Packard Forum Index » V-8 (1955-56)

Topic: fuel ine size

Bottom

Previous Topic

Next Topic Register To Post

Bowman Davis

fuel ine size

Home away from home

What is the correct (or minimum) size fuel line from the tank to fuel pump for a 56 pat.
Thanks,

Posted on: 2009/6/8 21:43

Craig Hendrickson

Re: fuel ine size

Home away from home

Original is 5/16".

If I were going to replace it, go to 3/8", but that's just my preference. 5/16" is sufficient since almost no one is drag racing these cars any more or even running them full throttle for a bit.

However, an electric "pulse" pusher pump is a good idea to 1) prevent vapor lock when hot and 2) full an empty carb after it has sat for a while and the modern gas evaporates.

Craig

Posted on: 2009/6/8 21:51

Nuke them from orbit, it's the only way to be sure! Ellen Ripley "Aliens"
Time flies like an arrow. Frui

Dave Harrison

Re: fuel ine size

Just can't stay away

Hi,
On the same subject does anyone have a part number maybe NAPA or where a replacement can be obtained for the filter element inside the glass bowl fuel filter at the inlet of the carb. Mine is a 55 400 and from pictures of other 55 engine bays it looks to be original.
Thanks,
PackarddaveUK.

Posted on: 2009/6/9 10:27

Rusty O\'Toole

Re: fuel ine size

Home away from home

$Rusty O\'Toole$

5/16 should be ample. The only car I know that came with a 3/8 fuel line was the Chrysler race hemi in the late 60s. Even their hi perf 440 came with 5/16.

Posted on: 2009/6/9 10:53

Bowman Davis

Re: fuel ine size

Home away from home

Thanks for the info, I'll stick with the 5/16" original size.
Original line was probably reg. steel,NOT SS, correct?

Posted on: 2009/6/9 13:28

Craig Hendrickson

Re: fuel ine size

Home away from home

Regular steel fuel line.

Posted on: 2009/6/9 13:34

Nuke them from orbit, it's the only way to be sure! Ellen Ripley "Aliens"
Time flies like an arrow. Frui

Craig Hendrickson

Re: fuel ine size

Home away from home

Quote:

5/16 should be ample. The only car I know that came with a 3/8 fuel line was the Chrysler race hemi in the late 60s. Even their hi perf 440 came with 5/16.

Gen-2 (1970-81) Firebirds all had 3/8 lines. However, part of that may have been due to the fuel-return (1/4in) lines used on the emission-control vehicles starting in the early 70s which required more raw fuel flow given the return line bleed off.

Craig

Posted on: 2009/6/9 13:37

Nuke them from orbit, it's the only way to be sure! Ellen Ripley "Aliens"
Time flies like an arrow. Frui

Rusty O\'Toole

Re: fuel ine size

Home away from home

$Rusty O\'Toole$

They are 2 different things. I was talking about cars with carburetors. Later model fuel injection cars have a completely different setup.

5/16 fuel lines are pretty well standard equipment on American cars from before fuel injection. In the interest of clarity I left it at that.

Posted on: 2009/6/9 16:31

Craig Hendrickson

Re: fuel ine size

Home away from home

Quote:

They are 2 different things. I was talking about cars with carburetors. Later model fuel injection cars have a completely different setup.

I am also talking about carburated engines, QJet in the case of Gen-2 Firebirds.

Craig

Posted on: 2009/6/9 17:48

Nuke them from orbit, it's the only way to be sure! Ellen Ripley "Aliens"
Time flies like an arrow. Frui

Board index » Discussion » V-8 (1955-56) » fuel ine size

Top

Previous Topic

Next Topic

	';
Hello and welcome to Packard Motor Car Information! If you're new here, please register for a free account.