Carpet Patterns
|
||||
---|---|---|---|---|
Home away from home
|
Overview
This discussion has come up with some frequency so I decided to pull the carpet out of my 55 Panama, Trim 31 parts car and start measuring. It is the original carpet. Materials First, the material is standard "Daytona weave" carpet with no binding. This is correct for chassis 5540 cars; i.e. Customs and Seniors were a different weave. I will probably will make a post on that info later. The entire carpet uses a 3/32" foam backing, and in the indicated areas, a 3/8" jute underlayment as well. The carpets are glued in place. There are various upholstery or "landau top" adhesives that will suffice. Any adhesive used must be appropriate for both metal and foam/fabric, not just porous materials. For example, don't use Elmer's Glue-All or other such craft glues unless they are specifically compatible with metal as well. Positioning Before I pulled it out, I took these locational photos. General outline. Unfortunately, large sections of the front carpet are already deteriorated, but it is intact enough to be useful. Note also that the rear seat bottom is shifted forward in this photo; do not use it as a locational reference. 5-3/4" between back of front carpet and front of footrest. 2-1/2" typical overlap of rear carpet over footrest carpet. 1-1/2" front of rear carpet center cutout to rear of footrest. Footrest 462747 The footrest carpet uses no jute and is directly adhered. Note the metal construction of the footrest (not shown): it is flat on the front top (neglect the dimple running there for strength) and curves towards the rear. Note on each side where this curve starts. Suggested installation/trimming procedure: - Cut oversize (at least 56"x10"); adhere centered to flat part of top of footrest. - On one side, fold a couple inches of the the front end of the carpet down exactly and adhere the section directly below the flat front area of the footrest. - On the approx. top rear side of the footrest, note the exact spot that the footrest metal begins to curve down. Start the relief cut at this point and cut straight down. - Adhere the carpet to the sloped part of the footrest, then make the second relief cut once it is in place. - Trim around the base and rear. - Trim around the rear cutout. - Repeat on other side starting on Step 2. - Leave excess on transmission tunnel until rear carpet is located. Then cut to size, leaving 2-1/2" overlap. Rear 269118 The rear carpet uses two jute pads. It extends under the footrest by a few inches. Suggested installation/trimming procedure: - Cut jute pad oversize (e.g. 18"x30"). Locate squarely such that the front is aligned with (nearly touching) the footrest base (center and side) and is inboard enough that it is nearly aligned with the edge of the center footrest support. -Trim so that it is at least 2 inches from the front of the rear seat, rear armrest, and door sill plate. - Adhere outboard half, then trim in a straight line following profile of driveshaft tunnel (reference photos). - Repeat on other side. - Cut carpet oversize (at least 25"×66"). Remove rear seat bottom and armrests. - Make center cutout as shown. Curved areas to be cut as quarter-ellipse outlines with the indicated semimajor and semiminor axes. - Locate carpet in car. Use center cutout as reference. Lay down carpet and note position of footrest mounts. Remove carpet and make footrest cutouts as diagrammed. - Adhere carpet in car. Replace rear seat and armrests. Use squares of masking tape on carpet to note critical locations of armrests and seat against carpet. Remove seat and armrests again, and cut carpet to size, in situ, leaving about 1" excess under the sill plate. Replace seat and armrests. Front 269129 I ran out of time to measure the front carpet yesterday. I will return to it later. For now, here is a reference photo.
Posted on: 2024/12/9 8:29
|
|||
1955 400 | Registry | Project Blog
1955 Clipper Deluxe | Registry | Project Blog 1955 Clipper Super Panama | Registry Email (Parts/service inquiries only, please. Post all questions on the forum.) service@ultramatic.info |
||||
|