Re: 1956 Caribbean hardtop options on a Four Hundred
|
||||
---|---|---|---|---|
Forum Ambassador
![]() ![]() ![]() |
I bought an extrusion several years ago from Joel. It looks close but the rubber is not as stiff as an original. My first 56 had an original. It was very stiff.
Posted on: 2016/3/25 17:33
|
|||
|
Re: 1956 Caribbean hardtop options on a Four Hundred
|
||||
---|---|---|---|---|
Home away from home
![]() ![]() ![]() |
Thanks Owen_Dyneto! That is a great lead, and thanks Randy, I will try to get one!
I will report on the engine block code next week.
Posted on: 2016/3/25 17:34
|
|||
|
Re: 1956 Caribbean hardtop options on a Four Hundred
|
||||
---|---|---|---|---|
Home away from home
![]() ![]() ![]() |
Hello Victor,
I do not know if all CKD/KD Packards were sent via ECA. I only know that some obviously were. The fellow who told me certainly should have known with his position at ECA, Inc. With trainloads of vehicles going to ECA as Packard West Coast Distributor and with main routes into Mexico from SoCal and Mexico being the next entity south of California, there is logic here. Ford was doing likewise, at least as recently as the 1980s and probably well after...ask me how I know. And remember, Mr. Anthony spelled it Earle... with an "e" on the end. RE: the Creative Industries book, you can find preview info about it on Amazon.com. Anyway, the Scottish Heather looks gorgeous in the photos. Enjoy that beautiful Four Hundred!
Posted on: 2016/3/25 17:37
|
|||
|
Re: 1956 Caribbean hardtop options on a Four Hundred
|
||||
---|---|---|---|---|
Home away from home
![]() ![]() ![]() |
Gracias, Leeedy!
Shortest way for sure would be directly from Detroit to Puebla (where O'Farril was assembling Packards and which is even a bit farther south than Mexico city) via Texas, but of course, I don't have a clue as to why send them to California first... perhaps Earle (with an E, thanks!) was the distributor who had the relationship with the O'Farril family... or as you say, some were sent by him directly. Thanks again! victor
Posted on: 2016/3/25 17:45
|
|||
|
Re: 1956 Caribbean hardtop options on a Four Hundred
|
||||
---|---|---|---|---|
Home away from home
![]() ![]() ![]() |
Quote:
Well? Again, I don't know about this specific car for sure... or anything about Packard's corporate policies vis-a-vis Mexico. However, one could look at it this way: Prepare a set of auto shipping train cars from Detroit... especially just to go all the way directly to Mexico? Or add a few more cars KD'd onto a trainload already bound for SoCal, and then route the handful out from there? Shortest distance isn't always the cheapest-especially when it comes to economies of scale. And remember too that Mr. Anthony wasn't just West Coast Distributor... he was also on the Packard Board of Directors too... at least for a while.
Posted on: 2016/3/25 17:58
|
|||
|
Re: 1956 Caribbean hardtop options on a Four Hundred
|
||||
---|---|---|---|---|
Home away from home
![]() ![]() ![]() |
Got it. Thanks!
I just tried to contact Joel Ray via his page on ebay, as I couldn't find the rubber shield or insulator there. Hope he still handles it.
Posted on: 2016/3/25 18:55
|
|||
|
Re: 1956 Caribbean hardtop options on a Four Hundred
|
||||
---|---|---|---|---|
Home away from home
![]() ![]() ![]() |
Joel does not handle the part any more, but he was kind enough to offer taking pics of the one on his car and sending them. At least that way I will see if I can find something to duplicate it.
Posted on: 2016/3/26 11:49
|
|||
|
Re: 1956 Caribbean hardtop options on a Four Hundred
|
||||
---|---|---|---|---|
Forum Ambassador
![]() ![]() ![]() |
Should Joel forget, let me know and I can take pictures of the original one on my car. It's a simple box section of extruded rubber with a full-length slit cut across the narrow dimension, Length 3-3/16, width 25/32, height 31/32, wall thickness 1/8". The slit is more than just a cut, a small amount of material is actually removed.
Posted on: 2016/3/26 13:05
|
|||
|
Re: 1956 Caribbean hardtop options on a Four Hundred
|
||||
---|---|---|---|---|
Home away from home
![]() ![]() ![]() |
O_D, from your description it reads like one could be easily made from either square section or round rubber product. Can the VR be turned around so the terminals are on the bottom without drilling any additional holes in the radiator bracket?
(o{}o)
Posted on: 2016/3/26 14:54
|
|||
We move toward
And make happen What occupies our mind... (W. Scherer) |
||||
|