Misc. New Mfg. Packard Parts
|
||||
---|---|---|---|---|
Home away from home
|
Posted on: 4/27 5:25
|
|||
|
Re: New Engine
|
||||
---|---|---|---|---|
Home away from home
|
I agree with Mal, I installed a 54 327 bored out to 340 and run a Holley 600 and Packard R6 OD into my 1938 Richards 1601 ( 120). I literally tore all of the spot welds from the axle tube doing a "rabbit" getaway ( diff rotates and separates the drive train). There should be plenty of good serviceable going 327's in the big pond that is the US. In OZ and NZ we have a very small pond with not too many Packards. The $700 Packard 327 on offer should do the trick. Peter T
Posted on: 4/27 2:11
|
|||
I like people, Packards and old motorbikes
|
||||
|
Re: New Engine
|
||||
---|---|---|---|---|
Forum Ambassador
|
Quote:
su8overdrive wrote:.......get a four-barreled 327 from a 1953 or '54 donor......... Be aware though that a '53/'54 engine ia not a straight drop in into your '49. Engine mounts changed at some stage between earlier year 288/327's and later year 288/327's. I don't know the change date/year, but it happened. Maybe one of our more in-depth/knowledgeable Members can supply more specific information?
Posted on: 4/27 0:06
|
|||
Mal
/o[]o\ ==== Bowral, Southern Highlands of NSW, Australia "Out of chaos comes order" - Nietzsche. 1938 Eight Touring Sedan - SOLD 1941 One-Twenty Club Coupe - SOLD 1948 Super Eight Limo, chassis RHD - SOLD 1950 Eight Touring Sedan - SOLD What's this? Put your Packard in the Packard Vehicle Registry! Here's how! Any questions - PM or email me at ozstatman@gmail.com |
||||
|
Re: Don’s 1937 (120) 138CD Deluxe Touring Limo
|
||||
---|---|---|---|---|
Webmaster
|
I would exactly mark the washer location of the center pivot bolt on the bottom side of the front cross member to aid in getting it back in the same position which will help with front end sheet metal alignment if your aligned is currently good between the fenders, hood, firewall and grill shell.
Also, if you could how many turns it took to remove the nut, that would help to get it back to the same "squish" on the rubber mount there.
Posted on: 4/26 22:56
|
|||
-BigKev
1954 Packard Clipper Deluxe Touring Sedan -> Registry | Project Blog 1937 Packard 115-C Convertible Coupe -> Registry | Project Blog |
||||
|
Re: Don’s 1937 (120) 138CD Deluxe Touring Limo
|
||||
---|---|---|---|---|
Home away from home
|
Thanks, Kev
Sounds like what I was thinking…a lot of disassembly. If I’m to attempt this, it’s going to take some time for me to work up the nerve!
Posted on: 4/26 22:07
|
|||
|
Re: Don’s 1937 (120) 138CD Deluxe Touring Limo
|
||||
---|---|---|---|---|
Webmaster
|
There are bolts at the top and sides, and the large pivot bolt at the bottom. Obviously the firewall rods are in the way as is the hood.
If it was possible to get all the bolts out and remove the large nut underneath the front cross member, then you'd have to tilt the radiator in and up to get that bottom bolt to clear the cradle. I'd image the fan and waterpump would be in the way. Otherwise, you'd have to do what I did. Remove hood, remove bumper and supports. Remove Headlights, remove fenders, remove nuts from the firewall wall rods. Remove lower pivot bolt nut, remove all hoses. Take off the grille surround. Then you can pull the core support, and radiator out as an assemble. Lay it down on a blanket and remove the bolts that holds it to the core support and also that bottom pivot bolt. Reverse the process to install. I should have many of the pictures in my blog.
Posted on: 4/26 21:58
|
|||
-BigKev
1954 Packard Clipper Deluxe Touring Sedan -> Registry | Project Blog 1937 Packard 115-C Convertible Coupe -> Registry | Project Blog |
||||
|
Re: Don’s 1937 (120) 138CD Deluxe Touring Limo
|
||||
---|---|---|---|---|
Home away from home
|
Next question….
If I were to remove the radiator to get it to a shop, how does it come out? I know the front clip can come off as one assembly, but I don’t have the space or hoist to do that? Also, If I go that route, then it opens the door give some attention to other items that I don’t know if they were tended to back in 2004. Such as, timing chain, timing pan seals, center steering bearing etc… The front motor mount was just replaced by Allen. Any thoughts on this approach?
Posted on: 4/26 21:42
|
|||
|
Re: Don’s 1937 (120) 138CD Deluxe Touring Limo
|
||||
---|---|---|---|---|
Home away from home
|
Regarding my fuel issue…I know my heat riser is out of commission….rusted/stuck and no counter weight. Based on what others have said, I’m pretty confident that it must be in the open position. But, I don’t know how to verify that?
Can someone tell me how I can verify?
Posted on: 4/26 21:36
|
|||
|
Re: Goddess of Speed print
|
||||
---|---|---|---|---|
Home away from home
|
Good chance to brag! I got this for Christmas from my Daughter Sam, she made it with her Cricut, a computer driven cutter, she did the artwork and then she cut it in a series of vinyls.
Bob J.
Posted on: 4/26 21:30
|
|||
|