Re: DO NOT TRUST BTV
|
||||
---|---|---|---|---|
Forum Ambassador
|
Instead of using the Packard setup, what about something like this. Might give more flexibility for the electroboost if the mechanic made your own mounting bracket to the frame and linkage. Anyway, $70 bucks & might be easier to find than a Packard if Mike doesn't have.
Was thinking if the underfloor pedal length was perhaps shortened a couple of inches to drop the suspended to a more normal height and then modified at the end as Eric suggests, the pedal could be attached more securely there where the BTV now attaches. Don't think any ratio change would be needed for shorter travel although a consideration. That end point would now accommodate a bit of rotation but the top end of the suspension where it now has a fixed pivot could have a slotted arrangement instead to allow for sliding to allow the different arcs yet still be secure.jegs.com/
Posted on: 2009/12/20 14:24
|
|||
|
Re: DO NOT TRUST BTV
|
||||
---|---|---|---|---|
Just can't stay away
|
This is certainly a possibility, and not very expensive. I sent a note to Mike to ask if has the manual pedal assy. Of course, he's in Duluth, MN, it's winter, and they've already had snow. I'm thinking it could be May or June before Mike can get to his cars to see if has it.
Any idea what the Packard manual pedal assy attaches to under the car? The pictures in the parts book show a rod that the pedal fits on and pivots on but it doesn't show how the rod attaches to the car. Does it attach to brackets under the body or on the frame?
Posted on: 2009/12/20 14:42
|
|||
Jed
|
||||
|
Re: DO NOT TRUST BTV
|
||||
---|---|---|---|---|
Home away from home
|
The rod goes through holes in the frame. Crawl under your car and you'll see where it goes.
Posted on: 2009/12/20 14:49
|
|||
|
Re: DO NOT TRUST BTV
|
||||
---|---|---|---|---|
Just can't stay away
|
OK, I think I know where the holes are. My car's in the shop now so I can't go check. What holds the rod in the holes?
BTW, the electroboost MC is only 3.25" high and 8.75" long. Think it will fit?
Posted on: 2009/12/20 14:58
|
|||
|
Re: DO NOT TRUST BTV
|
||||
---|---|---|---|---|
Home away from home
|
Springs and a clip holds the rod in place. As for your length, you might be ok, but make sure the fittings on the master point towards the right direction before you buy the master. You don't want to get it all figured out and it not work because the lines will be hitting the frame somewhere.
Posted on: 2009/12/20 15:33
|
|||
|
Re: DO NOT TRUST BTV
|
||||
---|---|---|---|---|
Just can't stay away
|
That's a really good point. The MC has the fittings on the passenger side when placed to the rear of the brake pedal. We'll have to see if there's room for the lines in that position.
Just springs and a clip hold the brake pedal rod in place? There's no brackets or bushings?
Posted on: 2009/12/20 15:48
|
|||
|
Re: DO NOT TRUST BTV
|
||||
---|---|---|---|---|
Home away from home
|
None on the '51-'54 cars that I remember, and definitely no bushings, as the shaft is stationary. It has a "D" shaped end on it IIRC that holds it stationary, and a "C" clip that holds it into the frame. The other end, towards the trans, just holds it in place and keeps it from moving, so there's your "bracket".
Posted on: 2009/12/20 16:01
|
|||
|
Re: DO NOT TRUST BTV
|
||||
---|---|---|---|---|
Just can't stay away
|
I found the attached photo and I think it shows what your referring to. The shaft is stationary and the clutch and brake pedals rotate on the shaft. Got it.
Posted on: 2009/12/20 16:21
|
|||
|
Re: DO NOT TRUST BTV
|
||||
---|---|---|---|---|
Home away from home
|
That's the one.
Posted on: 2009/12/20 16:25
|
|||
|