Re: Packard V8 in a Studebaker C-cab truck
|
||||
---|---|---|---|---|
Not too shy to talk
|
Jack...you are definitely correct in the attention to detail when putting these things together. Fortunately my father is an automotive machinist and mechanic and has massive experience with this. What he has found is that he has a 4 speed manual transmission out of an old Mustang II that is a perfect fit other then machining a little length off the snout that connects to the engine. I have a new Ford 9" rear end going in it as well. I have the luxury right now that the truck is at a bare frame level so we can work slowly and diligently on getting all the alignments etc. correct.
Steve
Posted on: 2010/11/30 13:15
|
|||
|
Re: Packard V8 in a Studebaker C-cab truck
|
||||
---|---|---|---|---|
Home away from home
|
Jack,
Does mean that the A/C comp bracket and acc. drive might be commercially available for the Packard V8? Sure would be nice for those of us that lack the tools for fabrication. Bill
Posted on: 2010/11/30 13:32
|
|||
|
Re: Packard V8 in a Studebaker C-cab truck
|
||||
---|---|---|---|---|
Home away from home
|
Quote:
Does mean that the A/C comp bracket and acc. drive might be commercially available for the Packard V8? Probably not. I've talked with the president of Vintage Air and he has agreed to look at what I come up with. The problem with keeping the OEM generator and PS pump requires the AC to sit on top and displace either the oil filter or the oil filler tube. Neither is an ideal solution. Quote: he has a 4 speed manual transmission out of an old Mustang II that is a perfect fit other then machining a little length off the snout that connects to the engine. Borg-Warner built transmissions for all the major manufacturers. Ford used a lot of them. Studebaker and Packard used the Ford bolt pattern version of the T85, T86 and the T10. In '63 Ford started making their own transmissions and kept the B-W bolt pattern until '65. Most of the Ford manual transmissions after '65 were a dual pattern and would fit either the earlier B-W or later Fords, with a change of front bearing retainer. Ford had two different input shaft lengths, big block and small block. So bottom line, yes, most Ford manual transmissions can be made to fit a Packard. As can AMC and Studebaker versions. Because Stude trucks with the 4-speed are ALWAYS geared way too low for today's highway speeds and because I wanted to keep my Budd wheels, an overdrive was mandatory. I could have gone with using a Studebaker or AMC or Ford T10 and adding an overdrive, but I didn't like the passenger car ratios for a 3/4t truck. You chose a Ford 9", which has a different bolt pattern, but you've probably got different goals than I had. jack vines
Posted on: 2010/11/30 15:51
|
|||
|
Re: Packard V8 in a Studebaker C-cab truck
|
||||
---|---|---|---|---|
Home away from home
|
Here is the short block with the modified Ford dump truck pistons I used. This gives 364". Using them require custom machine work on both the pistons and the connecting rods. The top ring groove has a cast iron insert for heavy duty full throttle longevity. Downside is they are heavier than the hubs of hell. Notice the dish which closely matches the Packard combustion chamber. The block was decked square and the pistons are installed only .005" below the block deck surface.
jack vines
Posted on: 2010/11/30 16:22
|
|||
|
Re: Packard V8 in a Studebaker C-cab truck
|
||||
---|---|---|---|---|
Not too shy to talk
|
Yeah...I havent completely decided on what I am going to run on the rear for a bolt pattern. I have the Turner Brake conversion on the front with the Impala hubs. I most likely will run the same on the rear. The rearend I purchased was built new with center section and tubes so I have the option finishing it off the way I like.
Steve
Posted on: 2010/11/30 16:41
|
|||
|
Re: Packard V8 in a Studebaker C-cab truck
|
||||
---|---|---|---|---|
Not too shy to talk
|
Very nice picture Jack! I will be sure my father photo documents the process of the rebuild for everyone to see if they like. The block and all is being steam cleaned now and then the machining will start as well as a balance job.
Steve
Posted on: 2010/11/30 16:42
|
|||
|