What gauge are the battery cables? Anything smaller than what was stock will cause it to crank hard. Also, did you put fresh fuel in it recently, or is the old stuff from November still in there? It's possible that the gas has went bad, this newer stuff can go bad rather quickly as compared to 20 years ago.

Here are the basics:

1940 120 sedan
Rebuilt starter, brand new battery, new solenoid, good grounds, good cables. Engine has a new head gasket, and the car was just running in November. It stays garaged, as it is being restored.

We are considering the idea of a 12v conversion, but would rather keep the car pure and original. Any ideas out there?

Also, when it does run, once it warms up, it stalls and dies, like it starves for fuel. Has a new gas tank with electric fuel pump. It gets plenty of fuel. The climatic control was one notch rich (stock setting), I adjusted it to about three. It seemed to do okay after it got up to operating temp. But once it cooled down and we tested it again, we had the same issue. Any help on this would be greatly appreciated.

Once we get it to stay running, and we drive it around the block, the car falls on its face in second gear. It has a slight miss at idle, very noticeable while driving, especially in second. The wires are OEM style, but they are arcing to the block. My experience says this isn't normal.

And finally, the Aero-Drive is jammed, luckily not in gear. How is this repaired?

IF you have disassembled the unit per the factory shop manual (which was the first thing that BigKev uploaded to the site, under "Packard Articles"), the seals could just be stuck after decades of co-mingling in the master cylinder bore.

Soak 'em down with some WD-40 and let sit overnight. I bet that will loosen 'em up just enough. If not, try a good penetrating oil, and wait about 15-20 minutes.

P.S. - Thanx for the nice pic of your '53 - and taking time to add it to the Owner Registry here.

Nick--Loyd put it correctly, Lycoming was part of E.L.Cord's conglomerate during the period the ACD cars were manufactured. Packard was a centralized manufacturing entity, they manufactured their own engines, transmissions and rear axles (until the 1956 models, which used purchased Dana rear axles) in a central plant beginning in 1899 in Warren Ohio, then moving to Detroit in 1903, through 1954. The 1955-56 models were assembled in a plant leased from Chrysler, the former Briggs manufacturing plant on Conner ave. that had been suppling all of Packard's post-war bodies. For the 1955-56 model years the (V-8) engines and transmissions were built at Packard's Utica, Michigan plant, a very modern, state-of-the-art facility, and shipped to the Conner plant for assembly into the cars.
ACD at their peak was operating plants in Auburn IN, Connersville IN, Indianapolis, and the Lycoming engine plant in Pennsylvania. The combined size of all those facilities may well have excceded the size of Packard's East Grand Boulevard plant(s)

Hi all,

I'm a new owner of a 52 Packard 300 Sedan. In pretty nice shape I might add. I have obtained a manual and have removed my Power Brake unit. Wheel Cyls are next.

I have removed the large Nut/valve in the reservoir and the circlip retaining the pushrod. According to the manual the rod should slide out. It doesn't and I don't want to apply too much force to do it. Feels like something still needs to be removed somewhere for it to come out.

Any help appreciated.

Also, are there any other forums/discussion groups on Packards?

I'm in Arizona.

Chuck

Attach file:

---

  (44.02 KB)

If my memory serves E. L. Cord's corporate empire included Cord-Auburn-Duesenberg, Eastern Airlines and Lycoming - possibly others of which I am unaware.

Many thanks John!

Am I right in assuming that Packard was a much bigger operation than Auburn?

It seems Auburns Cords and Duesenbergs were powered by Lycoming engines but Packard built their own engines - is this correct?

I would think the actuator would be painted the same color as the tranny/engine whether bronze or green or silver. Mine looks natural now but there is enough bronze on it to determine it was originally that way.

Nick: here are the production numbers for the 810/812 which was produced from 1935 through 1937.

1935 1629

1936 997

1937 281

Total production of Duesys was between 470 and 480 units total from introduction in 1928 to end in the late 30's.


John F. Shireman

nick: First of all welcome to the forum. I don't know if I can find any figures on employment numbers at the Packard Factory between 1935 and 1941, but here are production figures for those years.

1935 52,045

1936 80,978

1937 109,815

1938 50,260

1939 76,573

1940 76,927

1941 66,906


John F. Shireman