Packard Forum Index » Project Blogs

Topic: RIk's 56 ultramatic

Bottom

Previous Topic

Next Topic Register To Post

« 1 ... 55 56 57 (58) 59 60 61 ... 79 »

R H

Re: RIk

#571

Home away from home

12

207907. Theft proof. Number

Attach file:

20220620_173233_(1).jpg (344.19 KB)

20220626_170621.jpg (256.94 KB)

Posted on: 2022/6/20 19:36

Riki

Owen_Dyneto

Re: RIk

#572

Forum Ambassador

Those 1936 plates are unique, to my knowledge the only ones where the series number (14th) was included, preceding the vehicle number.

Posted on: 2022/6/20 20:02

R H

Re: RIk's 56 ultramatic

#573

Home away from home

Thanks

Dave.

Trying to figure out how it got to Texas.

Posted on: 2022/6/20 20:49

Riki

R H

Re: RIk

#574

Home away from home

56

Going to have to replate the door handles.

The blotch won't come out.

Windwings cleaned up.

Attach file:

20220626_170816.jpg (174.40 KB)

20220626_170644.jpg (223.84 KB)

Posted on: 2022/6/26 22:36

Riki

Pgh Ultramatic

Re: RIk

#575

Home away from home

Kanter has NOS door handles. Might be cheaper than replating..replacing... just a thought.

Posted on: 2022/6/27 5:38

R H

Re: RIk's 56 ultramatic

#576

Home away from home

Mister potato .
From kanters voice mail. Not that great.

I'm better off re chroming

Posted on: 2022/7/1 17:58

Riki

R H

Re: RIk

#577

Home away from home

Carpet dads 56 patrician.

After 65 years it still looks new

Attach file:

20220630_154636.jpg (433.67 KB)

20220630_154714.jpg (312.30 KB)

Posted on: 2022/7/1 18:00

Riki

R H

Re: RIk

#578

Home away from home

Got front Windwings in.

Muscled the left .. Then rubber mallet.

Right side had to use heat gun.

Then rubber mallet.

Used silicone grease...

Attach file:

20220703_202802.jpg (211.75 KB)

20220703_202823.jpg (195.98 KB)

Posted on: 2022/7/3 23:43

Riki

R H

Re: RIk

#579

Home away from home

Got the windshield in.

Gerry helped. His son objective observer.

As gerry put it. If the windshield broke. . .

Have some adjusting to do. But was able to lock corners.

Using the sealant steel recommends . is a mess.

It went in smooth. Otherwise..

Found out afterward gerry has the shims...

Attach file:

20220709_173453.jpg (313.41 KB)

20220709_173415.jpg (258.68 KB)

20220709_174133.jpg (205.87 KB)

20220709_174147.jpg (198.46 KB)

Posted on: 2022/7/10 0:25

Riki

R H

Re: RIk

#580

Home away from home

Antenna.

Once you know how.... Not bad.

To get the most off the top piece unscrews.

The motor section. Pretty easy.

The tension on cable is by a spring.

The insulator I'm making from delrin.

Dirty. Commutator. Clean commutator.

Motor. Back together..

Going to have mast re chromed..

3d guys could makes them

The cable they could makes that too.

Attach file: