Re: New Gas Tank Issue
|
||||
---|---|---|---|---|
Home away from home
![]() ![]() ![]() |
Based on the pic of the cut-away tank in post # 78 above it most likely that way for the SUPPORT bracket inside of the tank to help support the filler neck.
However, it it might aid in preventing gas from running up the tube BUT i would expect to see a baffle in the tank too. So the extended part of the filler neck is probably not an issue for the LEAK problem. Only to add strength to supporting the filler neck.
Posted on: 2016/8/26 17:51
|
|||
VAPOR LOCK demystified: See paragraph SEVEN of PMCC documentaion as listed in post #11 of the following thread:f
https://packardinfo.com/xoops/html/modules/newbb/viewtopic.php?topic_id=7245 |
||||
|
Re: New Gas Tank Issue
|
||||
---|---|---|---|---|
Home away from home
![]() ![]() ![]() |
I decided to check my '56 Patrician and I can confirm that there's no notch in the filler neck. Cheers, John
Posted on: 2016/8/29 3:26
|
|||
|
Re: New Gas Tank Issue
|
||||
---|---|---|---|---|
Home away from home
![]() ![]() ![]() |
There were no smog or pollution regulations in those days and all Packards were manufactured in Detroit so a "regional" shorted of vented caps could not have been an issue. There were plenty of manufacturers of caps who would make any type in any quantity required. The parts book indicates only one part number so there is only one type, perhaps with the exception of commercial cars.
If you have been keeping up with this post you will see a photo of our ALL ORIGINAL 1952 Patrician gas filler with a notch. Thus the notch/no notch is not limited to 1956.
Posted on: 2016/8/29 11:06
|
|||
|
Re: New Gas Tank Issue
|
||||
---|---|---|---|---|
Forum Ambassador
![]() ![]() ![]() |
I have been following and I don't believe anyone else has posted a photo showing a notch on their original tank. Rocky mentioned having a notch but didn't say if his was the same as the 52 or the repro. The photo of the notch on the 52 appears different than the repro notch. It is higher which is no big deal but appears to be much shallower so with the gasket pressing on it maybe a very small opening. It is blurry so hard to tell but looks like it narrows considerably at the inside edge. The repro notch is quite pronounced. Mine has no notch and the unknown year tank Ross cut apart appears to have none either.
One thing I cannot wrap my head around is why on VesPacs photo the rim looks so different than on other tanks including the 52. It must be optical illusion due to shading or is there something different in his rim construction. Sure would like to see a photo at a different angle. On his straight on photo it almost looks like the cut out portion wraps over the top rather than the bottom. I know that cannot be or there would be a huge hole but it sure looks different in the photo than my tank, the one Ross cut apart and the 52.
Posted on: 2016/8/29 11:54
|
|||
Howard
|
||||
|
Re: New Gas Tank Issue
|
||||
---|---|---|---|---|
Home away from home
![]() ![]() ![]() |
As promised, I inspected our cutaway sample of our reproduction 51-56 tank. Even though I already knew the answer I checked it this morning as I wanted to be 100% sure of what I said. The inlet is secured to the bottom of the tank with a welded bracket, exactly like original.
Those who "guess" or speculate about the construction do a disservice to all other forum members, just sowing unsurety and doubt about our professionalism and the quality of our products. If you KNOW something is wrong , by all means alert the public, if you THINK something is wrong then write or call us and we will investigate and report back.
Posted on: 2016/8/29 11:55
|
|||
|
Re: New Gas Tank Issue
|
||||
---|---|---|---|---|
Home away from home
![]() ![]() ![]() |
THose that have the tank with a "notch" need to look close a the FULL LENGTH of the filler tube. All the way from the top of the filler tube down to the bottom of the tube near the tank.
On my 56 OEM tank the filler tube is ONE CONTINUOUS TUBE. i.e. there is no evidence that there is any SEAM of any type between the top of the tube and the bottom of the tube. i.e. that the filler tube is made from ONE piece of tubing and bent to form. If the fille tube that has the notch has a SEAM (a radial seam) as if it were made of 2 DIFFERENT tubes welded to gether in some way then that would indicate that the top part of the tube, the part that has the notch, is probably some retro fitted part from some other application thatwould require a different cap. Probably a caap with a baffle tubbe attached to it as i have outlined a few posts above. Someone ook at their filler tube with the notch to see if it appears to havee been maade from TWO different tubes welded together.
Posted on: 2016/8/29 12:28
|
|||
VAPOR LOCK demystified: See paragraph SEVEN of PMCC documentaion as listed in post #11 of the following thread:f
https://packardinfo.com/xoops/html/modules/newbb/viewtopic.php?topic_id=7245 |
||||
|
Re: New Gas Tank Issue
|
||||
---|---|---|---|---|
Home away from home
![]() ![]() ![]() |
Our original '52 tank has a seamless fill tube and a notch and no a
Sherman tank or earthmover part was not put on with bubble gum .
Posted on: 2016/8/29 13:58
|
|||
|
Re: New Gas Tank Issue
|
||||
---|---|---|---|---|
Home away from home
![]() ![]() ![]() |
ok. But what about the REproduction tank??? Is the filler tube with no seam like the OEM tank????
Posted on: 2016/8/29 14:26
|
|||
VAPOR LOCK demystified: See paragraph SEVEN of PMCC documentaion as listed in post #11 of the following thread:f
https://packardinfo.com/xoops/html/modules/newbb/viewtopic.php?topic_id=7245 |
||||
|
Re: New Gas Tank Issue
|
||||
---|---|---|---|---|
Home away from home
![]() ![]() ![]() |
Yes, every one of the Packard tanks we have had made have seamless filler tubes, just like the originals.
Posted on: 2016/8/29 15:05
|
|||
|