Hello and welcome to Packard Motor Car Information! If you're new here, please register for a free account.  
Login
Username:

Password:

Remember me



Lost Password?

Register now!
FAQ's
Main Menu
Recent Forum Topics
Who is Online
244 user(s) are online (174 user(s) are browsing Forums)

Members: 2
Guests: 242

dallas, TxGoat, more...
Helping out...
PackardInfo is a free resource for Packard Owners that is completely supported by user donations. If you can help out, that would be great!

Donate via PayPal
Video Content
Visit PackardInfo.com YouTube Playlist

Donate via PayPal




No Ignition Key
#1
Home away from home
Home away from home

Tall Steve
See User information
The shop that has my 53 Clipper for 8 months has lost the only ignition key I had. What are the options? Thanks in advance. Steve

Posted on: 2018/12/14 12:20
Even the most difficult situations can be learning situations.

1953 Packard Clipper
1957 Chevrolet BelAir
2004 Chevrolet Corvette
 Top  Print   
 


Re: No Ignition Key
#2
Forum Ambassador
Forum Ambassador

HH56
See User information
Some options.

1. If you need to operate the car right away buy an inexpensive universal ign switch and install that as a temp while one of the other options is explored. If you are not worried about an extra key or looks it could be a permanent solution but that doesn't solve the issue of the ign key normally being the same one used for doors. Unless the ign key was changed before to a third key you would still be inconvenienced not having the proper key.

2. It has been reported there are a limited number of key combinations (250 I think it was) and if there is someone in the area with a decent selection see if one of those will fit. Possibly David Moe at Seattle Packards or ??

3. Remove the entire ignition assy and if you have a good local locksmith have him pick the lock and make a new key. If no locksmiths are local Jesser's can do it but no idea on the cost.jessersclassickeys.com

4. Modify the ign switch so the lock cylinder can be removed in the off position without the key. This is by far the most risky and takes a bit of care when drilling the needed access hole but I have done it on several with good results. Once the cylinder is out there is usually a number on the side or end so the proper key can be ordered from Jesser's or a local locksmith or, if desired and you have another key and don't need the door key the lock pins can be filed down to match the spare key.

If you elect to try the mod, here are a few photos and a description of what is needed. The cylinder is held in the lock by a spring loaded retaining clip which rides in a groove. The clip needs to be depressed against the spring with a blunt pin while the cylinder is pulled slightly until the clip enters the cylinder bore and remains depressed. Normally the lock will have a single access hole where the clip is visible with the cylinder in a certain position. The lock cylinders will interchange over many years and type locks so there could be versions where the key fits blunt side up or notch side up . On this 23-26 series ign lock the key was notch side up and needs to be in the ON position to the right. That lines the clip up with one of the holes and with the blunt pin you push in on the clip while pulling the key and cylinder out. Since there are two factory holes a different version cylinder might use the other hole and need turning to the left.

With the key not available and the cylinder in the off position the clip will be hidden. There needs to be a hole CAREFULLY drilled where the clip is positioned when off. On this 21-26 ign lock, as you are looking at the switch as it is positioned in the car, the notch side of key was up so the hole needed to be on the right side but if it happens to have one of the other cylinder versions with the key blunt side up it may need to be on the left side. It is impossible to know exactly which version you have so be prepared to drill the opposite side at the same respective position if the clip does not appear under the new hole.

The new hole needs to be the same size or maybe a tiny bit larger than the existing holes and lined up to be the same distance front to back. That part is very important so the hole will be over the clip. Using a slightly larger hole covers up a bit of imprecision as long as the size doesn't go overboard. The BE VERY CAREFUL part comes in when doing the depth. The retaining clip will be under the hole and if you go too deep or drill carelessly you can bite into and bend or otherwise damage the clip so it will not be able to be pushed against the spring and released.

Attach file:



jpg  (74.46 KB)
209_5c1422ae577c4.jpg 867X939 px

jpg  (52.79 KB)
209_5c1422bc572d0.jpg 879X707 px

jpg  (28.74 KB)
209_5c1422c61faf9.jpg 551X559 px

jpg  (87.34 KB)
209_5c1422d3c99e4.jpg 969X929 px

jpg  (57.62 KB)
209_5c1422df62b8e.jpg 851X735 px

jpg  (67.48 KB)
209_5c1422f20a792.jpg 794X937 px

Posted on: 2018/12/14 16:39
Howard
 Top  Print   
 


Re: No Ignition Key
#3
Forum Ambassador
Forum Ambassador

Owen_Dyneto
See User information
1. Correct, only 250 different keys so try your local Packard buddies first.

2. If you have to move the car, just hot-wire it. Hot battery feed to the coil and then just jump the starter solenoid.

Then pursue the options above by HH.

Posted on: 2018/12/14 17:12
 Top  Print   
 









- The following Google Ad-Sense Advert helps fund the cost of providing this free resource -
- Logged in users will not see these. Please Join and Donate to help support the website -
Search
Recent Photos
Photo of the Day
Recent Registry
Upcoming Events
46th Annual Texas Packard Meet
04/03/2025 - 04/06/2025
Packard Salon - Calling All Twelves
05/27/2025 - 05/29/2025
58th Annual National Meet
05/31/2025 - 06/06/2025
AACA Fall Meet (Hershey)
10/06/2025 - 10/10/2025
South Pacific Packard Club 2026 Rally
03/22/2026 - 03/28/2026
Website Comments or Questions?? Click Here Copyright 2006-2024, PackardInfo.com All Rights Reserved