Re: position of R9 Lockout Control Lever on OD case ?
|
||||
---|---|---|---|---|
Home away from home
![]() ![]() ![]() |
I found three switches in the engine compartment -drivers side 1. The accelerator switch midway on the firewall(still hooked up ). 2. The reverse safety switch mounted on the shift rod ( not hooked up). 3. A third mounted at bottom of firewall by accelerator - guess this is the kickdown switch .
Posted on: 2012/10/27 17:01
|
|||
|
Re: position of R9 Lockout Control Lever on OD case ?
|
||||
---|---|---|---|---|
Forum Ambassador
![]() ![]() ![]() |
Sounds as if this switch mounted low on the engine might be missing.
Is the rest of the Electromatic present? You might download the training manual for "Clutch and Electromatic Clutch". That gives a good description of the postwar system and shows all components. Note: the book labeled "Electromatic Clutch" is for the prewar version & is a considerably different system than yours. Nice if yours is still there. Many Electromatics were disabled or even partially or completely removed. Nice conversation starter and feature when they work but they could be temperamental. If out of adjustment, even somewhat irritating. Many times they were not under stood or service people didn't want to take the time to adjust or keep them adjusted properly so away they went.
Posted on: 2012/10/27 17:50
|
|||
Howard
|
||||
|
Re: position of R9 Lockout Control Lever on OD case ?
|
||||
---|---|---|---|---|
Home away from home
![]() ![]() ![]() |
Well - Guess what - I just went and looked . The direst speed switch is still there. Hard to see and I didnt know what I was looking at. Looks like all of the Electromatic Clutch parts are there - just not hooked up - I see the cable from the power cylinder is broken or disconnected . It should be connected to the starter- right. Dont know if I will ever get the clutch to work - but a least it's there. I assume the overdrive will work even if the clutch is disabled - right ? I know I have lots to do.
Posted on: 2012/10/27 18:50
|
|||
|
Re: position of R9 Lockout Control Lever on OD case ?
|
||||
---|---|---|---|---|
Forum Ambassador
![]() ![]() ![]() |
I assume the overdrive will work even if the clutch is disabled - right ? I know I have lots to do.
Sure, there are quite a few who have not returned the Electromatic to operating condition but continue to have functional overdrive. Yes, the Electromatic cable connects to the starter and the chances are quite good that the diaphragm in the vacuum cylinder would need to be replaced to get the Electromatic to function - not that that is much of a job in itself though the rest of the system may have issues as well. I've only ever driven a handful of Packards in which the Electromatic functioned just beautifully and I was really impressed by it, but in the end I just decided to do w/o it.
Posted on: 2012/10/27 18:56
|
|||
|
Re: position of R9 Lockout Control Lever on OD case ?
|
||||
---|---|---|---|---|
Forum Ambassador
![]() ![]() ![]() |
The cable end is attached to a bracket clamped to the starter motor and then goes thru the pulley on clutch arm then to the rubber diaphragm in power unit. The cable and diaphragm are readily available. The switch on dash will turn off the clutch and once off, you drive the car as per any other stick shift.
Posted on: 2012/10/27 18:59
|
|||
Howard
|
||||
|
Re: position of R9 Lockout Control Lever on OD case ?
|
||||
---|---|---|---|---|
Home away from home
![]() ![]() ![]() |
Hi HH56 - How many screws hold the R9 relay to the firewall-my relay is missing and I see only one screw on the right side and another larger hole - Is this for a clip to hole the cable and the relay ? Thanks
Posted on: 2012/11/3 9:51
|
|||
|
Re: position of R9 Lockout Control Lever on OD case ?
|
||||
---|---|---|---|---|
Forum Ambassador
![]() ![]() ![]() |
There are 2 mounting screws. The photo on page 2 in post 17 of this thread and this 22nd series firewall photo from another thread shows the general loom layout. Also including photos of the relay with and without cover. If you have a hole not shown on one of the firewall photos then must have been added by a previous owner.
Posted on: 2012/11/3 10:04
|
|||
Howard
|
||||
|
Re: position of R9 Lockout Control Lever on OD case ?
|
||||
---|---|---|---|---|
Home away from home
![]() ![]() ![]() |
Thanks for your help - We can forget about the relay while I ask about another problem . As I was trying to get a tail light / stop light to work, I must have blown something. I now have no head lights or tail lights - the signal lights still work . Is there a fuse or circuit breaker for head lights -tail lights ?
Posted on: 2012/11/3 19:19
|
|||
|
Re: position of R9 Lockout Control Lever on OD case ?
|
||||
---|---|---|---|---|
Forum Ambassador
![]() ![]() ![]() |
In the 48's power is fed from starter solenoid battery post to ammeter. Out of ammeter to a splice which feeds ignition switch, an aux circuit breaker input post located on back of cluster and then using the CB post as a either a tie or another splice point, on to the headlight switch.
The aux CB feeds the courtesy lights and the brake lights. The headlight switch should have a breaker on the end which protects the headlights, parking, instrument and tail lights. It should be self resetting unless it has failed or someone has changed it to something else. The turn signals have a separate inline fuse off the ign switch. Here is a piece of photo I borrowed from one BDeB posted showing the headlight switch and breaker. Attach file: ![]() ![]()
Posted on: 2012/11/3 19:50
|
|||
Howard
|
||||
|