Re: Standard shift in 56 Packards & Clippers
|
||||
---|---|---|---|---|
Forum Ambassador
![]() ![]() ![]() |
Dave, I respectfully disagree.
There are three oil pumps. #1 same as 1955 #2 as described in 56-T20 is the same oil pump but has a threaded bolt with copper washer replacing the retainer 440655 and cotter pin. #3 Is a different casting and is listed as part #6480508 which has a shorter piston #6492432 and a corresponding shorter spring #6492434. This third pump also has the bolt with copper washer keeping the spring-valve combination sealed in its chamber. I have this third pump in my 400 - it came from my parts car, and the number cast into the pump body is a 7 digit number beginning with "6". The older pump (#1 and #2) have a six digit number beginning with "440". I will try to get the Utica number from my parts car block tomorrow.
Posted on: 2013/10/25 0:51
|
|||
|
Re: Standard shift in 56 Packards & Clippers
|
||||
---|---|---|---|---|
Forum Ambassador
![]() ![]() ![]() |
Thanks Randy for the info on the oil pumps, I stand corrected and knew better. But my point in the post was not about oil pumps but about how many engines were actually made for standard transmission prior to May 3rd.
Posted on: 2013/10/25 7:56
|
|||
|
Re: Standard shift in 56 Packards & Clippers
|
||||
---|---|---|---|---|
Forum Ambassador
![]() ![]() ![]() |
Quote:
Am I interpreting this correctly? Sure looks like solid evidence to support a count - at least as a starting point. Quote: This TSB dated May 3, about 6 weeks from the final plant shutdown, gives the Utica engine #s at the time of the changeover to the final oil pump. While the STB is dated May 3, you must have overlooked the point in the preceeding text of that bulletin, advising that the revised pump design was introduced in engine production on April 10 - another 4 weeks prior to shutdown of final assembly. However, I don't know what kind of lead time they had in mind between engine production and final vehicle assembly.
Posted on: 2013/10/25 9:30
|
|||
|
Re: Standard shift in 56 Packards & Clippers
|
||||
---|---|---|---|---|
Forum Ambassador
![]() ![]() ![]() |
BH, thanks for pointing that out about the April date. One thing occurs to me about the DD-1001. Either it WAS the first standard shift engine for the Pat/400, or it will be if it is ever actually built.
Posted on: 2013/10/25 9:33
|
|||
|
Re: Standard shift in 56 Packards & Clippers
|
||||
---|---|---|---|---|
Forum Ambassador
![]() ![]() ![]() |
randyberger wrote:
Quote: Dave, I respectfully disagree. Not to take this thread any further off course, but there were TWO (2) production versions of the oil pump for Packard vehicle applications: * The original/early design for 55-56 with the relief valve retained by a cup and one cotter pin. * The late design pump introduces late in 56th Series production, per STB 56T-20, with a plugged relief valve port. Although the parts book shows NO listing for this pump as a complete assembly, it does list other details for this pump - like a SHORTER relief valve and spring. BTW, I have a NOS late design oil pump body, which bears the casting number 6492430, near the vacuum pump vent. The finished body (for service) is P/N 6492431, which uses the P/N 6492432 valve and P/N 6492434 spring. However, there are TWO (2) factory-sanctioned variations of the original oil pump that might be found in Packard vehicle: * The original/early design for 55-56 modified as part of a confidential field test, with the relief valve bore plugged, the cotter pins holes brazed shut, and the original relief valve purposely scored. Again, this trail was very limited in scope durarion - may not be many of them out there. * The original/early design for 55-56 modified per STB 56T-20, with the relief valve retainer replaced by a sump tube, held by two roll pins. So, there it's possible to find any one of FOUR (4) styles of oil pump in a V8 Packard model. Now, P/N 6480508 is actually the oil pump assembly for the 56J Golden Hawk (Gr. 116, in the Studebaker parts book), which has a flat bottom plate, rather than a separator plate and vacuum pump. The serviceable details show only one relief valve, P/N 445067 (Gr. 117), which is the same as the original pump used in 55-56 Packard vehicle applicataions. Yet, while the Studebaker parts book shows only ONE oil pump for the 56J, Studebaker Service Letter No. 936 recommended installation of the sump tube kit on 56J models and ALSO advised of a new plugged pump design for 56J production - just not listed in their parts book. So, there's TWO (2) more production verisions and ONE (1) more factory-sanctioned variant. Throw in the version of the pump for Nash-Hudson vehicle applications and we've got FIVE (5) production versions and THREE (3) factory-sanctioned variations.
Posted on: 2013/10/25 9:40
|
|||
|