115C; 15th-19th; 2000-1-3-3A-4-5-6-7-8-20-21-23 | |
Valve Tools new required tools - hand grinder, suction cup | 18th | |
Valve Wrench - Tool Suggestion improvement - stops slipping | (not specified) | |
Valves and Car Storage, Sticky running motors, internal rust - cylinder oiling, battery removal/charging | (all models) | |
Valves, Rusted Cylinders and moving stored vehicles - preparations for starting | (all models) | |
Valves, Sticking carbon, gum, rust, mechanical causes/remedies | (all models) | |
Valves, Sticking production change, field retrofit - valve cut-off/counterbore, valve covers with oil baffles | 1600-1 | |
Valves, Sticking production change, field retrofit reiterated - new counterboring tool | 1600-1 | |
Valves, Sticking vehicles in storage - precautions reiterated | (all models) | |
Valves, Sticky cold starts/stops, rust in guides - new corrosion-resistant material | (all models) | |
Valves, Sticky exhaust valves, rust - proper storage | (all models) | |
Valves, Sticky valve guide rust - new filler, cap and duct increase crankcase ventilation, check for gum/varnish/carbon | 19th | |
Valves, Sticky valves/guides - valve spring tension | (all models) | |
Vapor Lock operating temp, seasonal gasoline grade, pump pressure - checks, remedies | (all models) | |
Vapor Lock warm weather - reiterated | (all models) | |
Vehicle Reference, Packard model, body, motor numbers - 1931-1948 | 8th-14th; 120-138CD; 115C; 15th-22nd | |
Vehicle Stamp Set new special tool - dealer/delivery info | 16th | |
Vibration Damper Assembly Kit superseded - modifications | 1900-1-1A; 1951; 2000-01-11; 2100-01-11-30; 2200-11-02-20- 22-33-40; 2302-22-33 | |
Vibration Damper Wrench new special tools - required | 120-120B; 115C 1600-1 | |
Voltage Regulator - Dont Forget It blackened breaker points, burned out bulbs - excessive voltage, reiterated | 1800 | |
Voltage Regulator Adjusting Gauges and Feelers new special tool package - all types | (all models) | |
Warm Weather Service engine/cooling system - inspection/maintenance | (all models) | |
Water Distributing Tube (Manifold) persistent overheating - function, inspection, corrosion | 120-138CD; 115C; 1600-1-1A-2; 1700-1-1A-2; 18th-20th; (21st-54th) | |
Water Pump Body, Refacing impeller relationship, new type seals - rebuilding procedure | 1600-1-1A-2; 1700-1-1A-2; 18th-21st | |
Water Pump Leaks seal thrust washer vs. repair kit - housing refacing tool | 16th-20th | |
Water Pump Leaks thrust washer blisters - hot/cold water refilling | 16th-20th | |
Water Pump Seal, New new seal assembly, thrust washer - proper installation | 16th-20th | |
Water Pump Seat Refacer new special tool - overhaul, smooth/true cutting | 1600-1-1A-2; 1700-1-1A-2; 18th | |
Water Pump Shaft bore wear - set screw required | 1600-1-2 | |
Water Pump Shaft superseded to 17th Series - additional modifications | 1600-1-2 | |
Water Temperature Gauge - Caution When Removing shorts, dial damage - disconnect battery lead | 15th | |
Weather Conditioned Cars new model information - separate parts list | 18th | |
Weatherstrips, Door - Cold Weather Precaution sponge rubber door seals, frozen/torn - drying, warming | 120C; 115C; 15th | |
Weatherstrips, Door air/dust leaks, panel variations - rubber shim material available | (not specified) | |
Wheel Blocks, Safety Angle Sells New product information - jacking safety | (all models) | |
Wheel Carrier Clamp Bolts - Hardened worn threads - superseded part, identification326442 | 16th-18th | |
Wheel Discs, Chrome - New Accessories set of five | 1800 | |
Wheel Hub Cap Puller new special tool - front hub grease cap | 1800 | |
Wheel Locks product information - stud locks, hub shields | (not specified) | |
Wheel Locks, Lubrication of cap installation interference - Lubriplate | (not specified) | |
Wheels design difference - not interchangeable | 120-138CD; 115C; 1600-1-2 | |
Window Cylinder Boots, Hydraulic - Automatic Windows new service part - proper installation | 1906-7-8; 2006 (1529); 2007-8 | |
Window Cylinders, Hydraulic rust/corrosion - grooved collar added | 1906-7-8; 2006 (1529); 2007-8 | |
Window Lifter Valve (Seat) Tool special tool, limited availability - pump housing | 1906-7-8; 2006 (1529); 2007-8 | |
Window Regulator - Hydraulic Wiring Diagram new model information | 2007-8 | |
Window Regulators, Hydro-Electric components, operations - service instructions | 1906-7-8; (2006 (1529)); (2007-8) | |
Window System, Pumps in Hydraulic window closing, low pressure - dirt, corrosion | 1906-7-8; 2006 (1529); 2007-8 | |
Windows, Adjusting Ventilating regulator backlash - procedure | 1600-1-1D-2 | |
Windshield Washer new accessory - cleaning benefits | 20th? | |
Windshield Washer Solvent All-Season Mixture anti-freeze and cleaning benefits - seasonal blending | (all models) | |
Windshield Wiper Adjustment cleaning arc - reindexing blades | 1800-1-3-6 | |
Windshield Wipers increasing cleaning arc - longer blades, linkage modifications | 1800-1-3-6 | |
Windshield Wipers insufficient cleaning - blade contamination, arm tension adjustment | (not specified) | |
Windshield Wipers, Electric failure to start/stop, blown fuse - dynamic breaker, obtain form Stewart-Warner | 1800-1 | |
Winter Driving, Preparing Cars for cooling system checks and maintenance | (all models) | |
Winter Driving, Preparing Cars for fuel system checks and maintenance | (all models) | |
Winter Motor Temperatures slower driving, shorter trips, fuel economy - radiator/grille covers, higher temperature thermostat | (all models) | |
Winter Service cooling, fuel, ignition, lubricants - seasonal service | (all models) | |
Wiring Diagram, Hydraulic new model information - window regulator hydraulic | 2006-7-8 | |
Wiring Diagrams - Other Models new model information - chassis | 20th (exc. 2000-01-03-06-10-11) | |
Wiring Diagrams new model information | 17th | |
Wiring Diagrams new model information | 18th | |
Wiring Diagrams new model information | 19th (exc. 1951) | |
Wrist Pins, Loose low mileage, bushing black/corroded - insufficient oil changes | (not specified) |
SC = Service Counselor | SL = Service Letter | STB = Service Technical Bulletin | SSB = Studebaker Service Bulletin |
NOTE: These PDFs were created from High Quality Scans. It is recommended that you Right Click on the link(s) above and do a "Save Target As". This will download the PDF to your machine rather than trying to open and view it over the web.
Disclosures & Disclaimers
Though previously published elsewhere, this work is provided with my full permission for display on the PackardInfo.com website and the personal use of visitors to that site. Any other unauthorized use, however, is expressly prohibited and may be subject to prosecution.
Also, because this index was compiled from documents published by the factory, neither the author nor PackardInfo.com are responsible for errors in content arising from source information.
