Re: What is it and what does it fit?
|
||||
---|---|---|---|---|
Forum Ambassador
![]() ![]() ![]() |
Likewise no lookup for 9816; might it be 9616 which was used in the many makes of trucks that used the Hercules W307 engine, also 1949-50 Kaiser & Frazer (those models w/o the vacuum reserve tank)?
Posted on: 2013/4/23 13:34
|
|||
|
Re: What is it and what does it fit?
|
||||
---|---|---|---|---|
Just can't stay away
![]() ![]() ![]() |
#4 somekind of taper lock, maybe for kingpins ?
No idea of year. Really just a guess . . . Packard 385
Posted on: 2013/4/25 9:54
|
|||
|
Re: What is it and what does it fit?
|
||||
---|---|---|---|---|
Home away from home
![]() ![]() ![]() |
This part looks like the one in the picture on Packard Information. Is it only for the 120?
https://packardinfo.com/xoops/html/modules/myalbum/photo.php?lid=1178&cid=41
Posted on: 2013/6/6 20:39
|
|||
|
Re: What is it and what does it fit?
|
||||
---|---|---|---|---|
Home away from home
![]() ![]() ![]() |
Any ideas on this one? Does the cast number match the part number?
Any ideas on the the other parts?
Posted on: 2013/6/6 20:50
|
|||
|
Re: What is it and what does it fit?
|
||||
---|---|---|---|---|
Forum Ambassador
![]() ![]() ![]() |
The last 2 are the steering idler arm support from the Clipper-style front suspension. I suspect it's the earlier style (pre 1950?) because at some point the greaseable screw-thread joint was replaced by a simple rubber bushing. It might be original but could also be an aftermarket piece as the later rubber-bushed units didn't give the greatest service life and Moog and others did a brisk business with replacements with a greaseable joint.
As to the first picture, the senior cars also used the center link steering geometry but I can't tell if this is for a junior, a senior, or if they were different but the parts listing will tell you if they shared the same part#. With regard to the numbers on the parts, just look them up in the master parts listing - if they are not listed they are almost certainly casting or forging numbers which are often only a few digits away from a finished part number. Often a single raw forging or casting would have been used to make multiple finished part numbers.
Posted on: 2013/6/7 0:20
|
|||
|
Re: What is it and what does it fit?
|
||||
---|---|---|---|---|
Home away from home
![]() ![]() ![]() |
OD,
Thank you again.
Posted on: 2013/6/8 11:39
|
|||
|
Re: What is it and what does it fit?
|
||||
---|---|---|---|---|
Home away from home
![]() ![]() ![]() |
What a day sorting parts!
Part identifying is hard enough without part numbers, but then there are parts like this one. It has a clearly readable part number, even has the group number. I looked multiple times in the 1948-1954 parts manual, the 55-56 book as well. No luck. I went through the service technical bulletins, and then the service counselors, starting with 1954 and going backwards. OD, I found this one! www.packardinfo.com/xoops/html/downloads/SC/SC-VOL27NO6.pdf I guess putting theses numbers in an updated parts book was something just not high priority. The fact that the group number was listed made me think it was in a parts book some where. Those old counter/parts guys got a work out.
Posted on: 2013/6/8 17:48
|
|||
|
Re: What is it and what does it fit?
|
||||
---|---|---|---|---|
Home away from home
![]() ![]() ![]() |
welcome to the club. :)
Posted on: 2013/6/8 18:33
|
|||
|
Re: What is it and what does it fit?
|
||||
---|---|---|---|---|
Home away from home
![]() ![]() ![]() |
Found this one, is it Packard?
Posted on: 2013/12/7 16:32
|
|||
|