Packard Forum Index » Pre-War (1899-1942) Forum

Please Select a Topic below to View Posts

« 1 ... 252 253 254 (255) 256 257 258 ... 287 »

	Topics	Topic poster	Publish time	Replies	Views	Last post time
	1921 Packard "Twin Six"	antiquecarman	2013/5/30 14:41	4	6301	2013/5/30 21:11 by antiquecarman
	29 packard 626 wheel shimmie [1][2][3]	29tons	2012/4/8 17:01	24	6318	2012/4/24 21:07 by tfee
	Oil Pressure line for 1937 [1][2][3]	CORSASEVEN	2014/8/20 20:54	20	6323	2016/7/27 18:15 by 40clubcoupe
	Good prices for clutch parts	Phil Randolph	2008/9/30 14:01	8	6325	2008/10/1 0:04 by flackmaster
	1931 833 boiling over [1][2]	don b	2010/10/2 20:31	10	6333	2010/10/4 21:28 by don b
	Tom's '31 Restoration	Tom (Packin31)	2007/1/11 20:38	6	6337	2007/5/30 21:01 by Tom (Packin31)
	Super 8 repair needed ASAP [1][2]	Skip Hicks	2011/6/22 8:16	11	6344	2011/6/22 23:28 by BigKev
	1941 Lower Metal Radiator Pipe [1][2][3]	Pat and Melanie Westerkamp	2018/9/7 15:13	22	6351	2018/9/11 12:17 by HH56
	Into the Sun [1][2]	Robin Adair	2015/3/19 16:36	15	6359	2015/4/24 17:10 by Ozstatman
	1939 Super 8 wiper issue [1][2]	Chester Sams	2016/12/7 15:20	19	6362	2016/12/9 14:18 by Chester Sams
	1936 Packard 120B Business Coupe engine rebuild [1][2]	pwakem	2012/7/24 4:20	15	6363	2013/1/10 13:36 by Ozstatman
	What kind of oil to use? 1941 Packard 110 [1][2]	Ragtime Kid	2015/5/15 23:08	14	6367	2015/5/22 5:41 by JohnCobb
	Normal Compression Test Values for 1931 Super 8 [1][2]	Stephen Templeton	2022/5/14 17:59	19	6388	2022/6/26 21:32 by Tim Cole
	1937 Battery Draw [1][2][3]	R Howe	2022/10/23 15:34	23	6389	2023/1/7 14:31 by R Howe
	1934 Eight water pump [1][2][3]	Bill Hawley	2022/4/29 22:46	24	6393	2022/7/7 22:07 by Bill Hawley
	1939 packard six [1][2]	mgrambo	2011/12/14 0:34	12	6394	2011/12/27 18:58 by mgrambo
	What is this Packard? [1][2]	BigKev	2022/11/20 16:47	19	6396	2022/11/30 13:57 by JWL
	Need Your Help	JWL	2008/10/14 10:50	9	6416	2008/10/27 9:29 by JWL
	Brake & Clutch Pedals and the Toe Board on a 1932 [1][2]	Marty or Marston	2015/1/25 14:08	14	6420	2015/3/24 21:48 by Marty or Marston
	"Acceptable" bearing clearance [1][2]	Ken_P	2015/4/26 20:50	19	6422	2015/5/1 18:05 by Ken_P
Sorted by