Re: 1956 Packard Patrician Rebuild Project
|
||||
---|---|---|---|---|
Home away from home
![]() ![]() ![]() |
If you bend the "J", won't the force of the unloading and loading bend it back?
Posted on: 2014/6/28 23:22
|
|||
|
Re: 1956 Packard Patrician Rebuild Project
|
||||
---|---|---|---|---|
Home away from home
![]() ![]() ![]() |
mock up
Posted on: 2014/6/29 17:22
|
|||
[url=https://packardinfo.com/xoops/html/modules/
|
||||
|
Re: 1956 Packard Patrician Rebuild Project
|
||||
---|---|---|---|---|
Home away from home
![]() ![]() ![]() |
The mock up location, of the "J" bar, will it allow you to use the tool with the body on the frame?
Posted on: 2014/6/29 21:06
|
|||
|
Re: 1956 Packard Patrician Rebuild Project
|
||||
---|---|---|---|---|
Home away from home
![]() ![]() ![]() |
This particular one I am building up specifically for down and dirty (safely) with body off. I will eventually make a copy of the factory original for body on applications. Howards print will help big time, I had it pegged at 12" with a 30 deg bend where the print shows 9" with a 19 deg. I will use my buddies hydraulic bender at his fab shop to make the factory "J" bar when the time comes. I have the cradle all drawn up but that will be a later project.
Posted on: 2014/6/29 21:21
|
|||
[url=https://packardinfo.com/xoops/html/modules/
|
||||
|
Re: 1956 Packard Patrician Rebuild Project
|
||||
---|---|---|---|---|
Home away from home
![]() ![]() ![]() |
Ok,
Did you look at Henry project blog pictures? https://packardinfo.com/xoops/html/modules/newbb/viewtopic.php?topic_id=653&viewmode=flat&order=ASC&type=&mode=0&start=350
Posted on: 2014/6/29 21:37
|
|||
|
Re: 1956 Packard Patrician Rebuild Project
|
||||
---|---|---|---|---|
Home away from home
![]() ![]() ![]() |
Yes, Henry does an awesome job documenting. I wish I documented a little better, but I am so into the work, I don't want to stop.
Posted on: 2014/6/30 9:28
|
|||
[url=https://packardinfo.com/xoops/html/modules/
|
||||
|
Re: 1956 Packard Patrician Rebuild Project
|
||||
---|---|---|---|---|
Home away from home
![]() ![]() ![]() |
Well, Failure of the screw jack. The rest of the rig held great back to the T/L.
Posted on: 2014/7/1 18:05
|
|||
[url=https://packardinfo.com/xoops/html/modules/
|
||||
|
Re: 1956 Packard Patrician Rebuild Project
|
||||
---|---|---|---|---|
Forum Ambassador
![]() ![]() ![]() |
Well that is aggravating. It must explain the reason for the big J arrangement and the long screw working from opposite side of the car. That would always keep the screw in tension so it couldn't bend.
Posted on: 2014/7/1 18:47
|
|||
Howard
|
||||
|
Re: 1956 Packard Patrician Rebuild Project
|
||||
---|---|---|---|---|
Home away from home
![]() ![]() ![]() |
The T/L arm is 1/2 hole high for centering alignment, and I can not get it down to center to insert the tool.
Even with 800 pounds on the frame and jacking the rear axle, still can not get it to rotate to center still staying about a half hole off.
Posted on: 2014/7/1 20:25
|
|||
[url=https://packardinfo.com/xoops/html/modules/
|
||||
|