The reason I think there is potential to have dropped a 3/8" nut in the cylinder is because when I was working on the starter, I set the 3/8" nut that fastens to ignition wire to the starter terminal on the engine. When I went to reinstall the starter, the nut wasn't there. I thought it had dropped off the engine, or that I had dropped in on the ground

I planned on doing a wet compression test today, but now in fear of turning the engine over and causing more damage I am hesitant to do so.

Since my compression tests are good, is it safe to assume that nothing was damaged if I did drop a nut in the cylinder and thus, if I can able to extract the nut with a magnet removing the head cover is not needed?

And since the dry compression looks so good does it make sense to still do a leak down test (which I also planned for today)?

Hi Ross,

I don't see the fan making contact with the pulley. I did the dry compression test this afternoon and while doing so I began thinking about your idea that it sounds like something may have fallen into a cylinder. I realized that perhaps I was missing a 3/8" nut that connects the ignition wire to the starter and that if something were to have fallen into the cylinder the only one I could see this happening in based on my workflow would be #7.


Well wouldn't you know it, when i compression tested #7 I did hear a very odd noise that potentially resembled a 3/8" nut. If this is true would it impact my compression results? I ask because the numbers (below) were better than I expected

I'm assuming the only way to see if something was dropped in the cylinder is to remove the head?


Dry compression
1 - 120
2 - 90
3 -120
4 - 118
5 - 119
6 - 120
7 - 120
8 - 120

Hi John,

Thanks for sharing your knowledge, I'll look into how to diagnose that!

Hi Ross,

Not that I can think of, the only items I had open that something could have fallen into would be the thermostat opening or the radiator, and the firewall where the starter is mounted but I didn't have anything go missing during those repairs...

Before this the engine had no ticking.

I'm beginning to take some compression readings and when cranking by hand I'm hearing a something that is kind of like a whistling vibration noise that was not there before when i hand cranked it.

Thanks for taking the time to give it another listen.

I have a clip below of the sound while pushing the gas pedal - any suggestions welcome!

https://share.icloud.com/photos/0KlWKrEibuiiexeQ8ffGjSyzA#Venice,_CA



Quote:

@Ross: it is louder than videos I have watched that document a lifter noise - Thats why I am wondering if it may be something else

I experience overheating due to radiator leaks to the extent that the radiator purged fluid from the cap. After braising the holes and starting the engine I now have a loud ticking.

Here are two videos, the first shows the ticking immediately after starting and the second shows the ticking while idling

I've read that lifter ticking is not uncommon but I am unsure if this is lifter ticking, Can anyone advise what this noise may be and how to diagnose?

Ticking at start up:

https://share.icloud.com/photos/0UgaC3l_rD53u0w63cvITtj3A#Venice,_CA

Ticking at idle:

https://share.icloud.com/photos/040_SF3JiIlgdjJRwXEyIbacQ#Venice,_CA

Thanks!

I first went to the DMV to register my Packard which is and always was a California vehicle and has been out of the system after the original owner parked it in 1984.

When I went to the DMV they had no record of f the car, I was very well documented with the original tile and every California registration slip from 1952-1984.

The dmv said I had to schedule an appointment with the CHP to review my car, but the paperwork the DMV gave me said it could be completed by the CHP or a vin verifier. I could tell had I went the DMV path it could have been troublesome and lengthy at best

So I Scheduled an appointment with a vin verifier and renewed through AAA and all went smoothly

Chris: You and I both

Paul: I'd be lying if I were to tell you I hadn't thought about that. This would be an amazing project/investment - that paint can be brought back to an amazing level!!

'55 Clipper Super , $4k - the interior is in amazing condition.

"Field Find!!! Ran until parked 15 years ago. All glass is intact. It still has the plastic covers on front and back seats. No missing parts. I found it and just have too many other projects to take care of this beautiful "boat"."

https://www.facebook.com/marketplace/item/2174541812835738/

Hi Paul, Thank you, I sincerely appreciate the kind words. I was just informed that the interior is complete and I am excited to get the car back and begin enjoying it!

All the best!