Packard Forum Index » Project Blogs

Boys will be boys!

ROFPML!!!!!!!!!!!!!!!!!!!!!! A fabulous story Guscha, I can tell that your teachers must have loved having you in their classes!

I've heard stories of hammering a potato into exhaust pipes causing the engine to die of strangulation or picking up when the pressurised potato projectile releases. Or using a hose to fill the exhaust pipe up with water. But Gerd, your schoolboy ingenuity, and thinking on your feet. Can't beat that!

Thursday 22nd July 2010

Not a great deal happening of late. On Tuesday Wade had taken the pumpkin to a diff company at Seven Hills for lapping-in and set-up. They said, with any luck, it could be ready Friday, tomorrow. Wade had also cleaned out the diff housing of old oil and any diff particles yesterday in readiness for the pumpkin's return. And yesterday I took the '41 down to Carburettor Service Company where Tim checked the auto choke butterfly which was found to be dead upright. And so it should be after a 1/2 hour drive in peak time traffic. Tim also took the opportunity to adjust the idle mixture slightly. This morning MBM enterprises swung into action to make some gaskets for the axle housings and bearing retainers on Noel's '39. Also cleaned up the axle housing, seal and bearing retainers and backing plate mounting surfaces. All is now ready for the re-assembly except for the MBM pumpkin gasket which will be made just prior to it's installation.

While I was making gaskets Wade was under the '39's left running board replacing the philips head bolts on the radio aerial with hex head ones, at least that's what he told me, the pic tells a whole different tale. Yesterday Wade had a call from Snapey about the '34 chassis and the remnants of a engine sitting in the workshop. Then today, after confirming with Barry Smith that Matt could use the engine, Wade couldn't find Matt's mobile number. So Matt, if/when you read this could you give Wade a call please? Speaking of giving Wade a call, starliner could you do the same please. Left a message for you on Monday Chris, that your radio is ready for pick up, but I don't think Wade's heard from you yet. And that's the extent of Wade's "paging service" for today! Left Wade hunting for engine parts to go with Barry's engine while I'm now off to see the granddaughters!

Attach file:

---

  (23.07 KB)


  (32.23 KB)


  (34.86 KB)


  (22.74 KB)


  (22.37 KB)


  (41.39 KB)

Thank you for delivering that message Mal, although Wade did leave a voice mail message on my work number but I was a little too snowed under to respond as promptly as I would have liked.

"I love deadlines - it's the wooshing noise they make as they fly past."

I will endeavor to give him a call tomorrow morning. Thanks again.

Friday 23rd July 2010

Drove the '41 down to the workshop and when I arrived what did I find Wade with? Why the fuel tank out of Big Red. Yesterday afternoon Wade had noticed there was a weep from the drain plug on the tank. Decided to fix it but instead of the plug tightening, the whole plug boss turned and a bigger leak immediately resulted! Out with the tank, a lot easier than on the Juniors we've pulled previously because the Senior tank has a straight filler neck not a curved metal filler neck. Once out Wade discovered it had been repaired before and not very well at that. So first up this morning we took the tank around to Emil, the local radiator repair guy, for repair work.

Then, as soon as we returned to the workshop, Wade received a call from Stan to say the new collar and the sleeved shaft for Big Red's water pump were ready. And because Stan is going fishing for a week we immediately went and picked it up. Back at the workshop the pump was reassembled with the interference fit collar pushed into the pump housing, the newly sleeved shaft and new bearings refitted, the ceramic seal fitted, the impeller fitted and then the pulley re-installed. The pulley itself is a big chunk of metal and it had been balanced with holes drilled around it's edge, and for it's size and weight it would need it!

Received a call from Emil to say the fuel tank was done and ready, so off we went again. Turns out the tank had been previously damaged and all around the plug boss it had been patched with body filler! Emil found this out when he went to repair the tank so had to remove all the filler first. Back at the workshop before re-installing the tank Wade commenced repairs on the fuel tanks sending unit. Although Wade had replaced all the wiring and ensured good connections it still read full on the gauge most of the time. Wade disassembled the sending unit, doing this by drilling out the three rivets holding it together to find a lot of corrosion inside. Now cleaned up but more to come, but it's certainly a whole lot cleaner than it was before. Wade's taking it home tonight and will use electrical contact cleaner as a further step in it's rejuvenation.

While Wade was doing that, I thought I'd get MBM into gear on the pumpkin to diff housing gasket for Noel's '39. How to do this though? The diff housing is still under the '39 so access there was cramped. However the pumpkin sent up by Peter Packard is still in the workshop so I eyeballed that. My eyeball observations were that it would need a gasket comprised of 2 concentric circles with a cut out for the oil drain hole and holes of course for the diff housing studs. Was able to turn the crown wheel so that a steel tape could be passed through the hemisphere allowing accurate measurements of both circles diameters. However didn't have a compass and Wade said he'd chased one before without luck although if he'd wanted he could have bought a full set of instruments in order to obtain the one he wanted, but passed on that. What to do? Why find something circular of the right, or close to the right diameter, to draw the circles required. Looked around and a couple of 20 litre drums, one plastic the other metal, looked like they'd be close. The plastic drum was too small but the metal drums base was spot on! So used that as a template and drew around it for the outside of the gasket. The inner circle was more of a challenge, but wandering around espied the hubcaps on Big Red. Fortunately with the front wheels off Big Red there was a hubcap readily available, and although the outside diameter was too great, the diameter where it tapered down to fit the wheel was almost perfect. Then followed some positioning jiggling of the hubcap inside the outer drawn circle and then by leaning the pen at an angle a line was drawn for the inner circle. Cut out the outer circle allowing a fraction more "just in case" and similarly with the inside circle allowing even more "just in case". Cleaned up the gasket surface of the pumpkin, which was mounted on some special Packard pumpkin stands, and a trial fit. Turns out the inner circle "just in case" wasn't needed and after a bit of pruning it fitted! Then using a small ball peen hammer knocked out the holes for the studs and the indentation for the oil drain plug. Then as I'm feeling quite pleased with myself, reality in the form of Wade intervened. Asked me about the crescent shaped cut outs for crown wheel clearance at top and bottom. They don't appear on the pumpkin but they are on the diff housing. So under the '39 with gasket and hammer and after some remedial work NOW had a MBM gasket for Noel's '39 diff. Wade rang about the pumpkin this morning but it won't be ready till late this afternoon so will be picked up Monday morning.

Quote: Matt for calling this morning, but referencing me to Wade as his secretary? I just try to help if I can! Pic's below of the engine and the bits and pieces that Wade rounded up yesterday.

Attach file:

---

  (24.72 KB)


  (30.65 KB)


  (30.51 KB)


  (37.51 KB)


  (18.59 KB)


  (16.88 KB)


  (20.49 KB)


  (17.92 KB)


  (28.30 KB)


  (22.48 KB)


  (36.71 KB)


  (20.90 KB)


  (23.47 KB)


  (21.61 KB)


  (27.58 KB)


  (28.43 KB)


  (38.31 KB)


  (24.14 KB)


  (38.81 KB)


  (35.49 KB)


  (26.18 KB)


  (37.02 KB)


  (32.48 KB)


  (37.36 KB)

The industrious and generous attitudes of the gentlemen of 'Wades Workshop' never cease to amaze me! Thank you Wade (and Barry) for putting all of that together for me - I am very much obliged to you, although I hope your repayment, as discussed today, will go some little way in expressing my gratitude. And I really do mean that.

Also I am sorry, Mal, if my reference to your secretarial skills was in any way offensive, but I think it is important that, as a well rounded individual (insert smirk here), we are able to function in a number of roles. I think you should take it as a complement that I think you would make a fine secretary. Indeed if I may be so bold as to offer some advice for the future, I think that given your complexion you need to be careful in the selection of the shade of lipstick to be used, and maybe a little less blush would work better. Also you may want to consider leaving the fishnet stockings and suspenders in the drawer at home...

And I really DON'T mean any of that!

Thank you Mal for all your efforts here and your help to me personally. I always look forward to the opportunity of stealing a few minutes from work each day in order to check in on 'Wades Workshop' and I hope to catch up with you all again soon.

Hi Mal, can you elaborate on "On Tuesday Wade had taken the pumpkin to a diff company at Seven Hills for lapping-in and set-up." From a previous post. I am interested in what is meant by "lapping in". I have set up ring and pinions by means of getting the correct contact patch and backlash, but am unfamiliar with lapping the gears in. I am curious because I have a 3.92 set that I need to replace bearings on eventually and would like to ensure they run quiet and smooth.

Thanks!

Quote:Jim,

Quick google search found this series of videos.

Lapping in1

Lapping in2

Lapping in3
Quote:Matt,

You'll no doubt remember politician Alexander Downer and the fishnet stockings and high heels he donned for charity back in 1996, the images of which stayed with him throughout his political career.

Mal, thanks very much for posting the links. I have never heard of, or seen this process until your mention here. I will have to investigate and see if there is such equipment locally. I bet it makes for a very quiet fitment.

Jim