Re: Ultramatic Transmission External Trans. Fluid Cooler - 1956
|
||||
---|---|---|---|---|
Home away from home
|
Should be clean as it was rebuilt several years back.
Posted on: 2009/4/27 20:22
|
|||
|
Re: Ultramatic Transmission External Trans. Fluid Cooler - 1956
|
||||
---|---|---|---|---|
Home away from home
|
Would slip sometimes when starting in High or once in a while when going from second to high gear. More noticeable on sustained driving.
Is the transmission fluid level best checked with the fluid at operating temp or cold just after it is started? Thanks
Posted on: 2009/4/27 20:25
|
|||
|
Re: Ultramatic Transmission External Trans. Fluid Cooler - 1956
|
||||
---|---|---|---|---|
Home away from home
|
Had the mechanic tighten the filler pipe as it was leaking there.
Posted on: 2009/4/27 20:26
|
|||
|
Re: Ultramatic Transmission External Trans. Fluid Cooler - 1956
|
||||
---|---|---|---|---|
Home away from home
|
Thanks,
Is it much of a job to disconnect the hoses to the old cooler and reroute to the front of the car?
Posted on: 2009/4/27 20:28
|
|||
|
Re: Ultramatic Transmission External Trans. Fluid Cooler - 1956
|
||||
---|---|---|---|---|
Forum Ambassador
|
With your mention of the slipping, would check the linkage adjustment very carefully. Too low a throttle pressure caused by bad linkage adjustment will cause all the slipping problems you mention. Unfortunately, so will a bushing that is leaking pressure.
Posted on: 2009/4/27 22:10
|
|||
|
Re: Ultramatic Transmission External Trans. Fluid Cooler - 1956
|
||||
---|---|---|---|---|
Home away from home
|
Proper adjustment of transmission throttle linkage is indeed pretty critical as to shifting points on the Ultramatics. Should be covered in the Shop manual for your car. There was a rubber (I think) spacer bushing in the throttle linkage on my car that was worn out that initially caused me some problems in this area when I was trying to line out the transmission. I, too, have an add-on transmission oil cooler on my car of the type described in Eric's post above (it came from JEGS about three years ago) in addition to the factory one - also subscribing to the belief that you can't over cool transmission fluid.
Posted on: 2009/4/27 23:19
|
|||
|
Re: Ultramatic Transmission External Trans. Fluid Cooler - 1956
|
||||
---|---|---|---|---|
Home away from home
|
FLAT TUBE, not ROUND TUBE. This is KEY. What you are looking for is something like this: B&M Trans Cooler
There's several different styles and sizes, but it's important that the tubes themselves be flat, not round. This means that there's more surface area as compared to a round tube and fin type that just makes a couple of passes through the fins. And it's not "new and improved", they've been around for years, just not standard in Ultramatic equipped Packards. The worst thing you can do to a hot engine is have even hotter ATF heating up the coolant even more. An external fluid to air trans cooler is the only way to fly.
Posted on: 2009/4/28 0:33
|
|||
|
Re: Ultramatic Transmission External Trans. Fluid Cooler - 1956
|
||||
---|---|---|---|---|
Home away from home
|
Eugene. Who rebuilt the transmission????
Posted on: 2009/4/28 6:09
|
|||
VAPOR LOCK demystified: See paragraph SEVEN of PMCC documentaion as listed in post #11 of the following thread:f
packardinfo.com/xoops/html/modules/newbb/viewtopic.php?topic_id=7245 |
||||
|
Re: Ultramatic Transmission External Trans. Fluid Cooler - 1956
|
||||
---|---|---|---|---|
Home away from home
|
Packard Motor Car in CT.
Posted on: 2009/4/28 6:55
|
|||
|